Stihl 4137 · Section W · 21 of 24 · 17 parts
Oil tank, Chain sprocket cover
Fits HT 70, HT 75.
Historical fitment & changes (12) — includes parts and conditions not shown on this drawing.
Parts (17)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4138 351 0300 | Oil tank | 1 |
| 2 | 4138 351 1000 | Gasket | 1 |
| 3 | 0000 951 1100 | Screw IS-D5x20 | 4 |
| 4 | 0000 350 0526 | Filler cap | 1 |
| 5 | 9645 948 2470 | O-ring 23x3 | 1 |
| 6 | 1123 648 6600 | Bumper strip | 2 |
| 7 | 1129 007 1000 | Spur gear / chain adjusting screw kit | 1 |
| 8 | 1123 640 1900 | Tensioner slide | 1 |
| 9 | 1123 664 1400 | Thrust pad | 1 |
| 10 | 1123 664 2200 | Cover | 1 |
| 11 | 4138 640 1703 | Chain sprocket cover | 1 |
| 12 | 4138 640 1701 | Chain sprocket cover | 1 |
| 13 | 0000 961 1409 | Ring | 1 |
| 14 | 0000 955 0801 | Hexagon nut M8 | 1 |
| 15 | 3610 000 0044 | 61PMM3 chain Picco Micro Mini 3 | 1 |
| 16 | 3005 000 3905 | Guide bar 30cm/12" 1,1mm/0.043" 3/8"P | 1 |
| 17 | 4138 967 3701 NLA | Instruction label | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · HT 75
HT 75: oil tank removal and oil pump slot orientation
Retain the strainer, M5 extraction screw and engine-facing pump slot; do not invent a pump torque.
- Remove the oil filler cap with its retainer and remove the tank screws. Swing the tank counterclockwise and lift it away; installation reverses removal.
- With the tank removed, ease rubber seal (1) out of the gearbox housing and remove filter screen (2). Screw an M5 screw at least 25 mm long (printed 1 inch) into the pump and pull it out using the screw. Clean the oil passages.
- Align the oil pump to the symbol beside the bore: its slot must point toward the engine. Screw an M5 screw into the pump to press it home, then remove the temporary screw. Reverse the remaining removal steps for assembly.
- The source gives no oil-pump, screen, seal or screw order number, press depth or tightening torque. The M5 screw is a temporary extraction/pressing aid, not a retained replacement component.
- TI14/1999 supersedes and replaces TI03/1997. It specifies properly trained and authorized service personnel and use of the illustrated parts list for orientation. These are historical source instructions, not a project hardware test or authorization to operate a machine.
- Scope is HT 75, printed series 4138. The retained exact-model IPL is grouped under 4137 and also names HT 70; this navigation link does not establish series equivalence or extend these instructions to HT 70 or later configurations. No production serial is supplied by this bulletin.
Source: TI 14/1999, p. 5 · TI 14/1999, p. 6 — 2.2–2.3: tank removal, seal/screen, temporary M5 screw and pump orientation.
No additional parts-table entry added.
Service note · HT 75
HT 75: chain tensioner manual dependency
TI14/1999 refers chain-tensioner service to the E14/E20 or E140/E160/E180C workshop manual.
Model-specific manual evidence: HT 75: later manual guidance for side chain tensioner
- Section 2.4 contains a reference only: see the workshop manual for E 14, E 20 or E 140, 160, 180 C. It does not describe a tensioner procedure, part interchange, torque or a changeover.
- The named E 140 / E 160 / E 180 C workshop-manual family is available in the retained service documentation as edition 2003-01. Linked later guidance now preserves its side-tensioner procedure and lubricant reference. The exact contemporaneous edition intended in 1999 remains unestablished; the earlier bounded docs/service-manuals filename search did not cover this catalog resource. Do not report the entire manual family as absent or silently backdate the later instructions.
- The reference is preserved as an HT 75 service dependency, not an assertion that all parts of those electric saws fit the pole pruner.
- TI14/1999 supersedes and replaces TI03/1997. It specifies properly trained and authorized service personnel and use of the illustrated parts list for orientation. These are historical source instructions, not a project hardware test or authorization to operate a machine.
- Scope is HT 75, printed series 4138. The retained exact-model IPL is grouped under 4137 and also names HT 70; this navigation link does not establish series equivalence or extend these instructions to HT 70 or later configurations. No production serial is supplied by this bulletin.
