Stihl 4201 · Section M · 12 of 24 · 40 parts
Carburetor HS-280D, HS-281D
Fits TS 510, TS 760.
Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.
Parts (40)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4221 121 7800 | Strainer | 1 |
| 2 | 1110 121 4800 | Pump diaphragm | 1 |
| 3 | 1110 129 1110 | Gasket | 1 |
| 4 | 1110 121 0815 | End cover | 1 |
| 5 | 1110 122 7700 | Oval head screw | 4 |
| 6 | 1110 122 3020 | Spring | 1 |
| 7 | 4116 121 5100 | Inlet needle Fitment / change note → | 1 |
| 8 | 1124 121 5000 | Inlet control lever Fitment / change note → | 1 |
| 9 | 1110 121 9200 | Spindle | 1 |
| 10 | 1110 122 7801 | Oval head screw | 1 |
| 11 | 4221 121 5400 | Valve jet Fitment / change note → | 1 |
| 12 | 4205 121 5601 | Fixed jet 0.61 | 1 |
| 13 | 1110 122 9410 | Plug | 1 |
| 14 | 1110 129 0900 | Gasket | 1 |
| 15 | 1110 121 4700 | Metering diaphragm | 1 |
| 16 | 4205 121 0800 | End cover | 1 |
| 17 | 1106 122 7400 | Round head screw | 4 |
| 18 | 1115 121 2900 | Choke shutter | 1 |
| 19 | 1110 122 7400 | Round head screw | 2 |
| 20 | 1115 121 3300 | Throttle shutter | 1 |
| 22 | 4205 122 3000 | Spring Fitment / change note → | 2 |
| 23 | 4205 122 6701 | High speed adjustment screw Fitment / change note → | 1 |
| 24 | 4205 121 2700 | Cap | 2 |
| 25 | 4205 122 6801 | Low speed adjustment screw Fitment / change note → | 1 |
| 26 | 4221 122 4200 | Ball | 1 |
| 27 | 4221 122 6200 | Idle speed adjustment screw | 1 |
| 28 | 4221 122 3605 | Sealing ring | 2 |
| 29 | 4221 121 9400 | Ring | 2 |
| 30 | 4205 122 3200 | Torsion spring | 1 |
| 31 | 4205 120 7200 | Choke shaft with lever | 1 |
| 33 | 1110 129 3000 | Sealing ring | 1 |
| 34 | 4205 120 8701 | Control valve Fitment / change note → | 1 |
| 35 | 4221 121 8600 | Washer | 1 |
| 36 | 4221 122 9100 | Bushing | 2 |
| 37 | 4221 122 3200 | Torsion spring | 1 |
| 38 | 4221 120 7101 | Throttle shaft with lever Fitment / change note → | 1 |
| 39 | 5910 890 4500 | Puller Fitment / change note → option | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4205 120 0602 | Carburetor HS-280D Fitment / change note → | 1 |
| — | 4205 120 0603 | Carburetor HS-281D Fitment / change note → | 1 |
| — | 1115 007 1060 | Set of carburetor parts | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · TS 510 / TS 760
TS 510 / TS 760: HS280A and HS281A have different model assignments
The shared HS277A original branches to model-specific EPA replacements.
- Historical TI07/1998 for TS 510 and TS 760, type 4205. The exact-model 2012 IPL is filed under catalog family 4201; that navigation key does not change the TI type. Later sheets are comparison/navigation evidence, not proof that later carburetor revisions share the 1998 settings. Historical factory availability is not current stock or verified physical interchange. No hardware operation was performed.
- Original HS277A 4205 120 0601 is replaced by HS280A 4205 120 0602 for TS 510 EPA and by HS281A 4205 120 0603 for TS 760 EPA. These are TWO model-conditioned replacements, not one universal successor and not authorization to exchange the TS510 and TS760 carburetors.
