Stihl 4201 · Section L · 11 of 24 · 32 parts
Carburetor HS-212B
Fits TS 510, TS 760.
Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.
Applies from serial 24 097 470 — check the number stamped on your machine. Change documented in Technical Information 26/1996 — Air filter system and compensator; HS 277 carburet .
Parts (32)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1110 122 9410 | Plug | 1 |
| 2 | 1110 122 3020 | Spring | 1 |
| 3 | 1110 121 5100 | Inlet needle | 1 |
| 4 | 1124 121 5000 | Inlet control lever | 1 |
| 5 | 1110 121 9200 | Spindle | 1 |
| 6 | 1110 122 7801 | Oval head screw | 1 |
| 7 | 1111 121 5400 | Valve jet | 1 |
| 8 | 1110 129 0900 | Gasket | 1 |
| 9 | 1110 121 4700 | Metering diaphragm | 1 |
| 10 | 1111 121 0803 | End cover | 1 |
| 11 | 1106 122 7400 | Round head screw Fitment / change note → | 6 |
| 12 | 1106 122 3000 | Spring Fitment / change note → | 1 |
| 13 | 1111 122 6700 | High speed adjustment screw Fitment / change note → | 1 |
| 14 | 1110 122 3030 | Spring Fitment / change note → | 1 |
| 15 | 1110 122 6800 | Low speed adjustment screw Fitment / change note → | 1 |
| 16 | 1111 120 7200 | Choke shaft with lever Fitment / change note → | 1 |
| 17 | 1110 122 3200 | Torsion spring Fitment / change note → | 1 |
| 18 | 1111 120 7100 | Throttle shaft with lever Fitment / change note → | 1 |
| 19 | 1115 121 3300 | Throttle shutter | 1 |
| 20 | 4221 121 7800 | Strainer Fitment / change note → | 1 |
| 21 | 1110 121 4800 | Pump diaphragm | 1 |
| 22 | 1110 129 1110 | Gasket | 1 |
| 23 | 1110 121 0815 | End cover | 1 |
| 24 | 1110 122 7700 | Oval head screw | 4 |
| 25 | 1110 122 9300 | Clip Fitment / change note → | 1 |
| 26 | 1110 122 7400 | Round head screw Fitment / change note → | 1 |
| 27 | 1110 129 3000 | Sealing ring | 1 |
| 28 | 4205 120 8700 | Control valve Fitment / change note → | 1 |
| 29 | 1108 122 3001 | Spring Fitment / change note → | 1 |
| 30 | 1110 122 4200 | Ball Fitment / change note → | 1 |
| 31 | 1115 121 2900 | Choke shutter | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4205 120 0600 | Carburetor HS-212B Fitment / change note → | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · TS 510 / TS 760
TS 510 / TS 760: compensator hose and choke changes
Clean-side filter pressure reaches the metering diaphragm through a shaped hose.
- Section 1: shaped hose 4205 122 4000 connects the CLEAN SIDE of the air filter to the OUTSIDE of the carburetor metering diaphragm. This compensator connection is distinct from the tank-vent hose introduced in section 3; do not join them by an assumed common purpose.
- The source describes keeping the proportion of fuel constant as the filter becomes dirty, delaying power reduction. It does not claim unchanged power indefinitely or eliminate filter maintenance. System introduction is X 24 097 471.
- Table items 18–20: choke lever 1111 185 2000 → 1111 185 2001; spring 0000 997 0326 → 1108 122 3001; hose 4205 122 4000 is added. The old choke lever is supplied only UNTIL STOCKS ARE EXHAUSTED (remark 3); the old spring remains an older-machine spare (remark 1). Do not apply one availability policy to both.
- The external choke lever and its spring are not the same table positions as the carburetor choke shaft, torsion spring or removed internal detent spring. Follow drawing 328TI011 and the separate carburetor table.
- Historical TI26/1996 guidance for TS 510 and TS 760 only. Source type 4205 is bound to exact named-model sheets consolidated under 4201, not a general series equivalence. TS 460 is a design comparison, not added fitment. Factory availability is historical, not a current stock guarantee. No hardware operation was performed.
Source: TI 26/1996, p. 1 · TI 26/1996, p. 2 · TI 26/1996, p. 3 — TS 510 / TS 760: compensator hose and choke changes.