Source: TI 14/1999, p. 6 — 2.4: chain tensioner reference only; external procedure not supplied.
No additional parts-table entry added.
Service note · HT 75
HT 75: superseded 1997 oil tank and pump service
Superseded by TI14/1999. Preserve counterclockwise tank removal and the pump groove facing the tube mount.
Later reviewed guidance: HT 75: oil tank removal and oil pump slot orientation
- Superseded historical instruction: TI14/1999 explicitly supersedes and replaces TI03/1997. Follow the linked later source for its revised procedure; the two versions must not be blended into an invented sequence.
- TI03/1997 restricts inspection, service and repair to trained, authorized personnel and refers to the illustrated spare-parts list for orientation. This is an offline source record, not a hardware experiment.
- The source names only HT 75, type 4138. The exact-model IPL is filed under 4137 and also names HT 70; that navigation link does not establish series equivalence, extend this procedure to HT 70 or prove applicability to every later HT 75. No production serial is printed.
- Remove filler cap with retainer, remove oil-tank screws and swivel tank counterclockwise to remove it. Assemble tank parts in reverse order.
- With tank removed, pull rubber buffer (1) from the gearbox housing and remove strainer (2). Thread an M5 screw at least 25 mm long into the oil pump and pull it out by the screw. No screw, pump, strainer or buffer order number is supplied.
- Insert oil pump according to the symbol beside the opening: the full-length groove must face the tube mount. Thread the M5 screw into the pump and press the pump home; remove the screw and assemble remaining parts in reverse order. The screw is a temporary tool, not a retained pump component; no pressing depth, force or torque is printed.
Source: TI 3/1997, p. 5 · TI 3/1997, p. 6 — Complete2.2–2.3: tank, buffer/strainer, M5 extraction/pressing aid and groove orientation.
No additional parts-table entry added.
Service note · HT 75
HT 75: superseded 1997 chain-tensioner reference
Superseded by TI14/1999. The E14/E20 repair-manual dependency is not a tensioner procedure or interchange assertion.
Later reviewed guidance: HT 75: chain tensioner manual dependency
- Superseded historical instruction: TI14/1999 explicitly supersedes and replaces TI03/1997. Follow the linked later source for its revised procedure; the two versions must not be blended into an invented sequence.
- TI03/1997 restricts inspection, service and repair to trained, authorized personnel and refers to the illustrated spare-parts list for orientation. This is an offline source record, not a hardware experiment.
- The source names only HT 75, type 4138. The exact-model IPL is filed under 4137 and also names HT 70; that navigation link does not establish series equivalence, extend this procedure to HT 70 or prove applicability to every later HT 75. No production serial is printed.
- Section 2.4 says only: see Repair Manual E 14, E 20. It supplies no tensioner procedure, torque, part number or physical interchange assertion.
- The exact E14/E20 manual was not established in the admitted reader set or the bounded mounted service-manual filename inventory. The adjacent HT75 PDF was checked for the referenced material; it is not silently treated as the missing electric-saw manual. This named dependency remains a source gap, not proof that no copy exists anywhere.
Source: TI 3/1997, p. 6 — Complete2.4: E14/E20 chain-tensioner repair-manual dependency.
No additional parts-table entry added.
Service note · HT 75
HT 75 introduction: 14-inch PMN and seven-tooth sprocket
Printed 14 in bar, 3/8-inch Picco-Micro-Narrow PMN chain with 44 links, and 7-tooth 3/8 P spur sprocket.
- Page 1 calls the equipment Picco-Mini bar and chain as for the 017. Section 3 specifies bar length 14 in; Oilomatic 3/8-inch Picco-Micro-Narrow (PMN), 44 links; Rollomatic Mini guide bar; and spur chain sprocket, 7 teeth, for 3/8 P.
- Keep the printed 14 IN / 44 LINKS combination without correcting it from the later IPL. The later exact-model oil-tank/cover sheet lists a 12-inch bar and 61PMM3 chain; the gearhead sheet lists both six- and seven-tooth sprockets. Neither later listing proves the original TI combination is correct or establishes an approved substitution.
- The bulletin provides no bar, chain or sprocket ordering numbers, no drive-link gauge and no chain-length measurement. Do not invent them from the 017 comparison or use the source alone as an assembled-fit verification.
- The original heading specifies HT 75, type 4138. Later exact-model IPL navigation is grouped under 4137 and also names HT 70; this does not establish series equivalence or HT 70 applicability. No introduction serial is printed. No hardware operation was performed.
