Stihl 4201 · Section K · 10 of 24 · 38 parts
Carburetor HS-277A
Fits TS 510, TS 760.
Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.
Parts (38)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1110 122 9410 | Plug | 1 |
| 2 | 1110 122 3020 | Spring | 1 |
| 3 | 1110 121 5100 | Inlet needle | 1 |
| 4 | 1124 121 5000 | Inlet control lever | 1 |
| 5 | 1110 121 9200 | Spindle | 1 |
| 6 | 1110 122 7801 | Oval head screw | 1 |
| 7 | 1111 121 5400 | Valve jet | 1 |
| 8 | 1110 129 0900 | Gasket | 1 |
| 9 | 1110 121 4700 | Metering diaphragm | 1 |
| 10 | 1106 122 7400 | Round head screw Fitment / change note → | 4 |
| 11 | 4205 121 0800 | End cover Fitment / change note → | 1 |
| 12 | 4221 121 7800 | Strainer Fitment / change note → | 1 |
| 13 | 4223 122 3600 | Sealing ring Fitment / change note → | 2 |
| 14 | 1110 122 3030 | Spring Fitment / change note → | 2 |
| 15 | 4205 122 6700 | High speed adjustment screw Fitment / change note → | 1 |
| 16 | 4205 122 6800 | Low speed adjustment screw Fitment / change note → | 1 |
| 17 | 4221 122 4200 | Ball Fitment / change note → | 1 |
| 18 | 4221 122 6200 | Idle speed adjustment screw Fitment / change note → | 1 |
| 19 | 4205 120 7200 | Choke shaft with lever Fitment / change note → | 1 |
| 20 | 4205 122 3200 | Torsion spring Fitment / change note → | 1 |
| 21 | 4221 121 9400 | Ring Fitment / change note → | 2 |
| 22 | 4221 122 3605 | Sealing ring Fitment / change note → | 2 |
| 23 | 1110 122 9005 | E-clip Fitment / change note → | 2 |
| 24 | 4221 120 7100 | Throttle shaft with lever Fitment / change note → | 1 |
| 25 | 4221 122 9100 | Bushing Fitment / change note → | 2 |
| 26 | 4221 122 3200 | Torsion spring Fitment / change note → | 1 |
| 27 | 4221 121 8600 | Washer Fitment / change note → | 1 |
| 28 | 4205 120 8705 | Control valve Fitment / change note → | 1 |
| 29 | 1110 129 3000 | Sealing ring | 1 |
| 30 | 1110 121 4800 | Pump diaphragm | 1 |
| 31 | 1110 129 1110 | Gasket | 1 |
| 32 | 1110 121 0815 | End cover | 1 |
| 33 | 1110 122 7700 | Oval head screw | 4 |
| 34 | 1115 121 2900 | Choke shutter | 1 |
| 35 | 1110 122 7400 | Round head screw Fitment / change note → | 2 |
| 36 | 1115 121 3300 | Throttle shutter | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4205 120 0601 | Carburetor HS-277A Fitment / change note → → replaced by 4205 120 0602 TI 7/1998 | 1 |
| — | 1115 007 1060 | Set of carburetor parts | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · TS 510 / TS 760
TS 510 / TS 760: compensator hose and choke changes
Clean-side filter pressure reaches the metering diaphragm through a shaped hose.
- Section 1: shaped hose 4205 122 4000 connects the CLEAN SIDE of the air filter to the OUTSIDE of the carburetor metering diaphragm. This compensator connection is distinct from the tank-vent hose introduced in section 3; do not join them by an assumed common purpose.
- The source describes keeping the proportion of fuel constant as the filter becomes dirty, delaying power reduction. It does not claim unchanged power indefinitely or eliminate filter maintenance. System introduction is X 24 097 471.
- Table items 18–20: choke lever 1111 185 2000 → 1111 185 2001; spring 0000 997 0326 → 1108 122 3001; hose 4205 122 4000 is added. The old choke lever is supplied only UNTIL STOCKS ARE EXHAUSTED (remark 3); the old spring remains an older-machine spare (remark 1). Do not apply one availability policy to both.
- The external choke lever and its spring are not the same table positions as the carburetor choke shaft, torsion spring or removed internal detent spring. Follow drawing 328TI011 and the separate carburetor table.
- Historical TI26/1996 guidance for TS 510 and TS 760 only. Source type 4205 is bound to exact named-model sheets consolidated under 4201, not a general series equivalence. TS 460 is a design comparison, not added fitment. Factory availability is historical, not a current stock guarantee. No hardware operation was performed.
Source: TI 26/1996, p. 1 · TI 26/1996, p. 2 · TI 26/1996, p. 3 — TS 510 / TS 760: compensator hose and choke changes.