Part numbers (5)
- 1111 185 2000 — Choke leverOriginal; stock exhaustion · TS 510 / TS 760; TS 510 / TS 760: compensator hose and choke changes
- 1111 185 2001 — Choke leverNew · TS 510 / TS 760; TS 510 / TS 760: compensator hose and choke changes
- 0000 997 0326 — Choke lever springOriginal; older-machine spare · TS 510 / TS 760; TS 510 / TS 760: compensator hose and choke changes
- 1108 122 3001 — Choke lever springNew in filter-system table · TS 510 / TS 760; TS 510 / TS 760: compensator hose and choke changes
- 4205 122 4000 — Shaped compensator hoseNew; clean-side pressure connection · TS 510 / TS 760; TS 510 / TS 760: compensator hose and choke changes
Historical fitment · TS 510 / TS 760
TS 510 / TS 760: HS 277 A replaces HS 212 B in production
The carburetor and filter change share X 24 097 471, not the earlier ignition cutoff.
- Section 2: original 4205 120 0600 (HS 212 B) is replaced by 4205 120 0601 (HS 277 A) with introduction of the new filter system from X 24 097 471. The original complete carburetor remains available for older machines under remark 1. This is a production replacement statement, not blanket standalone retrofit permission.
- The HS 277 A has a compensator connection, O-ring-sealed H/L adjusting screws with standardized springs and an idle speed screw in the carburetor body. Choke shaft, throttle shaft, control valve and listed components also change. Page 5 says ALL OTHER PARTS ARE IDENTICAL IN BOTH CARBURETORS; that does not make the explicitly changed components interchangeable.
- Page 4 separately dates ignition speed limiting to X 24 073 218 (TI33/1995). Do not move that earlier ignition event to X 24 097 471 or treat every electronically governed machine as HS 277 A-equipped.
- Later HS-212B sheet L has parsed from_serial 24097470, which conflicts with reading it as the start of the old carburetor. Preserve the canonical field without using it as reviewed applicability; this TI introduces the new carburetor at the following number. Later sheet K also carries a TI7/1998 model-specific replacement lead; that later review remains in the queue, not promoted here.
- Historical TI26/1996 guidance for TS 510 and TS 760 only. Source type 4205 is bound to exact named-model sheets consolidated under 4201, not a general series equivalence. TS 460 is a design comparison, not added fitment. Factory availability is historical, not a current stock guarantee. No hardware operation was performed.
Source: TI 26/1996, p. 1 · TI 26/1996, p. 3 · TI 26/1996, p. 4 · TI 26/1996, p. 5 — TS 510 / TS 760: HS 277 A replaces HS 212 B in production.
Part numbers (2)
- 4205 120 0600 — Carburetor HS 212 BOriginal; older-machine spare · TS 510 / TS 760; TS 510 / TS 760: HS 277 A replaces HS 212 B in production
- 4205 120 0601 — Carburetor HS 277 ANew production version · TS 510 / TS 760; TS 510 / TS 760: HS 277 A replaces HS 212 B in production
Historical fitment · TS 510 / TS 760
TS 510 / TS 760 HS 277 A: screws, seals and cover
Adjustment components change; one unchanged spring number doubles in quantity.
- Page 5 table items 1–9, introduced at X 24 097 471: filter 1110 121 7810 → 4221 121 7800; end cover 1110 121 0811 → 4205 121 0800; idle screw 1110 122 6201 → 4221 122 6200; added ball 4221 122 4200; low-speed screw 1110 122 6800 → 4205 122 6800; high-speed screw 1111 122 6700 → 4205 122 6700.
- Item 7 spring 1110 122 3030 has the SAME original/new number but quantity changes FROM ONE TO TWO (remark 2). Item 8 spring 1106 122 3000 is deleted in the new column but remains an older-machine spare. Added item 9 sealing ring is 4223 122 3600; drawing 328TI012 shows one at each H/L adjusting screw.
- Remark 1 retains original filter, cover, idle screw, L screw, H screw and item 8 spring for older machines. New ball 4221 122 4200 is not the removed ball 1110 122 4200 (item 11). The housing-table idle-screw change and carburetor-table idle-screw change describe the relocated function, not two independent new idle screws.
- Later HS-212B sheet L lists end cover 1111 121 0803 and filter 4221 121 7800, differing from the original column here. Those later entries do not erase the printed 1996 old numbers or establish the chronology of intermediate changes.
- Historical TI26/1996 guidance for TS 510 and TS 760 only. Source type 4205 is bound to exact named-model sheets consolidated under 4201, not a general series equivalence. TS 460 is a design comparison, not added fitment. Factory availability is historical, not a current stock guarantee. No hardware operation was performed.
Source: TI 26/1996, p. 1 · TI 26/1996, p. 3 · TI 26/1996, p. 4 · TI 26/1996, p. 5 — TS 510 / TS 760 HS 277 A: screws, seals and cover.
