← Cut-off machines · series 4201

Stihl 4201 · Section N · 13 of 24 · 41 parts

Shroud, Handle frame

Fits TS 510, TS 760.

Parts diagrams →

Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151617181922021222324252626272829333331323233343536373839440556789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (41)

PosPart numberDescriptionQty
1 4205 080 1600 Shroud 1
2 1110 145 9001 Plug 2
3 9022 341 1010 Spline screw IS-M5x18 12
4 9027 068 1480 Flat head screw M6x75 1
5 1111 790 9915 Annular buffer 2
6 1111 791 7600 Support 1
7 1111 791 2700 Tube 1
8 9214 320 0900 Lock nut M6 1
9 1111 791 4902 Handle frame 1
10 1111 791 2201 Rubber grip 1
11 0000 998 1000 Torsion spring 1
12 1111 182 1002 Throttle trigger 1
13 9373 542 2610 Cylindrical pin 5x18 1
14 1114 182 8900 Pin 1
15 0000 997 0603 Compression spring 1
16 1111 182 9300 Starting throttle lock 1
17 0000 998 0802 Torsion spring 1
18 1111 182 0800 Lockout lever 1
19 9371 470 2110 Cylindrical pin 4x16 1
20 1111 790 1700 Handlebar with hose 1
21 not sold separately Handle hose 320 mm /12 5/8" 1
22 4205 791 7602 Support 1
23 4201 791 8600 Thrust washer 1
24 9007 319 1930 Hexagon head screw M8x45 1
25 1111 791 1901 Handlebar support 1
26 1111 790 9905 Annular buffer 2
27 1111 791 9800 Washer 1
28 9022 341 1090 Spline screw IS-M5x40 1
29 1111 146 6009 Guard 1
31 4205 790 9301 Rubber buffer Fitment / change note → 1
32 9037 319 1750 Socket head screw M8x12 2
33 0000 958 0503 Washer 1
34 4205 145 9000 Plug Fitment / change note → 1
35 4205 790 9300 Rubber buffer Fitment / change note → 1
36 4205 791 7601 Support 1
37 4205 791 7400 Strap 1
38 9041 216 1350 Pan head screw M6x25 2
39 0000 967 3702 Warning pictogram TS 1
40 0000 967 3502 Instruction label 1
40 0000 967 3685 Instruction label 1
Not numbered on the diagram — assemblies, kits and options
— 0000 791 2005 Handle hose Ø 23 mm x 5m / 1x197'' option 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · TS 510 / TS 760

TS 510 / TS 760: complete 400 mm attachment and belt guard

The larger pulley, reinforced support, correct belt guard and 8400 RPM limiter are joint conditions.

Later reviewed guidance: TS 760: 400 mm wheels are factory-version only

  • Section 6.1 announces future availability of 400 mm (16 in.) attachment kits and cutting wheels, not evidence that every earlier machine was equipped for them. The kit has an aluminium guard, larger V-belt pulley, reinforced bearing and 103 mm thrust washers. Fit ONLY the COMPLETE attachment kit with reinforced bearing and larger pulley, together with V-belt guard 4201 700 8116, on a TS 510/760 limited to 8400 RPM. The trigger reference conflicts (section 5:4205 400 1001; section 6.1:4201 400 1001) and remains unresolved, not a verified alternative.
  • The larger pulley is 4205 704 1004 (summary item 8). V-belt guard 4201 700 8114 is deleted as the standard version and replaced by 4201 700 8116 to accommodate that pulley diameter. The new guard and eccentric adjuster are supplied in the 400 mm kit 4205 007 1018; adjuster item 10 remains 4205 708 3201 in BOTH old and new columns. The kit inclusion range is 2,3,6,7,8,9,10, not every row in the summary.
  • The TWO front rubber vibration buffers (machine rests), item 12, change 4205 790 9300 to lengthened 4205 790 9301, increasing wheel-to-ground clearance when switching off. The prose says generally replaced; do not claim these separately listed buffers are included within the 400 mm kit’s stated item range. Old belt guard and rubber buffers remain available only until stocks are exhausted (remark 3).
  • Later sheets E and N each list the new rubber buffer at different locations, with the original also on N; these are not proof that every configuration has the 1996 pair installed. Later sheet O has the larger pulley but a different belt-guard listing 4205 706 8105 and support/guard alternatives; that does not erase the explicitly printed 1996 complete-kit restriction or prove a supersession chain.
  • Historical TI26/1996 sections 5–7, applied here to TS 510 and TS 760 only. Shared catalog sheets do not establish unrestricted interchange. Supply statements describe 1996, not current stock. No hardware operation was performed.

