Stihl 4140 · Section N · 13 of 19 · 37 parts
Carburetor C1Q-S66 (36.2002)
Fits KM 55, KM 55 C, KM 55 R, KM 55 RC.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (37)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4137 120 7100 | Throttle shaft with lever | 1 |
| 2 | 1123 122 3000 | Spring | 1 |
| 3 | 4137 121 8900 | Pin → replaced by 4128 121 8900 TI 41/1997 | 1 |
| 4 | 4137 121 8600 | Washer | 1 |
| 5 | 1120 122 9000 | E-clip | 1 |
| 6 | 4140 121 3302 NLA | Throttle shutter | 1 |
| 7 | 1125 122 7403 | Round head screw | 1 |
| 8 | 1125 122 9001 | E-clip | 1 |
| 9 | 1129 121 4800 | Pump diaphragm Fitment / change note → | 1 |
| 10 | 1123 129 0905 | Gasket Fitment / change note → | 1 |
| 11 | 1123 121 0800 | End cover | 1 |
| 12 | 1120 122 7800 | Oval head screw | 1 |
| 13 | 4116 121 5100 | Inlet needle | 1 |
| 14 | 1120 122 3004 | Spring | 1 |
| 15 | 1125 121 5000 | Inlet control lever | 1 |
| 16 | 1120 121 9200 | Spindle | 1 |
| 17 | 1120 122 6600 | Collar screw | 1 |
| 18 | 1129 129 0900 | Gasket Fitment / change note → → replaced by 4134 121 4700 TI 16/2009 | 1 |
| 19 | 4129 121 4700 | Metering diaphragm Fitment / change note → | 1 |
| 20 | not sold separately | Flange not available as a separate item | 1 |
| 21 | 4226 122 7100 | Screw | 4 |
| 22 | 4229 122 6700 | High speed adjustment screw | 1 |
| 23 | 4229 122 6800 | Low speed adjustment screw | 1 |
| 24 | 1123 121 7800 | Strainer | 1 |
| 25 | 4140 121 0800 | End cover | 1 |
| 26 | 4226 121 2700 | Cap | 1 |
| 27 | 4229 122 6200 | Idle speed adjustment screw | 1 |
| 28 | 1125 122 4200 | Clamp | 1 |
| 29 | 4229 121 2700 | Cap | 1 |
| 30 | 4229 121 5603 | Fixed jet 0.37 | 1 |
| 31 | 4229 121 5800 | Pump piston | 1 |
| 32 | 4140 122 3600 | Sealing ring → replaced by 4314 122 3600 TI 20/2008 | 1 |
| 33 | 4229 122 3001 | Spring | 1 |
| 34 | 1120 121 7801 | Strainer | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4140 120 0603 NLA | Carburetor C1Q-S66 Fitment / change note → → replaced by 4140 120 0606 TI 36/2002 | 1 |
| — | 4140 007 1060 | Set of carburetor parts Fitment / change note → | 1 |
| — | 1129 007 1062 | Set of carburetor parts → replaced by 4128 007 1060, 4128 007 1060 TI 6/2009 | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · HL 45 / FC 55 / FS 45 / FS 55 / KM 55
HL 45, FC 55, FS 45/55, KM 55: shorter-H carburetor and matched flange kit
New carburetor and a mandatory flange/diaphragm/gasket combination for repairs to the previous carburetor.
- Only the named HL 45, FC 55, FS 45, FS 55 and KM 55 configurations are covered, with the section-specific HL 45 exclusion below where stated. Shared IPL sheets do not extend this note to FS 38/46 or unnamed C/L/R/RC/T variants. HL 45 is headed series 4232; navigation through 4140 powerhead sheets is not series equivalence.
- Carburetor 4140 120 0603 is replaced by 4140 120 0606 with a shorter high-speed screw H. The press-fitted H cap is limited to 270 degrees (3/4 turn) by a stop between H and L. L and LA screws are separately identified. The TI does not give replacement H-screw/cap part numbers or a cap interchange rule.
- Flange, gasket and metering-diaphragm shapes change. The source describes increased flange strength and a symmetrical gasket to prevent incorrect installation; these are source design claims, not measured results.
- If flange 4140 120 2200 must be replaced on an existing 4140 120 0603 carburetor, install flange 4228 120 2200 together with metering diaphragm 4229 121 4700 and gasket 4229 129 0901 from kit 4140 007 1060. This is a required matched combination, not permission to fit the new flange alone.
- The kit includes summary items3–7: new flange 4228 120 2200, gasket 4229 129 0901 and metering diaphragm 4229 121 4700, plus unchanged pump diaphragm 1129 121 4800 and gasket 1123 129 0905. The narrative describes flange, metering diaphragm and two gaskets; the summary also explicitly includes the pump diaphragm. Preserve the full summary roster.
- Previous carburetor 4140 120 0603 is no longer available from the factory. Previous flange 4140 120 2200 remains for other models; previous gasket 1129 129 0900 and metering diaphragm 4129 121 4700 remain as spares. Retention does not override the mandatory repair combination.
- Maintenance/repair refers to TI27/2001, now reviewed with exact owner-edition source gaps. Later Components4140 manual RA241 (2003-10, printed45–48) distinguishes capped standard adjustment from uncapped basic adjustment and short-cap second-detent from long-cap body seating. Do not press a short cap against the body or infer its part-number pairing from screw length alone. See docs/ti27-2001-dependencies.md for pinned evidence and limits.
- Introduction is in progress, with no numerical serial cutoff. Factory availability is the historical 2002 statement, not current stock. Later IPL numbers do not overwrite historical numbers or prove unrestricted interchangeability. No hardware operation or fitment was tested.
Source: TI 36/2002, p. 1 · TI 36/2002, p. 2 · TI 36/2002, p. 3 — Sections1–1.5, all carburetor diagrams and summary rows1–7/remarks1–3.
Part numbers (11)
- 4140 120 0603 — CarburetorPrevious; factory supply ended · Named models only; section-specific restrictions apply
- 4140 120 0606 — Shorter-H-screw carburetorNew · Named models only; section-specific restrictions apply
- 4140 007 1060 — Carburetor parts kitIncludes summary items3–7 · Named models only; section-specific restrictions apply
- 4140 120 2200 — FlangePrevious; other models · Named models only; section-specific restrictions apply
- 4228 120 2200 — FlangeRequired matched repair set · Named models only; section-specific restrictions apply
- 1129 129 0900 — Metering gasketPrevious; retained · Named models only; section-specific restrictions apply
- 4229 129 0901 — Metering gasketRequired matched repair set · Named models only; section-specific restrictions apply
- 4129 121 4700 — Metering diaphragmPrevious; retained · Named models only; section-specific restrictions apply
- 4229 121 4700 — Metering diaphragmRequired matched repair set · Named models only; section-specific restrictions apply
- 1129 121 4800 — Pump diaphragmUnchanged; included · Named models only; section-specific restrictions apply
- 1123 129 0905 — Pump-side gasketUnchanged; included · Named models only; section-specific restrictions apply
Wrong number or missing part for the KM 55, KM 55 C, KM 55 R, KM 55 RC? Report a correction →