Source: TI 47/1996, p. 1 · TI 47/1996, p. 2 · TI 47/1996, p. 3 — HT 75 introduction: 14-inch PMN and seven-tooth sprocket.
No additional parts-table entry added.
Service note · HT 75
HT 75 introduction: six fastening rows and M8 adhesive condition
2.5 / 3.0 / 4.5 Nm location-specific screws; M8 bar fixture uses medium-grade adhesive and 19.5 Nm.
- Section 6.1 row 1: socket-head screw IS-DG5x12, oil tank / gear housing, 2.5 Nm (1.8 ft. lbs.). The later oil-tank IPL lists IS-D5x20 instead; do not substitute that screw or its number into this historical row.
- Rows 2 and 3: socket-head screw IS-M5x20, clamp / LARGE protective tube and clamp / SMALL protective tube, each 3.0 Nm (2.2 ft. lbs.). Preserve both locations; this is not a general M5 torque.
- Row 4: socket-head screw IS-M6x14, clamping collar / carrying ring, 4.5 Nm (3.3 ft. lbs.). Row 5: socket-head screw IS-M6x20, clamp / power unit / shaft, 4.5 Nm (3.3 ft. lbs.).
- Row 6: SET SCREW M8, bar fixture, has blank torque cells and remark 1. Remark 1 supplies medium-grade adhesive, for example Loctite 243, and 19.5 Nm (14.4 ft. lbs.). The blank is not zero torque. No set-screw length or order number is supplied.
- These are the six rows printed in the 1996 introduction. Later TI03/1997 and TI14/1999 distinguish AV-sleeve fixing/clamping screws and gearbox clamps with other values; do not reconcile differently named locations solely by thread size or transfer 19.5 Nm to the bar nut.
- The original heading specifies HT 75, type 4138. Later exact-model IPL navigation is grouped under 4137 and also names HT 70; this does not establish series equivalence or HT 70 applicability. No introduction serial is printed. No hardware operation was performed.
Source: TI 47/1996, p. 3 — HT 75 introduction: six fastening rows and M8 adhesive condition.
No additional parts-table entry added.
Service note · HT 70
HT 70: 1998 cutting attachment
12-inch Rollomatic Mini, 3/8-inch Picco-Micro-Mini (PMN), 44 drive links and a seven-tooth 3/8 P spur sprocket form the printed combination.
- The printed cutting attachment is: 12-inch cutting length; 3/8-inch Oilomatic chain, PICCO-MICRO-MINI (PMN), 44 DRIVE LINKS; Rollomatic Mini guide bar; 7-TOOTH 3/8 P SPUR SPROCKET.
- The source does not give a chain gauge, bar mount identifier, bar/chain/sprocket order number or alternative-length compatibility. No such value is inferred from PMN branding, the later IPL, or an assumed modern replacement.
- This is the introductory combination, not a claim that every 12-inch or every 3/8-inch chain fits. The retained shared catalog sheets are navigation references only.
- Historical HT 70 only. TI35/1998 calls this series 4138; the retained exact-model IPL is filed under 4137. That navigation association does not establish series equivalence, extend these assertions to HT 75 or later variants, or prove physical interchange. No production serial or current stock claim is supplied. No hardware operation was performed.
Source: TI 35/1998, p. 2 — Section 3 complete.
No additional parts-table entry added.
Service note · HT 70
HT 70: delegated oil tank and pump service
Counterclockwise tank removal; temporary M5 screw at least 25 mm long; pump groove faces the tube mount in TI03/1997.
- Remove filler cap with its retainer, remove oil-tank screws, and swivel tank COUNTERCLOCKWISE to remove it. Reassemble tank parts in reverse order.
- With tank removed, pull rubber buffer (1) from gearbox housing and remove strainer (2). Thread an M5 screw AT LEAST 25 mm LONG into the oil pump and pull it out by the screw. No buffer, strainer, pump or screw order number is printed.
- Insert pump according to the symbol beside the opening: the FULL-LENGTH GROOVE MUST FACE THE TUBE MOUNT. Thread the M5 screw into the pump and press the pump into position; REMOVE THE SCREW and reassemble remaining parts in reverse order. The screw is a temporary extraction/pressing aid, not a retained pump component. No pressing depth, force or torque is specified.