Source: TI 26/1996, p. 1 · TI 26/1996, p. 10 · TI 26/1996, p. 11 · TI 26/1996, p. 12 · TI 26/1996, p. 13 — TS 510 / TS 760: complete 400 mm attachment and belt guard.

Part numbers (7)
  • 4205 007 1018 — 400 mm complete attachment kitUSA; all stated conditions required · TS 510 / TS 760; TS 510 / TS 760: complete 400 mm attachment and belt guard
  • 4205 704 1004 — Larger V-belt pulley400 mm kit item 8 · TS 510 / TS 760; TS 510 / TS 760: complete 400 mm attachment and belt guard
  • 4201 700 8114 — Original V-belt guardStock exhaustion · TS 510 / TS 760; TS 510 / TS 760: complete 400 mm attachment and belt guard
  • 4201 700 8116 — New V-belt guardRequired with 400 mm kit · TS 510 / TS 760; TS 510 / TS 760: complete 400 mm attachment and belt guard
  • 4205 708 3201 — Eccentric adjusterUnchanged number; included · TS 510 / TS 760; TS 510 / TS 760: complete 400 mm attachment and belt guard
  • 4205 790 9300 — Original rubber vibration bufferTwo front rests; stock exhaustion · TS 510 / TS 760; TS 510 / TS 760: complete 400 mm attachment and belt guard
  • 4205 790 9301 — Lengthened rubber vibration bufferTwo front rests; increased ground clearance · TS 510 / TS 760; TS 510 / TS 760: complete 400 mm attachment and belt guard

Conditional replacement · TS 510 / TS 760

TS 510 / TS 760: cover and plug close different shroud openings

Model-dependent decompression-valve position leaves one unused opening.

  • Historical TI07/1998 for TS 510 and TS 760, type 4205. The exact-model 2012 IPL is filed under catalog family 4201; that navigation key does not change the TI type. Later sheets are comparison/navigation evidence, not proof that later carburetor revisions share the 1998 settings. Historical factory availability is not current stock or verified physical interchange. No hardware operation was performed.
  • Cover 4205 084 1600 (callout 1) closes the gap in the shroud around the SPARK PLUG TERMINAL. Plug 4205 145 9000 (callout 2) seals the UNUSED one of TWO openings indicated by arrows in the shroud.
  • The decompression valve is in DIFFERENT POSITIONS on TS510 and TS760, leaving one opening unused. The illustration does not assign a left/right opening to each model in text; do not invent such an assignment or plug both openings.
  • Both items have dashes on the original side and new numbers in the summary. Introduction is continuous with no serial cutoff; the cylinder availability footnote is attached to the old cylinder rows, not a separate old-cover or old-plug supply claim.
  • The later IPL places the cover on the cylinder sheet and the plug on the shroud/handle-frame sheet. Neither is a carburetor limiter cap, and the TI prints no changed shroud order number or additional installation torque.

Source: TI 7/1998, p. 4 · TI 7/1998, p. 5 — Section 2.2 drawing 328TI026 KN and cylinder-summary rows 1–2.

Part numbers (2)
  • 4205 084 1600 — Cover around spark plug terminalNew · TS 510 and TS 760; only the stated version and restrictions
  • 4205 145 9000 — Plug for unused shroud openingNew · TS 510 and TS 760; only the stated version and restrictions

Wrong number or missing part for the TS 510, TS 760? Report a correction →