- The new carburetors limit BOTH high-speed and low-speed screw adjustment. Each assembly includes the corresponding listed component versions; OTHER PARTS AS BEFORE. The puller is a separate special-tool row, not an installed carburetor component.
- Introduction is CONTINUOUS, with no numeric serial cutoff. Remark1 applies to the original complete HS277A: it REMAINS AVAILABLE for machines WITHOUT EPA PERMIT. Do not convert this into withdrawal of the original or unrestricted EPA/non-EPA interchange.
- The later exact-model IPL names the same 0602 and 0603 numbers HS280D and HS281D, respectively. TI07 names them HS280A and HS281A. Preserve the revision-name difference; number identity does not prove identical internal parts or settings.
- The TI factory claims optimum mixture, smooth running, fuel efficiency, reliability and low emissions. Those are vendor statements, not measured results from this review.
Source: TI 7/1998, p. 1 · TI 7/1998, p. 4 — Section 1 replacement and section 1.6 assembly rows/remark.
Part numbers (3)
- 4205 120 0601 — Carburetor HS277AOriginal; retained for non-EPA machines · TS 510 and TS 760; only the stated version and restrictions
- 4205 120 0602 — Carburetor HS280A in TI07New EPA version · TS 510; only the stated version and restrictions
- 4205 120 0603 — Carburetor HS281A in TI07New EPA version · TS 760; only the stated version and restrictions
Conditional replacement · TS 510 / TS 760
TS 510 / TS 760: nine component rows retain the historical jet and cap
Later HS280D/HS281D jet and cap numbers do not overwrite the A-version table.
- Historical TI07/1998 for TS 510 and TS 760, type 4205. The exact-model 2012 IPL is filed under catalog family 4201; that navigation key does not change the TI type. Later sheets are comparison/navigation evidence, not proof that later carburetor revisions share the 1998 settings. Historical factory availability is not current stock or verified physical interchange. No hardware operation was performed.
- Row 1 inlet needle: 1110 121 5100 → 4116 121 5100. Row 2 inlet control lever: 1110 121 5000 → 1124 121 5000. Row 3 valve jet: 1111 121 5400 → 4221 121 5400. Row 4 ADDS fixed jet 0.64, 4205 121 5600; its original column is a dash.
- Row 5 spring: 1110 122 3030 → 4205 122 3000. Row 6 HIGH-speed screw: 4205 122 6700 → 4205 122 6701. Row 7 ADDS cap 1124 121 2700. Row 8 LOW-speed screw: 4205 122 6800 → 4205 122 6801. Row 9 throttle shaft with lever: 4221 120 7100 → 4221 120 7101. Both adjusting screws remain present despite the added fixed jet.
- Page 1 drawing 328TI020 KN uses FUNCTION callouts 1 caps,2 H screw,3 L screw and 4 module. The screws have KNURLED HEADS that lock the caps; moulded cams in the module stop the cap tabs. These callouts differ from the page 3 exploded-view/page 4 summary numbering. The exploded view shows two springs and two caps; row 10 is the puller. No separate module order number is printed.
- The later D-version IPL lists fixed jet 4205 121 5601 described as 0.61 and cap 4205 121 2700, versus TI07 fixed jet 4205 121 5600 described as 0.64 and cap 1124 121 2700. Preserve both edition differences; do not silently substitute later numbers, sizes or settings. The later HS277A sheet also lists 1124 121 5000 as its lever, whereas TI07 gives 1110 121 5000 on the ORIGINAL side.
- The summary says OTHER PARTS AS BEFORE and continuous introduction. Its non-EPA availability remark is attached to the original complete carburetor, not every individual component row; no independent component supply rule is invented.
Source: TI 7/1998, p. 1 · TI 7/1998, p. 3 · TI 7/1998, p. 4 — Section 1.1 functional diagram, exploded view and section 1.6 rows 1–9.
