Stihl 4140 · Section R · 17 of 23 · 36 parts
Carburetor C1Q-S66 (36.2002)
Fits FS 38, FS 45, FS 45 C, FS 45 L, FS 46, FS 46 C.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (36)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4137 120 7100 | Throttle shaft with lever | 1 |
| 2 | 1123 122 3000 | Spring | 1 |
| 3 | 4137 121 8900 | Pin → replaced by 4128 121 8900 TI 41/1997 | 1 |
| 4 | 4137 121 8600 | Washer | 1 |
| 5 | 1120 122 9000 | E-clip | 1 |
| 6 | 4140 121 3302 NLA | Throttle shutter | 1 |
| 7 | 1125 122 7403 | Round head screw | 1 |
| 8 | 1125 122 9001 | E-clip | 1 |
| 9 | 1129 121 4800 | Pump diaphragm Fitment / change note → | 1 |
| 10 | 1123 129 0905 | Gasket Fitment / change note → | 1 |
| 11 | 1123 121 0800 | End cover | 1 |
| 12 | 1120 122 7800 | Oval head screw | 1 |
| 13 | 4116 121 5100 | Inlet needle | 1 |
| 14 | 1120 122 3004 | Spring | 1 |
| 15 | 1125 121 5000 | Inlet control lever | 1 |
| 16 | 1120 121 9200 | Spindle | 1 |
| 17 | 1120 122 6600 | Collar screw | 1 |
| 18 | 1129 129 0900 | Gasket Fitment / change note → → replaced by 4134 121 4700 TI 16/2009 | 1 |
| 19 | 4129 121 4700 | Metering diaphragm Fitment / change note → | 1 |
| 20 | not sold separately | Flange not available as a separate item | 1 |
| 21 | 4226 122 7100 | Screw | 4 |
| 22 | 4229 122 6700 | High speed adjustment screw | 1 |
| 23 | 4229 122 6800 | Low speed adjustment screw | 1 |
| 24 | 1123 121 7800 | Strainer | 1 |
| 25 | 4140 121 0800 | End cover | 1 |
| 26 | 4226 121 2700 | Cap | 1 |
| 27 | 4229 122 6200 | Idle speed adjustment screw | 1 |
| 28 | 1125 122 4200 | Clamp | 1 |
| 29 | 4229 121 2700 | Cap | 1 |
| 30 | 4229 121 5603 | Fixed jet 0.37 | 1 |
| 31 | 4229 121 5800 | Pump piston | 1 |
| 32 | 4140 122 3600 | Sealing ring → replaced by 4314 122 3600 TI 20/2008 | 1 |
| 33 | 4229 122 3001 | Spring | 1 |
| 34 | 1120 121 7801 | Strainer | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4140 120 0603 NLA | Carburetor C1Q-S66 Fitment / change note → → replaced by 4140 120 0606 TI 36/2002 | 1 |
| — | 1129 007 1062 | Set of carburetor parts → replaced by 4128 007 1060, 4128 007 1060 TI 6/2009 | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · HL 45 / FC 55 / FS 55 / FS 45
HL 45, FC 55, FS 45/55: C1Q-S66 limiter and service settings
Three-screw carburetor replaces LD/BIS; uncapped workshop settings and capped user adjustment are distinct.
- Only the named HL 45, FC 55, FS 55 and FS 45 configurations are covered. Shared IPL sheets do not extend this note to FS 38/46 or unnamed C/L/R/RC/T variants. The HL 45 header says series 4232; 4140 powerhead navigation is not a series-equivalence claim.
- The update aims to improve function/reliability and comply with new emission regulations; these are source claims, not measured results. C1Q-S58 4140 120 0610 (BIS = Balanced Idle System, LD screw) is replaced by C1Q-S66 4140 120 0603 with H, L and LA screws. The older carburetor remains listed for older machines/other models. The TI refers component parts to the IPL; the four named-model C1Q-S66 sheets in SCS01-2012 USA are now reviewed against raw catalog rows and common drawing392ET046. This later edition is not an exact2001 parts-list edition.
- The H limiter cap fits over the knurled H screw; a body stop pin limits rotation to 3/4 turn (270 degrees). Funnel-shaped L and LA caps guide the screwdriver; the TI does not describe them as mixture limiters.
- For replacement of a damaged H screw or carburetor cleaning, pull off the H cap with suitable pliers. Removed caps are damaged and must not be reused. Before adjustment check the air filter, spark-arresting screen and fuel filter; clean or replace as necessary.
- Historical workshop standard with cap removed: from lightly seated, open H 1 1/2 turns. Align a NEW cap with the rich stop and push it home against the carburetor body. Do not silently substitute a later short-cap detent instruction.
- From lightly seated, open L one full turn counterclockwise; use LA to set 2,800 RPM and check with a tachometer. Check smooth acceleration by opening the throttle several times, and smooth idle. These are the TI settings for this configuration, not a universal live-machine procedure.
- Users have only the capped 270-degree H range, allowing a leaner setting if necessary at altitude; H normally remains at the rich stop. Section2.1.9 delegates the full procedure to the model owner manual, Adjusting the Carburetor. Exact HL45, FC55, FS45 and FS55 owner-manual editions remain unavailable in the bounded retained inventory; this is a documented source gap, not substituted by a workshop manual.
