← Cut-off machines · series 4201

Stihl 4201 · Section C · 3 of 20 · 23 parts

Clutch, Pick-up body

Fits TS 350 AVE, TS 360.

Parts diagrams →

Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151617181922021223456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (23)

PosPart numberDescriptionQty
1 1106 029 8900 Insulating rod 1
2 1108 162 8901 Washer 1
3 1108 162 3201 Carrier 1
4 1108 160 1501 Clutch shoe 3
5 0000 997 5811 Tension spring 3
6 1108 162 8911 Washer 1
7 4201 700 2506 V-belt pulley Fitment / change note → 1
8 9529 003 4181 Needle cage 1516 2 Fitment / change note → 1
9 0000 993 0510 Ring 1
10 4201 958 1000 Washer 1
11 9211 260 1350 Hexagon nut M10x1 l/h thread 1
12 1108 358 7702 Hose 1
13 0000 350 3500 Pickup body Fitment / change note → 1
14 1108 353 2500 Elbow connector 1
15 1106 358 0700 Hose 135mm 1
16 4201 007 1032 Elbow connector kit Fitment / change note → 1
17 9645 948 4050 O-ring 36x3 → replaced by 9645 951 3890 TI 34/2006 1
18 4104 359 0700 Gasket Fitment / change note →
19 1107 350 0500 Filler cap 1
20 9645 948 4050 O-ring 36x3 → replaced by 9645 951 3890 TI 34/2006 1
21 1117 350 0905 Filler cap retainer 1
22 9099 021 2360 Self-tapping screw 3.5x9.5 1
Not numbered on the diagram — assemblies, kits and options
— 1108 160 2001 NLA Clutch 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · TS 350 / TS 360

TS 350 / TS 360: fuel-tank elbow packing depends on tank revision

Thread-runout change removes packing gaskets on revised tanks, but replacement elbow still includes three for older machines.

X 27 928 356 — Printed introduction for this component change only; not a universal production range or interchange guarantee.

  • From X 27 928 356, modified thread runout in the FUEL TANK makes packing gaskets 4104 359 0700 unnecessary. This is not a blanket instruction to remove gaskets from older tanks.
  • As before, screw elbow fitting 4201 007 1032 in to the stop until the retaining lugs engage. O-ring 9645 945 4050 seals in that position. Replacement elbow is supplied with THREE gaskets for use on older machines; gasket 4104 359 0700 remains available for older machines. No new elbow number, torque or unrestricted tank interchange is stated.
  • Historical TI 09/1994 guidance for the explicitly named models only; no TS 350 AVE or successor applicability inferred from shared IPL sheets. Factory supply statements are historical. MOQ values are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 9/1994, p. 7 — TS 350 / TS 360: fuel-tank elbow packing depends on tank revision.

Part numbers (3)
  • 4104 359 0700 — Packing gasketunnecessary on revised tank; retained for older machines · TS 350 / TS 360: fuel-tank elbow packing depends on tank revision
  • 4201 007 1032 — Elbow fitting with three gasketsreplacement for older and revised tank context · TS 350 / TS 360: fuel-tank elbow packing depends on tank revision
  • 9645 945 4050 — O-ringjoint seal at engaged stop · TS 350 / TS 360: fuel-tank elbow packing depends on tank revision

Service note · TS 350 / TS 360

TS 350 / TS 360: larger-strainer pickup and separate spare limits

Complete pickup changes to 0000 350 3500; the original filter remains a spare but the new filter is not separately available.

X 29 360 506 — Printed introduction for this component change only; not a universal production range or interchange guarantee.

  • From X 29 360 506, pickup 0000 350 3500 replaces 1115 350 3503, with larger strainer for longer service life and better filtration according to the source. Original complete pickup is no longer factory-available. Standardization across several models does not name additional fitment.
  • Original filter 1110 358 1800 (drawing 1) REMAINS available for older machines; the new filter is NOT available separately. Original weight 1115 358 2500 (2) and cap 1115 358 8200 (3) are supplied only while factory stocks last. The exploded left-hand drawing shows ORIGINAL pickup internals; the right-hand view shows the new pickup. Do not infer internal interchange or a separately replaceable new filter.
  • Historical TI 09/1994 guidance for the explicitly named models only; no TS 350 AVE or successor applicability inferred from shared IPL sheets. Factory supply statements are historical. MOQ values are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 9/1994, p. 10 · TI 9/1994, p. 11 — TS 350 / TS 360: larger-strainer pickup and separate spare limits.

Part numbers (5)
  • 1115 350 3503 — Complete pickup bodyoriginal; no longer supplied · TS 350 / TS 360: larger-strainer pickup and separate spare limits
  • 0000 350 3500 — Complete larger-strainer pickupnew · TS 350 / TS 360: larger-strainer pickup and separate spare limits
  • 1110 358 1800 — Original filter, item 1retained for older machines; new filter not separate · TS 350 / TS 360: larger-strainer pickup and separate spare limits
  • 1115 358 2500 — Original weight, item 2while stocks last · TS 350 / TS 360: larger-strainer pickup and separate spare limits
  • 1115 358 8200 — Original cap, item 3while stocks last · TS 350 / TS 360: larger-strainer pickup and separate spare limits

Service note · TS 350 / TS 360

TS 350 / TS 360: pulley needle sleeve gets heat-resistant sealing lips

9529 003 4181 replaces 9529 003 4180; complete pulley number stays 4201 700 2506.

X 29 422 266 — Printed introduction for this component change only; not a universal production range or interchange guarantee.

  • From X 29 422 266, needle sleeve 2 RS 9529 003 4181 replaces 9529 003 4180 with sealing lips made of more heat-resistant material. Original sleeve remains factory-supplied only while stocks last.
  • Complete V-belt pulley 4201 700 2506 keeps its number; only the modified pulley is factory-available. The note separately extends the needle-sleeve line modification to TS 510 and TS 760, but does not establish that those machines share this complete pulley number. Last TI 47/1990 pointer and February 21, 1994 issue date are source context, not review of that earlier TI.
  • Historical TI 09/1994 guidance for the explicitly named models only; no TS 350 AVE or successor applicability inferred from shared IPL sheets. Factory supply statements are historical. MOQ values are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 9/1994, p. 11 — TS 350 / TS 360: pulley needle sleeve gets heat-resistant sealing lips.

Part numbers (3)
  • 4201 700 2506 — Complete V-belt pulleyunchanged number; modified version only · TS 350 / TS 360: pulley needle sleeve gets heat-resistant sealing lips
  • 9529 003 4180 — Needle sleeve 2 RSoriginal; while stocks last · TS 350 / TS 360: pulley needle sleeve gets heat-resistant sealing lips
  • 9529 003 4181 — Needle sleeve 2 RSnew heat-resistant sealing lips · TS 350 / TS 360: pulley needle sleeve gets heat-resistant sealing lips

Wrong number or missing part for the TS 350 AVE, TS 360? Report a correction →