- TI14/1999 uses rubber seal/filter screen wording, adds cleaning the oil passages and describes the slot facing the ENGINE. Those are separately dated HT75 comparison statements, not a silently merged HT70 sequence; actual housing symbol/configuration remains essential.
- TI03/1997 is a historical, superseded source: TI14/1999 explicitly replaces it but names HT75. The later lubricant changes and friction-clutch qualification are retained in the separate edition-boundary note, not silently prescribed for every HT70. TI03/1997 requires trained, authorized personnel and use of the illustrated parts list for orientation.
- Historical HT 70 only through the explicit TI35/1998 section 6.1 GEARHEAD reference to TI03/1997. This is not inheritance of the HT75 telescopic shaft, paired-shaft replacement, or its labor allowance. Printed series 4138 and catalog 4137 remain separate identities; shared-sheet navigation is not proof of interchange or applicability to later configurations. No hardware operation was performed.
Source: TI 35/1998, p. 4 — Section 6.1 explicit HT70 gearhead delegation; Complete 2.2–2.3 tank removal, extraction aid, pump orientation and assembly.
Referenced bulletin evidence: TI 3/1997, p. 5 · TI 3/1997, p. 6 — Complete 2.2–2.3 tank removal, extraction aid, pump orientation and assembly.
Referenced bulletin evidence: TI 14/1999, p. 1 · TI 14/1999, p. 4 · TI 14/1999, p. 5 · TI 14/1999, p. 6 — Supersession, HT75 model boundary, sections 2.1–2.4 and 3 lubricant changes; comparison only.
No additional parts-table entry added.
Service note · HT 70
HT 70: gearhead corrections and tensioner dependency
TI14/1999 supersedes the delegated source but names HT75; lubricant changes, friction-clutch TI36/1998 and E14/E20 tensioner manual remain separately scoped.
- TI35/1998 section 6.1 expressly delegates HT70 GEARHEAD procedures to TI03/1997. That is positive historical applicability evidence for the referenced gearhead sections, not permission to extend all HT75 shaft procedures or assume all future HT75 revisions apply to HT70.
- TI14/1999 page 1 explicitly supersedes and replaces TI03/1997 and names HT75, series 4138. Its section 2.1 adds TI36/1998 for versions with a FRICTION CLUTCH. The retained TI36/1998 has now been reviewed: it expressly covers HT75 and its telescopic-drive-shaft overload case; it does not establish HT70 retrofit applicability. See the separate friction-clutch scope note.
- TI14/1999 says further testing changed lubricant use: section 3.1 assigns brushcutter gear lubricant 0781 120 1117 / 0781 120 1118 to the GEARBOX; section 3.2 specifies STIHL synthetic two-stroke engine oil for DRIVE SHAFTS; section 3.3 assigns grease 0781 120 6602 to the DRIVE SHAFT IN PLASTIC LINER. These are HT75 comparison statements, not an HT70 product-substitution list.
- TI35/1998 instead lists 0781 120 6602 for GEARBOX and0781 120 1109 for DRIVE SHAFT, while 0781 120 1111 is for OIL SEALS. Preserve this application conflict. The HT70 rigid-shaft exception and later bulletin model scope prevent silently swapping those applications or treating tube sizes as fill quantities.
- TI03/1997 section 2.4 supplies ONLY a reference to Repair Manual E14, E20 for the chain tensioner. TI14/1999 section 2.4 also names E140, E160, E180C. The available 2003-01 electric-saw manual has been visually reviewed as comparison evidence; it is not the exact E14/E20 source and no HT70 procedure is silently transferred. See the separate tensioner-manual edition note.
- Telescopic-shaft sections 1.1–1.3 and the HT75 shaft labor time are excluded from this gearhead inheritance. The separate TI35/1998 HT70 repair-time note retains its own table. No tensioner procedure or friction-clutch servicing is fabricated.
- TI03/1997 is a historical, superseded source: TI14/1999 explicitly replaces it but names HT75. The later lubricant changes and friction-clutch qualification are retained in the separate edition-boundary note, not silently prescribed for every HT70. TI03/1997 requires trained, authorized personnel and use of the illustrated parts list for orientation.
- Historical HT 70 only through the explicit TI35/1998 section 6.1 GEARHEAD reference to TI03/1997. This is not inheritance of the HT75 telescopic shaft, paired-shaft replacement, or its labor allowance. Printed series 4138 and catalog 4137 remain separate identities; shared-sheet navigation is not proof of interchange or applicability to later configurations. No hardware operation was performed.