Part numbers (16)
- 1110 121 5100 — Inlet needleOriginal version · TS 510 and TS 760; only the stated version and restrictions
- 4116 121 5100 — Inlet needleNew A-version component · TS 510 and TS 760; only the stated version and restrictions
- 1110 121 5000 — Inlet control leverOriginal version · TS 510 and TS 760; only the stated version and restrictions
- 1124 121 5000 — Inlet control leverNew A-version component · TS 510 and TS 760; only the stated version and restrictions
- 1111 121 5400 — Valve jetOriginal version · TS 510 and TS 760; only the stated version and restrictions
- 4221 121 5400 — Valve jetNew A-version component · TS 510 and TS 760; only the stated version and restrictions
- 4205 121 5600 — Fixed jet 0.64New A-version component · TS 510 and TS 760; only the stated version and restrictions
- 1110 122 3030 — SpringOriginal version · TS 510 and TS 760; only the stated version and restrictions
- 4205 122 3000 — SpringNew A-version component · TS 510 and TS 760; only the stated version and restrictions
- 4205 122 6700 — High-speed adjusting screwOriginal version · TS 510 and TS 760; only the stated version and restrictions
- 4205 122 6701 — High-speed adjusting screwNew A-version component · TS 510 and TS 760; only the stated version and restrictions
- 1124 121 2700 — CapNew A-version component · TS 510 and TS 760; only the stated version and restrictions
- 4205 122 6800 — Low-speed adjusting screwOriginal version · TS 510 and TS 760; only the stated version and restrictions
- 4205 122 6801 — Low-speed adjusting screwNew A-version component · TS 510 and TS 760; only the stated version and restrictions
- 4221 120 7100 — Throttle shaft with leverOriginal version · TS 510 and TS 760; only the stated version and restrictions
- 4221 120 7101 — Throttle shaft with leverNew A-version component · TS 510 and TS 760; only the stated version and restrictions
Service note · TS 510 / TS 760
TS 510 / TS 760: capped H half-turn and L quarter-turn start at lean
Both screws have 180-degree travel; altitude correction retains the overheating warning.
- Historical TI07/1998 for TS 510 and TS 760, type 4205. The exact-model 2012 IPL is filed under catalog family 4201; that navigation key does not change the TI type. Later sheets are comparison/navigation evidence, not proof that later carburetor revisions share the 1998 settings. Historical factory availability is not current stock or verified physical interchange. No hardware operation was performed.
- For HS280A/HS281A with caps fitted, H = ONE-HALF TURN OPEN and L = ONE-QUARTER TURN OPEN, each measured from the LEAN SETTING, not from the screw seat. Drawing 328TI021 KN identifies H,L and the separate idle screwLA.
- The text says adjustment can be corrected by up to 180°; drawing 328TI022 KN shows180° travel for BOTH H and L. Do not import a90° H limit from a different carburetor bulletin.
- For unsatisfactory running at HIGHER ALTITUDES: CHECK STANDARD SETTING, WARM UP the engine, then turn HIGH-speed screwH CLOCKWISE (leaner). Only slight readjustment may be necessary. The warning states that an excessively lean setting can damage the engine through INSUFFICIENT LUBRICATION AND OVERHEATING. No altitude table, H target speed or extra uncapped adjustment is supplied.
- The generic Owner’s Manual Carburetor adjustment chapter is cited as the same standard setting; the TI itself reproduces that setting. No exact manual edition is established or silently used.
Source: TI 7/1998, p. 2 — Section 1.2 complete standard-setting and altitude instructions.
No additional parts-table entry added.
Service note · TS 510 / TS 760
TS 510 / TS 760: new caps follow one-turn uncapped H/L basic settings
Counterclockwise puller, single-use caps and 1,800 rpm idle remain explicit.
- Historical TI07/1998 for TS 510 and TS 760, type 4205. The exact-model 2012 IPL is filed under catalog family 4201; that navigation key does not change the TI type. Later sheets are comparison/navigation evidence, not proof that later carburetor revisions share the 1998 settings. Historical factory availability is not current stock or verified physical interchange. No hardware operation was performed.