Part numbers (5)
- 1111 185 2000 — Choke leverOriginal; stock exhaustion · TS 510 / TS 760; TS 510 / TS 760: compensator hose and choke changes
- 1111 185 2001 — Choke leverNew · TS 510 / TS 760; TS 510 / TS 760: compensator hose and choke changes
- 0000 997 0326 — Choke lever springOriginal; older-machine spare · TS 510 / TS 760; TS 510 / TS 760: compensator hose and choke changes
- 1108 122 3001 — Choke lever springNew in filter-system table · TS 510 / TS 760; TS 510 / TS 760: compensator hose and choke changes
- 4205 122 4000 — Shaped compensator hoseNew; clean-side pressure connection · TS 510 / TS 760; TS 510 / TS 760: compensator hose and choke changes
Historical fitment · TS 510 / TS 760
TS 510 / TS 760: HS 277 A replaces HS 212 B in production
The carburetor and filter change share X 24 097 471, not the earlier ignition cutoff.
- Section 2: original 4205 120 0600 (HS 212 B) is replaced by 4205 120 0601 (HS 277 A) with introduction of the new filter system from X 24 097 471. The original complete carburetor remains available for older machines under remark 1. This is a production replacement statement, not blanket standalone retrofit permission.
- The HS 277 A has a compensator connection, O-ring-sealed H/L adjusting screws with standardized springs and an idle speed screw in the carburetor body. Choke shaft, throttle shaft, control valve and listed components also change. Page 5 says ALL OTHER PARTS ARE IDENTICAL IN BOTH CARBURETORS; that does not make the explicitly changed components interchangeable.
- Page 4 separately dates ignition speed limiting to X 24 073 218 (TI33/1995). Do not move that earlier ignition event to X 24 097 471 or treat every electronically governed machine as HS 277 A-equipped.
- Later HS-212B sheet L has parsed from_serial 24097470, which conflicts with reading it as the start of the old carburetor. Preserve the canonical field without using it as reviewed applicability; this TI introduces the new carburetor at the following number. Later sheet K also carries a TI7/1998 model-specific replacement lead; that later review remains in the queue, not promoted here.
- Historical TI26/1996 guidance for TS 510 and TS 760 only. Source type 4205 is bound to exact named-model sheets consolidated under 4201, not a general series equivalence. TS 460 is a design comparison, not added fitment. Factory availability is historical, not a current stock guarantee. No hardware operation was performed.
Source: TI 26/1996, p. 1 · TI 26/1996, p. 3 · TI 26/1996, p. 4 · TI 26/1996, p. 5 — TS 510 / TS 760: HS 277 A replaces HS 212 B in production.
Part numbers (2)
- 4205 120 0600 — Carburetor HS 212 BOriginal; older-machine spare · TS 510 / TS 760; TS 510 / TS 760: HS 277 A replaces HS 212 B in production
- 4205 120 0601 — Carburetor HS 277 ANew production version · TS 510 / TS 760; TS 510 / TS 760: HS 277 A replaces HS 212 B in production
Historical fitment · TS 510 / TS 760
TS 510 / TS 760 HS 277 A: screws, seals and cover
Adjustment components change; one unchanged spring number doubles in quantity.
- Page 5 table items 1–9, introduced at X 24 097 471: filter 1110 121 7810 → 4221 121 7800; end cover 1110 121 0811 → 4205 121 0800; idle screw 1110 122 6201 → 4221 122 6200; added ball 4221 122 4200; low-speed screw 1110 122 6800 → 4205 122 6800; high-speed screw 1111 122 6700 → 4205 122 6700.
- Item 7 spring 1110 122 3030 has the SAME original/new number but quantity changes FROM ONE TO TWO (remark 2). Item 8 spring 1106 122 3000 is deleted in the new column but remains an older-machine spare. Added item 9 sealing ring is 4223 122 3600; drawing 328TI012 shows one at each H/L adjusting screw.
- Remark 1 retains original filter, cover, idle screw, L screw, H screw and item 8 spring for older machines. New ball 4221 122 4200 is not the removed ball 1110 122 4200 (item 11). The housing-table idle-screw change and carburetor-table idle-screw change describe the relocated function, not two independent new idle screws.
- Later HS-212B sheet L lists end cover 1111 121 0803 and filter 4221 121 7800, differing from the original column here. Those later entries do not erase the printed 1996 old numbers or establish the chronology of intermediate changes.
- Historical TI26/1996 guidance for TS 510 and TS 760 only. Source type 4205 is bound to exact named-model sheets consolidated under 4201, not a general series equivalence. TS 460 is a design comparison, not added fitment. Factory availability is historical, not a current stock guarantee. No hardware operation was performed.
Source: TI 26/1996, p. 1 · TI 26/1996, p. 3 · TI 26/1996, p. 4 · TI 26/1996, p. 5 — TS 510 / TS 760 HS 277 A: screws, seals and cover.