Source: TI 35/1998, p. 4 — Section 6.1 explicit HT70 gearhead delegation; Section 2.4 tensioner reference and later correction boundaries.
Referenced bulletin evidence: TI 3/1997, p. 6 — Section 2.4 tensioner reference and later correction boundaries.
Referenced bulletin evidence: TI 14/1999, p. 1 · TI 14/1999, p. 4 · TI 14/1999, p. 5 · TI 14/1999, p. 6 — Supersession, HT75 model boundary, sections 2.1–2.4 and 3 lubricant changes; comparison only.
No additional parts-table entry added.
Service note · HT 70
HT 70: HT75 friction-clutch change is not an HT70 retrofit approval
TI36/1998 serial 2 39 949 387 and kit 4138 007 1001 apply to HT75; HT70 applicability is not established.
- TI36/1998 names only HT75, series 4138. Its section 1 introduces the chain-sprocket friction clutch from serial 2 39 949 387 to reduce load on the MULTI-PART TELESCOPIC drive shaft. TI35/1998 explicitly distinguishes the HT70 RIGID shaft. The shared gearhead drawing and shared catalog sheet do not transfer that serial or establish an HT70 conversion.
- Section 1.4.3 says EVERY HT75 can be converted with complete kit 4138 007 1001; it does not say every HT70. The separate kit instruction sheet identifies replacement parts. No HT70 retrofit or individual part interchange is inferred from that statement or from the section 1.5 parts table.
- The left-hand collar screw, complete three-cup-spring replacement, washers supplied with the sprocket, 6 Nm collar-screw torque and 5–14 Nm slip-test range in TI36/1998 remain HT75 friction-clutch guidance. They are not HT70 setting/testing specifications. The ring supply conflict between section 1.4.2 and the spare-availability table remains retained in the existing HT75 notes.
- TI14/1999 points versions WITH a friction clutch to TI36/1998, but also names HT75. This resolves the dependency review as a MODEL/CONFIGURATION BOUNDARY, not proof that no HT70 ever had a friction clutch. The older TI03/1997 sprocket-removal sequence must not be assumed suitable for an unverified later assembly.
- Historical HT 70 only: TI35/1998 provides the repair-source context, not blanket inheritance of later HT75 revisions. Printed series 4138 and catalog 4137 remain separate identities. No hardware operation was performed.
Source: TI 35/1998, p. 4 — HT75 friction-clutch change is not an HT70 retrofit approval.
Referenced bulletin evidence: TI 36/1998, p. 1 · TI 36/1998, p. 2 · TI 36/1998, p. 3 · TI 36/1998, p. 4 — HT75-only model heading, telescopic-shaft purpose, retrofit scope and service/table context.
No additional parts-table entry added.
Service note · HT 70
HT 70: chain-tensioner manual found, exact historical applicability unresolved
The available 2003-01 E140/E160/E180C manual separates front, side and quick tensioners; it is not the exact E14/E20 source.
- TI35/1998 delegates HT70 gearhead work to TI03/1997; section 2.4 of that source says only see Repair Manual E14, E20. TI14/1999 expands the manual reference to E140, E160, E180C, but its heading remains HT75. That later reference is a useful locator, not by itself an HT70 applicability bridge.
- RA_100_00_01_02.pdf is locally available. Its cover says E140, 160, 180 and 2003-01; the introduction names E140, E160 and E180C. The 2006 layout timestamp on the cover is distinct from the printed edition. It must not be renamed an E14/E20 manual or treated as the original 1997/1998 edition.
- PDF18 (printed17) contains separate front and side chain-tensioner sections 7.1 and 7.2. The front mechanism uses a tensioning nut, adjusting screw and cover; the side mechanism additionally distinguishes thrust pad, spur gear and tensioner slide. Its side-tensioner teeth inspection and lubricating-grease reference belong to that mechanism. PDF19 (printed18), section 7.3, concerns the quick-tensioner wingnut and cover. Adjacent chain-brake section 8.1 is not tensioner service.
- These illustrations are reviewed comparison evidence, NOT three interchangeable HT70 procedures. No electric-motor housing removal, chain-brake procedure, quick-tensioner conversion, grease order number or torque is prescribed for HT70 from these pages. Exact HT70 mechanism/edition evidence is still required before transferring the procedure.