- To replace the adjusting screws or clean the carburetor, REMOVE the caps using puller 5910 890 4500. Screw the puller into each cap COUNTERCLOCKWISE until the cap comes off. The caps are DAMAGED by removal and MUST NOT BE REUSED. Unlike some other carburetor designs, no separate locating-ring replacement is stated here.
- After refitting the screws, make the BASIC SETTING WITHOUT CAPS: the source says “With the adjusting screws hard against their seats”, then H = BACK OFF ONE TURN and L = BACK OFF ONE TURN. Preserve that historical wording; no seating torque is supplied. These seat-based values are distinct from the capped H half-turn/L quarter-turn values measured from lean.
- Fit NEW caps with tabs positioned as in drawing 328TI024 KN: the H tab points LEFT and the L tab points DOWN in the illustrated front view. Press caps onto the screws until FLUSH WITH THE MODULE EDGE. The TI says the resulting cap AND screw positions correspond exactly to the standard setting; it does not instruct changing the screw position during cap installation.
- Set IDLE speed to 1,800 rpm using LA; USE A TACHOMETER. This is idle speed, not maximum engine speed or either model’s power rating. All settings here are for the historical HS280A/HS281A versions.
- Page 4 row 10 identifies5910 890 4500 as a SPECIAL TOOL separate from the assembly inclusion rows. The cap order number in this TI is 1124 121 2700; later D-version cap differences remain in the component note.
Source: TI 7/1998, p. 2 · TI 7/1998, p. 3 · TI 7/1998, p. 4 — Sections1.3–1.3.2, cap installation drawing and summary tool row 10.
Part numbers (2)
- 5910 890 4500 — PullerSpecial tool; counterclockwise cap removal · TS 510 and TS 760; only the stated version and restrictions
- 1124 121 2700 — CapNew single-use replacement in TI07 · TS 510 and TS 760; only the stated version and restrictions
Service note · TS 510 / TS 760
TS 510 / TS 760: 50:1 fuel and EPA label retain the missing TI27 dependency
Delegated fuel/emission-system details are a bounded source gap.
- Historical TI07/1998 for TS 510 and TS 760, type 4205. The exact-model 2012 IPL is filed under catalog family 4201; that navigation key does not change the TI type. Later sheets are comparison/navigation evidence, not proof that later carburetor revisions share the 1998 settings. Historical factory availability is not current stock or verified physical interchange. No hardware operation was performed.
- The factory applies the pictured U.S. EPA Phase1 label to machines conforming to the stated standard. Drawing 000TI013 KN is a TEMPLATE with engine-family/type/displacement/manufacture-date blanks, not identified machine data or a complete label order number. Its generic Owner’s Manual reference does not establish an edition.
- The EPA permit was obtained with a fuel-oil mixture of 50:1. Further fuel details and Federal Emission Control Systems Utility Engines explicitly refer to TI27/1997. That source is absent from the retained 690TIs and the bounded current 766-PDF filename inventory reverified here; delegated details remain a SOURCE GAP, not invented warranty terms, legal permission or measured compliance.
- The cover says the described changes achieve EPA compliance. Retain this as a historical vendor claim for the described configuration, not present-day certification of an owner’s machine. The TI reproduces its own standard/basic setting and idle guidance, so those locally available instructions are not deferred to the missing TI27.
Source: TI 7/1998, p. 1 · TI 7/1998, p. 3 — Cover EPA statement/label and sections1.4–1.5.
No additional parts-table entry added.
Conditional replacement · TS 510 / TS 760
TS 510 / TS 760: 9,200 RPM trigger requires matching control valve
The 16-inch TS 760 is excluded from the trigger change. Printed trigger identification numbers are not spare-part order numbers.