- Later retained evidence: Components4140 RA241 (2003-10), printed45–48, keeps the cap for standard H adjustment to the counterclockwise stop (no more than3/4turn); uncapped basic H1 1/2turns and L1turn are distinct. A short cap seats only at the second noticeable detent and must not touch the body; a long cap seats against the body. Both align with the rich stop and removed caps must not be reused. Do not silently apply one cap procedure to the other. The later IPL lists H screw4229 122 6700 and cap4229 121 2700; its reference-only flange has no order number. TI36/2002 supplies the later shorter-H carburetor and required matched flange-kit rule. No unproven cap pairing or historical supersession is inferred. See docs/ti27-2001-dependencies.md.
- Introduction of the overall model update is in progress, not a dated universal serial cutoff. Availability is historical 2001 factory supply, not current stock. No hardware fitment or operation was tested.
Source: TI 27/2001, p. 2 · TI 27/2001, p. 3 · TI 27/2001, p. 4 · TI 27/2001, p. 7 · TI 27/2001, p. 8 — Sections2–2.1.9 and summary rows1–2, remarks1–2.
Part numbers (2)
- 4140 120 0610 — C1Q-S58 LD carburetorPrevious; retained for older machines/other models · HL 45, FC 55, FS 55, FS 45; source configuration restrictions apply
- 4140 120 0603 — C1Q-S66 H/L/LA carburetorNew; configuration-specific settings · HL 45, FC 55, FS 55, FS 45; source configuration restrictions apply
Conditional replacement · HL 45 / FC 55 / FS 45 / FS 55 / KM 55
HL 45, FC 55, FS 45/55, KM 55: shorter-H carburetor and matched flange kit
New carburetor and a mandatory flange/diaphragm/gasket combination for repairs to the previous carburetor.
- Only the named HL 45, FC 55, FS 45, FS 55 and KM 55 configurations are covered, with the section-specific HL 45 exclusion below where stated. Shared IPL sheets do not extend this note to FS 38/46 or unnamed C/L/R/RC/T variants. HL 45 is headed series 4232; navigation through 4140 powerhead sheets is not series equivalence.
- Carburetor 4140 120 0603 is replaced by 4140 120 0606 with a shorter high-speed screw H. The press-fitted H cap is limited to 270 degrees (3/4 turn) by a stop between H and L. L and LA screws are separately identified. The TI does not give replacement H-screw/cap part numbers or a cap interchange rule.
- Flange, gasket and metering-diaphragm shapes change. The source describes increased flange strength and a symmetrical gasket to prevent incorrect installation; these are source design claims, not measured results.
- If flange 4140 120 2200 must be replaced on an existing 4140 120 0603 carburetor, install flange 4228 120 2200 together with metering diaphragm 4229 121 4700 and gasket 4229 129 0901 from kit 4140 007 1060. This is a required matched combination, not permission to fit the new flange alone.
- The kit includes summary items3–7: new flange 4228 120 2200, gasket 4229 129 0901 and metering diaphragm 4229 121 4700, plus unchanged pump diaphragm 1129 121 4800 and gasket 1123 129 0905. The narrative describes flange, metering diaphragm and two gaskets; the summary also explicitly includes the pump diaphragm. Preserve the full summary roster.
- Previous carburetor 4140 120 0603 is no longer available from the factory. Previous flange 4140 120 2200 remains for other models; previous gasket 1129 129 0900 and metering diaphragm 4129 121 4700 remain as spares. Retention does not override the mandatory repair combination.
- Maintenance/repair refers to TI27/2001, now reviewed with exact owner-edition source gaps. Later Components4140 manual RA241 (2003-10, printed45–48) distinguishes capped standard adjustment from uncapped basic adjustment and short-cap second-detent from long-cap body seating. Do not press a short cap against the body or infer its part-number pairing from screw length alone. See docs/ti27-2001-dependencies.md for pinned evidence and limits.
- Introduction is in progress, with no numerical serial cutoff. Factory availability is the historical 2002 statement, not current stock. Later IPL numbers do not overwrite historical numbers or prove unrestricted interchangeability. No hardware operation or fitment was tested.
Source: TI 36/2002, p. 1 · TI 36/2002, p. 2 · TI 36/2002, p. 3 — Sections1–1.5, all carburetor diagrams and summary rows1–7/remarks1–3.
Part numbers (11)
- 4140 120 0603 — CarburetorPrevious; factory supply ended · Named models only; section-specific restrictions apply
- 4140 120 0606 — Shorter-H-screw carburetorNew · Named models only; section-specific restrictions apply
- 4140 007 1060 — Carburetor parts kitIncludes summary items3–7 · Named models only; section-specific restrictions apply
- 4140 120 2200 — FlangePrevious; other models · Named models only; section-specific restrictions apply
- 4228 120 2200 — FlangeRequired matched repair set · Named models only; section-specific restrictions apply
- 1129 129 0900 — Metering gasketPrevious; retained · Named models only; section-specific restrictions apply
- 4229 129 0901 — Metering gasketRequired matched repair set · Named models only; section-specific restrictions apply
- 4129 121 4700 — Metering diaphragmPrevious; retained · Named models only; section-specific restrictions apply
- 4229 121 4700 — Metering diaphragmRequired matched repair set · Named models only; section-specific restrictions apply
- 1129 121 4800 — Pump diaphragmUnchanged; included · Named models only; section-specific restrictions apply
- 1123 129 0905 — Pump-side gasketUnchanged; included · Named models only; section-specific restrictions apply
Wrong number or missing part for the FS 38, FS 45, FS 45 C, FS 45 L, FS 46, FS 46 C? Report a correction →