Part numbers (14)
- 1110 121 7810 — Carburetor filterOriginal; older-machine spare · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 4221 121 7800 — Carburetor filterNew · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 1110 121 0811 — End coverOriginal 1996 table · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 4205 121 0800 — End coverNew · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 1110 122 6201 — Idle adjusting screwOriginal · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 4221 122 6200 — Idle adjusting screwNew carburetor-body version · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 4221 122 4200 — BallNew item 4 · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 1110 122 6800 — Low-speed screwOriginal · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 4205 122 6800 — Low-speed screwNew · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 1111 122 6700 — High-speed screwOriginal · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 4205 122 6700 — High-speed screwNew · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 1110 122 3030 — Adjusting screw springSame number; quantity 1 to 2 · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 1106 122 3000 — Adjusting screw springOld version only · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 4223 122 3600 — H/L sealing ringNew item 9 · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
Historical fitment · TS 510 / TS 760
TS 510 / TS 760 HS 277 A: shaft hardware and control valve
All shaft-table rows retain their own old-spare and quantity rules.
- Page 5 items 10–24, from X 24 097 471: choke shaft with lever 1111 120 7200 → 4205 120 7200. Deleted old-column parts remain older-machine spares under remark 1: ball 1110 122 4200 (11), spring 1108 122 3001 (12), round-head screw 1106 122 7400 (13), clip 1110 122 9300 (15). Deletion here is not a prohibition on that number anywhere else in the carburetor or machine.
- Item 14 round-head screw 1110 122 7400 is UNCHANGED IN NUMBER; quantity changes FROM ONE TO TWO (remark 2). Original scan resolves scrambled text alignment: row 15 is OLD CLIP 1110 122 9300, while row 16 is NEW SEALING RING 4221 122 3605, quantity TWO. Do not turn the old clip number into a new sealing ring.
- Added row 17 ring 4221 121 9400 (2x), row 18 circlip 1110 122 9005 (2x) and row 19 torsion spring 4205 122 3200 accompany the revised shaft arrangement. Drawing 328TI012 shows the repeated ring/seal/circlip stacks; these seals differ from H/L sealing ring 4223 122 3600.
- Throttle shaft with lever 1111 120 7100 → 4221 120 7100 (20); torsion spring 1110 122 3200 → 4221 122 3200 (21); added bushing 4221 122 9100 (22, 2x); added washer 4221 121 8600 (23); control valve 4205 120 8700 → 4205 120 8705 (24). Old throttle shaft, spring and valve remain older-machine spares. The control valve is changed, NOT deleted merely because ignition now governs speed.
- Page 5 says unlisted parts are identical in the two carburetors. It does not authorize mixing the listed old and new shafts, rings, seals, springs or valves, nor give a conversion kit.
- Historical TI26/1996 guidance for TS 510 and TS 760 only. Source type 4205 is bound to exact named-model sheets consolidated under 4201, not a general series equivalence. TS 460 is a design comparison, not added fitment. Factory availability is historical, not a current stock guarantee. No hardware operation was performed.
Source: TI 26/1996, p. 1 · TI 26/1996, p. 4 · TI 26/1996, p. 5 — TS 510 / TS 760 HS 277 A: shaft hardware and control valve.
Part numbers (19)
- 1111 120 7200 — Choke shaft with leverOriginal · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 4205 120 7200 — Choke shaft with leverNew · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 1110 122 4200 — BallRemoved item 11; old spare · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 1108 122 3001 — SpringRemoved internal item 12; old spare · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 1106 122 7400 — Round-head screwRemoved item 13; old spare · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 1110 122 7400 — Round-head screwSame number; quantity 1 to 2 · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 1110 122 9300 — ClipRemoved item 15; old spare · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 4221 122 3605 — Shaft sealing ringNew item 16; quantity 2 · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 4221 121 9400 — RingNew item 17; quantity 2 · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 1110 122 9005 — CirclipNew item 18; quantity 2 · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 4205 122 3200 — Choke torsion springNew item 19 · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 1111 120 7100 — Throttle shaft with leverOriginal · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 4221 120 7100 — Throttle shaft with leverNew · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 1110 122 3200 — Throttle torsion springOriginal · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 4221 122 3200 — Throttle torsion springNew · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 4221 122 9100 — BushingNew; quantity 2 · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 4221 121 8600 — WasherNew · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 4205 120 8700 — Control valveOriginal; old spare · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 4205 120 8705 — Control valveNew; retained function · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
Service note · TS 510 / TS 760
TS 510 / TS 760 HS 277 A: standard H/L setting
H and L each open one turn; exact operating instructions for altitude correction remain a source gap.
- Section 2.1 first says that from X 24 073 218 speed is limited by the ignition system rather than the carburetor control valve; it cites TI33/1995. That earlier change is separately reviewed in the electronic-governor note. It is not the X 24 097 471 filter/carburetor change.