Part numbers (14)
- 1110 121 7810 — Carburetor filterOriginal; older-machine spare · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 4221 121 7800 — Carburetor filterNew · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 1110 121 0811 — End coverOriginal 1996 table · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 4205 121 0800 — End coverNew · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 1110 122 6201 — Idle adjusting screwOriginal · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 4221 122 6200 — Idle adjusting screwNew carburetor-body version · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 4221 122 4200 — BallNew item 4 · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 1110 122 6800 — Low-speed screwOriginal · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 4205 122 6800 — Low-speed screwNew · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 1111 122 6700 — High-speed screwOriginal · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 4205 122 6700 — High-speed screwNew · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 1110 122 3030 — Adjusting screw springSame number; quantity 1 to 2 · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 1106 122 3000 — Adjusting screw springOld version only · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
- 4223 122 3600 — H/L sealing ringNew item 9 · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: screws, seals and cover
Historical fitment · TS 510 / TS 760
TS 510 / TS 760 HS 277 A: shaft hardware and control valve
All shaft-table rows retain their own old-spare and quantity rules.
- Page 5 items 10–24, from X 24 097 471: choke shaft with lever 1111 120 7200 → 4205 120 7200. Deleted old-column parts remain older-machine spares under remark 1: ball 1110 122 4200 (11), spring 1108 122 3001 (12), round-head screw 1106 122 7400 (13), clip 1110 122 9300 (15). Deletion here is not a prohibition on that number anywhere else in the carburetor or machine.
- Item 14 round-head screw 1110 122 7400 is UNCHANGED IN NUMBER; quantity changes FROM ONE TO TWO (remark 2). Original scan resolves scrambled text alignment: row 15 is OLD CLIP 1110 122 9300, while row 16 is NEW SEALING RING 4221 122 3605, quantity TWO. Do not turn the old clip number into a new sealing ring.
- Added row 17 ring 4221 121 9400 (2x), row 18 circlip 1110 122 9005 (2x) and row 19 torsion spring 4205 122 3200 accompany the revised shaft arrangement. Drawing 328TI012 shows the repeated ring/seal/circlip stacks; these seals differ from H/L sealing ring 4223 122 3600.
- Throttle shaft with lever 1111 120 7100 → 4221 120 7100 (20); torsion spring 1110 122 3200 → 4221 122 3200 (21); added bushing 4221 122 9100 (22, 2x); added washer 4221 121 8600 (23); control valve 4205 120 8700 → 4205 120 8705 (24). Old throttle shaft, spring and valve remain older-machine spares. The control valve is changed, NOT deleted merely because ignition now governs speed.
- Page 5 says unlisted parts are identical in the two carburetors. It does not authorize mixing the listed old and new shafts, rings, seals, springs or valves, nor give a conversion kit.
- Historical TI26/1996 guidance for TS 510 and TS 760 only. Source type 4205 is bound to exact named-model sheets consolidated under 4201, not a general series equivalence. TS 460 is a design comparison, not added fitment. Factory availability is historical, not a current stock guarantee. No hardware operation was performed.
Source: TI 26/1996, p. 1 · TI 26/1996, p. 4 · TI 26/1996, p. 5 — TS 510 / TS 760 HS 277 A: shaft hardware and control valve.
Part numbers (19)
- 1111 120 7200 — Choke shaft with leverOriginal · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 4205 120 7200 — Choke shaft with leverNew · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 1110 122 4200 — BallRemoved item 11; old spare · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 1108 122 3001 — SpringRemoved internal item 12; old spare · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 1106 122 7400 — Round-head screwRemoved item 13; old spare · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 1110 122 7400 — Round-head screwSame number; quantity 1 to 2 · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 1110 122 9300 — ClipRemoved item 15; old spare · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 4221 122 3605 — Shaft sealing ringNew item 16; quantity 2 · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 4221 121 9400 — RingNew item 17; quantity 2 · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 1110 122 9005 — CirclipNew item 18; quantity 2 · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 4205 122 3200 — Choke torsion springNew item 19 · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 1111 120 7100 — Throttle shaft with leverOriginal · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 4221 120 7100 — Throttle shaft with leverNew · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 1110 122 3200 — Throttle torsion springOriginal · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 4221 122 3200 — Throttle torsion springNew · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 4221 122 9100 — BushingNew; quantity 2 · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 4221 121 8600 — WasherNew · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 4205 120 8700 — Control valveOriginal; old spare · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
- 4205 120 8705 — Control valveNew; retained function · TS 510 / TS 760; TS 510 / TS 760 HS 277 A: shaft hardware and control valve
Wrong number or missing part for the TS 510, TS 760? Report a correction →