- TI32/1999 names TS 510 and TS 760, series 4205. Exact-model navigation is under catalog family 4201 in the 2012 IPL; this does not change the source type or extend applicability to TS 350/360. Historical availability is not current stock, and source review is not verified physical interchange.
- The cut-off speed changes from 8,400 RPM to 9,200 RPM from serial 3 38 376 502 for TS 510 and 3 38 377 502 for TS 760. The special TS 760 version for 16-inch cutting wheels is not affected by this change of trigger unit. These are model-specific printed serial thresholds, not a universal date, cutting-wheel speed rating or permission to raise the speed of an arbitrary machine.
- Trigger unit order number 4205 400 1001 (8,400 RPM) is replaced by 4205 400 1000 (9,200 RPM), subject to the 16-inch exception. The page 1 top drawing shows printed identification 4205 400 1006 on the previous unit; the bottom shows 4205 400 1005 on the new unit. These printed identification numbers are not spare-part order numbers. Drawing 328TI000 KN and its captions distinguish identification from ordering; no false replacement-part rows are created for 1006 or 1005.
- Control valve 4205 120 8705, stamped 070/15, is replaced by 4205 120 8701, stamped 070/16. Drawing 328TI027 KN shows the previous valve on the left and new valve on the right. The new valve suits the higher trigger cut-off speed; limiting engine speed by enriching the mixture occurs only if the trigger unit fails. This is the described backup limiting function, not an instruction to defeat the trigger or a diagnostic proof of failure.
- The valve change renames HS 280 A to HS 280 B for TS 510 and HS 281 A to HS 281 B for TS 760. Carburetor order numbers remain 4205 120 0602 and 4205 120 0603 respectively. Summary rows 2–5 are paired old/new versions, not four different order numbers; each listed carburetor includes the corresponding control valve. The later 2012 IPL calls these numbers HS-280D / HS-281D: retain that later designation separately, not as proof that A, B and D are identical.
- If a faulty trigger 4205 400 1001 is replaced by 4205 400 1000, control valve 4205 120 8701 (070/16) must also be installed. This mandatory pairing does not erase the special 16-inch TS 760 exclusion. No reverse substitution, all-wheel conversion or independent approval of higher cutting speed is stated.
- Page 2 remark 1 retains the previous trigger for TS 760 with 16-inch cutting wheels. Remark 2 says only the modified carburetor version is available from the factory. Remark 3 permits the new control valve on older machines; that allowance belongs to the valve and is not unrestricted permission to change every trigger unit. These are 1999 availability/compatibility statements.
- Both original pages and their quiet regions were reviewed. The footer points to TI31/1997 as the last TI, not a delegated procedure. No additional manual is required by this bulletin, and no setting screw adjustment, torque, wheel compatibility approval or completed hardware test is supplied. Earlier source conflicts and dispositions remain unchanged.
Source: TI 32/1999, p. 1 · TI 32/1999, p. 2 — Section 1, both page 1 diagrams and complete page 2 summary/remarks.
Part numbers (6)
- 4205 400 1001 — Trigger unit, 8,400 RPM limitPrevious order number; retained for 16-inch TS 760 · TS 510 / TS 760; special 16-inch TS 760 excluded from trigger change
- 4205 400 1000 — Trigger unit, 9,200 RPM limitNew order number; paired valve required · TS 510 / TS 760 except special 16-inch TS 760
- 4205 120 8705 — Control valve, marking 070/15Previous control valve · HS 280 A / HS 281 A as described in TI32/1999
- 4205 120 8701 — Control valve, marking 070/16New valve; required with replacement trigger 4205 400 1000 · Stated TS 510 / TS 760 carburetors; also usable on older machines per remark 3
- 4205 120 0602 — Carburetor HS 280 A → HS 280 BOrder number unchanged across the stated A-to-B revision · TS 510
- 4205 120 0603 — Carburetor HS 281 A → HS 281 BOrder number unchanged across the stated A-to-B revision · TS 760
Wrong number or missing part for the TS 510, TS 760? Report a correction →