← Cut-off machines · series 4201

Stihl 4201 · Section B · 2 of 20 · 32 parts

Cylinder, Muffler

Fits TS 350 AVE, TS 360.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

This drawing carries 2 bore sizes — Ø 47 mm , Ø 49 mm . Not interchangeable — measure your cylinder before ordering. The catalogue lists them on one sheet for one machine and never says which variant each belongs to, so this guide does not either.

Position —

Go to table row → Where else is this used →
110111213141516161718192202122222324252627282933044556789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (32)

PosPart numberDescriptionQty
1 4201 020 1200 Cylinder with piston Ø 49 mm 1
2 4201 030 2000 Piston Ø 49 mm 1
3 1127 034 3007 Piston ring Ø 49x1.5 mm 2
4 1108 034 1501 Piston pin 12x8x33 1
5 9463 650 1200 Snap ring 12x1 2
6 1108 020 1220 Cylinder with piston Ø 47 mm 1
7 1108 030 2020 Piston Ø 47 mm 1
8 1108 034 3001 Piston ring Ø 47x1.5 mm 1
9 9512 003 3140 Needle cage 12x16x13 1
10 1108 029 2300 Cylinder gasket 1
11 9022 341 1300 Spline screw IS-M6x20 4
12 0000 400 7000 Spark plug NGK BPMR7A 1
12 1110 400 7005 Spark plug Bosch WSR 6 F 1
13 4201 405 1000 Spark plug boot 1
14 0000 998 0603 Torsion spring → replaced by 0000 998 0604 TI 30/1995 1
15 9121 347 1370 Stud M6x30 Fitment / change note → 1
16 1108 149 0600 Muffler gasket 2
17 4201 141 1500 Flange 1
18 4201 140 0607 NLA Muffler Fitment / change note → 1
19 4201 141 9001 NLA Screen Fitment / change note → 1
20 9022 313 0610 Spline screw IS-M4x6 Fitment / change note → 1
21 9022 341 1350 Spline screw IS-M6x25 Fitment / change note → 2
22 9206 160 0900 Collar nut M6 Fitment / change note → 2
23 9099 021 0810 Self-tapping screw 4.2x9.5 Fitment / change note → 1
24 4201 148 3001 Shim Fitment / change note → 1
25 9022 341 1520 Spline screw IS-M6x90 Fitment / change note → 2
26 4201 140 7200 Muffler guard 1
27 9416 868 7030 Hollow rivet 7x0.5x6.8 1
28 9022 341 1310 Spline screw IS-M6x18 1
29 9008 319 1010 Hexagon head screw M5x18 1
30 9307 021 0120 Washer 5.3 1
Not numbered on the diagram — assemblies, kits and options
— 4201 007 1050 NLA Set of gaskets option 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · TS 350 / TS 360

TS 350 / TS 360: complete replacement muffler and mounting hardware

European and USA/CDN/AUS mufflers consolidate into complete 4201 140 0607, with spark screen and revised fasteners.

X 28 323 087 — Introduction of this specific modification on the named models; not a production range or interchange guarantee.

  • From X 28 323 087, TWO IS M6x25 screws replace TWO IS M6x90x30 screws. Higher-strength stud 9121 347 1370 replaces 0000 953 1024; TWO new M6 flange nuts have larger flanges. Cover plate and spark-arresting screen each use ONE IS M4x6 screw (TWO total). The old B4.2x9.5 screen screw and long-screw strap are deleted from the new arrangement.
  • Original European muffler 4201 140 0601 and USA/CDN/AUS muffler 4201 140 0605 are no longer factory-available. Only the new complete muffler is supplied as a replacement, with screen and necessary mounting hardware to ensure interchangeability. In countries requiring a spark screen, fit it according to the illustrated instructions supplied with the assembly; this TI is not a complete installation procedure or current legal determination.
  • The table lists complete muffler as including item 1 and items 3–6; stud is separately item 7. Preserve that printed inclusion boundary rather than asserting item 7 is explicitly listed inside the kit. Screen number 4201 141 9001 is unchanged; welded cover plate becomes separately secured plate 4201 146 7300.
  • Deleted B4.2x9.5 screw, long screws and strap, and original flange nut and stud remain available for older machines and other models under remark 2. Their removal from the new arrangement is not global discontinuation.
  • Historical TI09/1994 guidance for the named TS 350 / TS 360 models only; no successor or TS 350 AVE applicability inferred from a shared IPL sheet. Across-flats dimensions describe wrench sizes, not thread diameters. Factory stock statements are historical, not current availability. MOQ columns are commercial order quantities. No physical interchange test was performed.