- The reused bounded inventory contains 808 PDF paths; the available electric-saw candidate and HT components manual were checked directly. No exact E14/E20 repair manual was established in that inventory. This is a named historical-source gap, not universal absence, nor a reason to skip the other locally available HT70 manual sections.
- Historical HT 70 only: TI35/1998 provides the repair-source context, not blanket inheritance of later HT75 revisions. Printed series 4138 and catalog 4137 remain separate identities. No hardware operation was performed.
TI dependency: TI 35/1998, p. 4 — chain-tensioner manual found, exact historical applicability unresolved.
Referenced bulletin evidence: TI 3/1997, p. 6 — Section 2.4 exact E14/E20 reference.
Referenced bulletin evidence: TI 14/1999, p. 6 — Section 2.4 later electric-saw reference; HT75 comparison only.
Later manual evidence: STIHL E 140, 160, 180 (introduction: E 180 C) (2003-01), section Edition/model identity and complete sections 7.1–7.3; comparison only, not an admitted HT70 procedure, PDF pages 1, 3, 18, 19
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Service note · HT 75
HT 75: later manual guidance for side chain tensioner
The retained 2003 electric-saw manual supplies the side-tensioner sequence; it is not proof of the exact 1999 procedure.
- TI14/1999 section 2.4 delegates chain-tensioner service to the E 14 / E 20 or E 140 / E 160 / E 180 C workshop manual. The retained E 140, 160, 180 manual is edition 2003-01; its introduction explicitly includes E 180 C. This is later evidence for the named manual family, not the unidentified edition available in 1999. The 1998 copyright and 2006 cover-production stamp are not its edition date.
- The HT 75 oil-tank/chain-sprocket-cover sheet W shows a side-tensioner group: spur gear/adjusting screw kit, tensioner slide, thrust pad and cover. That supports consulting section 7.2, not applying the adjacent front-tensioner or quick-tensioner instructions to every HT 75. The manual does not establish electric-saw/HT 75 part interchange or compatibility with every later pole-pruner configuration.
- Later manual section 7.2, printed page 17 (PDF page 18): remove the chain sprocket cover and take out the complete chain tensioner. Remove thrust pad (1); rotate spur gear (2) to unscrew adjusting screw (3) fully from tensioner slide (4). The drawing numbers are local callouts, not order numbers or HT 75 catalog positions.
- Pull spur gear (1) from cover (2) in drawing 100RA075 VA. In the next drawing, pull off tensioner slide (1) and take out adjusting screw (2). Inspect the teeth on the spur gear and adjusting screw; replace both parts if necessary. Reassemble in reverse order. No tensioner torque, acceptance tooth-wear dimension or screw order number is supplied here.
- Before refitting, coat the adjusting-screw and spur-gear teeth with lubricating grease, referring to section 10.2. Its lubricating-grease row is 0781 120 1111, described for sliding/pivot points and the oil-pump pin. It is not the separately listed multipurpose grease 0781 120 1109 for the ring gear and washers, or the TI shaft-liner grease 0781 120 6602. This cross-reference does not assert that all these greases are interchangeable.
- The section 7.2 sprocket-cover prerequisite points to manual section 4.1. The cited cover-only steps are to unscrew its nut and remove the chain sprocket cover. Only those cover-removal steps are used here; electric-saw electrical disassembly, front/quick tensioners, motor repairs and chain-brake procedures are not imported into HT 75 service. This bounded reference is not a complete pole-pruner repair manual.
- TI14/1999 supersedes and replaces TI03/1997. It specifies properly trained and authorized service personnel and use of the illustrated parts list for orientation. These are historical source instructions, not a project hardware test or authorization to operate a machine.
- Scope is HT 75, printed series 4138. The retained exact-model IPL is grouped under 4137 and also names HT 70; this navigation link does not establish series equivalence or extend these instructions to HT 70 or later configurations. No production serial is supplied by this bulletin.
TI dependency: TI 14/1999, p. 6 — 2.4 delegated chain-tensioner reference; later manual section 7.2 and lubricating-grease row of 10.2 only.
Later manual evidence: E 140, E 160, E 180 C service manual (2003-01), section 1, 4.1 (cover removal only), 7.2 and 10.2 (later edition; side tensioner and lubricating-grease row), PDF pages 1, 3, 7, 18, 24
No parts-table entry added. Tool references, where present, are retained in the manual notes above.
Wrong number or missing part for the HT 70, HT 75? Report a correction →