- Under section 2, Carburetor HS 277 A: carefully turn H and L clockwise as far as possible, then open H ONE TURN and L ONE TURN. This is the stated standard setting, not a universal setting for HS 212 B or later HS 280/281 variants, and not a complete live-engine adjustment procedure.
- The bulletin says maximum speed cannot be increased beyond the maximum design value by carburetor adjustment with the ignition limiter. That does not prove any mixture adjustment is safe, establish a numeric rpm here, or remove the need for the correct operating instructions.
- High-altitude or sea-level use MAY require a slight correction, which MUST follow the operating instructions. Source gap: the exact HS 277 A operating-instructions edition has not been identified in the available local collection. The related TS 510/760 workshop manual does not establish that exact carburetor/edition applicability and is not substituted. No correction direction, turn amount or complete live adjustment procedure is supplied here.
- Historical TI26/1996 guidance for TS 510 and TS 760 only. Source type 4205 is bound to exact named-model sheets consolidated under 4201, not a general series equivalence. TS 460 is a design comparison, not added fitment. Factory availability is historical, not a current stock guarantee. No hardware operation was performed.
Source: TI 26/1996, p. 1 · TI 26/1996, p. 4 — TS 510 / TS 760 HS 277 A: standard H/L setting.
Part numbers (1)
- 4205 120 0601 — Carburetor HS 277 AStandard-setting scope · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: standard H/L setting
Service note · TS 510 / TS 760
TS 510 / TS 760: defective vent hose and final connections
Retain the 240 / 40 / 20 mm routing stages and the distinct compensator connection.
- Section 3.2.2 applies ONLY to the NEW tank-vent system. Remove air filter, filter housing and carburetor; pry the cap off the compensating-tank twist lock and unscrew the lock. Separate the defective hose in the carburetor chamber and withdraw it through the compensating-tank opening using needle-nose pliers; remove the housing grommet.
- Drawing 328TI006: feed an approximately 50 cm (19.5 in.) trimmer line, maximum diameter 0.095 in., or flexible wire such as throttle cable, from the carburetor chamber through the compensating tank as an assembly aid. Cut one end of vent hose 4205 141 8601 obliquely; use the aid to push the other end through the tank until it protrudes. Remove the aid and push the vent insert into that protruding end. The line is an assembly aid, not a permanent vent component.
- Push on grommet (2), wet slightly with oil and press in; withdraw the hose until it projects approximately 240 mm (9.5 in.) into the carburetor chamber. Push on insulating tube 4205 141 8602 (3), leaving approximately 40 mm (1.5 in.) of hose beyond its end (328TI007). These projections are not cut lengths; the table specifies a 325 mm hose and a 200 mm tube.
- Refit carburetor and fuel hose and connect impulse hose. Press grommet (4) into the filter housing; lead the vent hose with insulating tube along the illustrated route and through the grommet (328TI008). Connect short-circuit wire (5) to the stop switch. Do not confuse the impulse hose, vent hose or short-circuit wire.
- Page 8 / 328TI009 finishes the procedure: fit the filter housing with the vent hose BEHIND THE STRAP, then pull it upward to protrude approximately 20 mm (3/4 in.). IMPORTANT: the separate COMPENSATOR hose (6) protruding DOWNWARDS from the filter housing must be firmly seated on the carburetor connection piece. The upward vent outlet is not that compensator connection. Illustration numbers 1–6 and table positions 1–10 are separate numbering systems.
- All three metric/inch pairs are the source’s approximate routing dimensions, not exact unit conversions or three successive cuts. Read the original diagrams before physical work; no live adjustment, leak test or completed repair is claimed.
- Historical TI26/1996 section 3 guidance for TS 510 and TS 760 only. Exact named-model sheets are consolidated under 4201; this is not general series interchange. Source availability statements describe 1996 supply, not current stock. No hardware operation was performed.
Source: TI 26/1996, p. 1 · TI 26/1996, p. 7 · TI 26/1996, p. 8 — TS 510 / TS 760: defective vent hose and final connections.
Part numbers (4)
- 4205 141 8601 — Vent hoseDefective-hose replacement · TS 510 / TS 760; TS 510 / TS 760: defective vent hose and final connections
- 4205 141 8602 — Insulating tube40 mm vent-hose projection · TS 510 / TS 760; TS 510 / TS 760: defective vent hose and final connections
- 4205 647 9100 — GrommetCasing and filter-housing routing · TS 510 / TS 760; TS 510 / TS 760: defective vent hose and final connections
- 4205 350 5800 — Vent insertInserted after withdrawing assembly aid · TS 510 / TS 760; TS 510 / TS 760: defective vent hose and final connections
Wrong number or missing part for the TS 510, TS 760? Report a correction →