Source: TI 9/1994, p. 2 · TI 9/1994, p. 3 — TS 350 / TS 360: complete replacement muffler and mounting hardware.

Part numbers (14)
  • 4201 140 0601 — European muffleroriginal; no longer supplied · TS 350 / TS 360: complete replacement muffler and mounting hardware
  • 4201 140 0605 — USA/CDN/AUS muffleroriginal; no longer supplied · TS 350 / TS 360: complete replacement muffler and mounting hardware
  • 4201 140 0607 — Complete mufflernew assembly · TS 350 / TS 360: complete replacement muffler and mounting hardware
  • 4201 141 9001 — Spark screen, key 1unchanged number · TS 350 / TS 360: complete replacement muffler and mounting hardware
  • 9099 021 0810 — B4.2x9.5 screw, key 2deleted here; retained elsewhere · TS 350 / TS 360: complete replacement muffler and mounting hardware
  • 9022 341 1520 — IS M6x90x30 screws, twodeleted here; retained elsewhere · TS 350 / TS 360: complete replacement muffler and mounting hardware
  • 4201 148 3001 — Long-screw strapdeleted here; retained elsewhere · TS 350 / TS 360: complete replacement muffler and mounting hardware
  • 4201 146 7300 — Cover plate, key 3new separate plate · TS 350 / TS 360: complete replacement muffler and mounting hardware
  • 9022 313 0610 — IS M4x6 screws, two, key 4new fasteners · TS 350 / TS 360: complete replacement muffler and mounting hardware
  • 9022 341 1350 — IS M6x25 screws, two, key 5new fasteners · TS 350 / TS 360: complete replacement muffler and mounting hardware
  • 9220 260 0901 — M6 flange nutoriginal; retained elsewhere · TS 350 / TS 360: complete replacement muffler and mounting hardware
  • 9206 160 0900 — M6 flange nuts, two, key 6new larger flange · TS 350 / TS 360: complete replacement muffler and mounting hardware
  • 0000 953 1024 — M6x30 studoriginal; retained elsewhere · TS 350 / TS 360: complete replacement muffler and mounting hardware
  • 9121 347 1370 — M6x30 stud, key 7new higher strength · TS 350 / TS 360: complete replacement muffler and mounting hardware

Service note · TS 350 / TS 360

TS 350 / TS 360: muffler-stud drawing rejects 18 mm threaded segment

Scan330TI010KN crosses out 18 mm (45/64 inch) and shows 21 mm (53/64 inch).

  • Contents lists section 3, Muffler (stud). Page 2 lower-right drawing 330TI010 KN supplies its evidence without a prose section heading or parts table: the upper stud is crossed out, with the left threaded segment dimension 18 mm (45/64 inch); the lower, uncrossed stud has that segment dimension 21 mm (53/64 inch). Both printed metric/inch pairs are retained.
  • Dimension extension lines run from the LEFT END to the END OF THE LEFT THREADED SEGMENT, not end-to-end across the whole stud. The drawing must not become an 18→21 mm overall stud length, installed protrusion, insertion depth or hole-depth specification.
  • The drawing points to the muffler mounting location. With no adjacent model-specific label, the bulletin header TS 350/TS 360 is retained as document scope; this is scan-only service evidence, not independently verified identical mounting geometry on both models. No stud part number, thread pitch, overall length, torque, locking compound, installation direction or changeover serial is printed.
  • Neither starter X 32 180 714 nor the two nameplate serials is assigned to this drawing. The absence of a prose heading is not proof that a third page exists; the retained and mounted inventories have two pages. No unstated stud replacement ordering number is invented. Imprint and blank page space add no applicability.
  • Historical TI 10/1996 evidence for TS 350 and TS 360, series 4201. Shared catalog sheets do not add TS 350 AVE, TS 510 or TS 760. No hardware operation was performed; factory availability is historical, not current stock. Starter and the two model-specific nameplate changeovers must remain separate.

Source: TI 10/1996, p. 2 — TS 350 / TS 360: muffler-stud drawing rejects 18 mm threaded segment.

No additional parts-table entry added.

Wrong number or missing part for the TS 350 AVE, TS 360? Report a correction →