Stihl 4221 · Section B · 2 of 20 · 25 parts
Fuel tank, Tank vent
Fits TS 460.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (25)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4221 350 0400 | Fuel tank | 1 |
| 2 | 4221 353 0700 | Sealing ring | 1 |
| 3 | 4221 353 9201 | Grommet → replaced by 0000 989 0516, 0000 989 0516 TI 14/1996 | 1 |
| 4 | 1124 358 7706 | Hose 155 mm / 6 1/8'' | 1 |
| 5 | 4221 353 9200 | Grommet | 1 |
| 6 | 4221 353 2500 | Elbow connector | 1 |
| 7 | 1115 358 7700 | Hose | 1 |
| 8 | 0000 350 3500 | Pickup body | 1 |
| 9 | 4221 350 0600 | Expansion tank | 1 |
| 10 | 0000 989 0516 | Grommet | 1 |
| 11 | 4223 353 9201 | Grommet | 1 |
| 12 | 4205 141 8601 | Hose 325 mm / 12 13/16'' | 1 |
| 13 | 4223 350 5803 | Tank vent | 1 |
| 14 | 4130 358 7600 | Hose | 1 |
| 15 | 4226 122 3900 | Elbow connector | 1 |
| 16 | 4221 350 1400 | Connector | 1 |
| 17 | 1120 358 8105 | Vent insert | 1 |
| 18 | 4221 020 3500 | Housing cover | 1 |
| 19 | 4221 028 1300 | Shim | 6 |
| 20 | 9022 341 0976 | Spline screw IS-M5x14 | 7 |
| 21 | 4221 350 0500 | Filler cap | 1 |
| 22 | 9645 945 7788 | O-ring 28x3 | 1 |
| 23 | 0000 350 0900 | Rope | 1 |
| 24 | 0000 353 0701 | Ring | 1 |
| 25 | 4221 028 1305 | Shim | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · TS 460
TS 460 fuel reservoir, five AV buffers and forward exhaust
0.96 litre tank; separate compensator reservoir returns fuel under negative pressure.
- The fuel tank holds 0.96 litres / 2.02 pt (960 ccm). Its large filler opening is on top of the housing; the TI describes filling in the normal working position, for example with the STIHL filling system. Ease-of-filling wording is not permission to refuel a running or hot engine.
- Tank and compensator reservoir are installed inside the engine housing. Excess tank pressure sends fuel through a connecting hose into the reservoir; negative pressure returns it to the tank. This reservoir is NOT the clean-air pressure compensator on the carburetor.
- The claim that this arrangement prevents fuel or fuel-vapour escape is the historical functional description, not an emissions certification or a leak test performed by this project. Do not backdate the separate 47/1999 tank-vent revision to this 1995 description.
- FIVE rubber buffers on the engine housing separate the handle system from the engine unit and all other assemblies attached to that housing. Vibration reduction is a vendor description, not a measured acceleration value.
- The generously sized exhaust muffler is described as reducing noise effectively, with exhaust gases emitted to the FRONT. This paragraph gives no decibel rating, spark-arrestor approval or muffler part number.
- Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.
Source: TI 43/1995, p. 5 — TS 460 fuel reservoir, five AV buffers and forward exhaust.
No additional parts-table entry added.
Conditional replacement · TS 460
TS 460 sintered-filter tank vent: two hoses replace the through-hose
X 32 144 279 verified on scan; old valve number retained.
X 32 144 279 — Introduction from this printed machine number for TS 460 and this modification only; not a model-identification range or a cutoff for other changes.
- Both the original page 5 prose and summary print X 32 144 279. Retained extracted prose drops the last digit as X 32 144 27, while its summary preserves the full serial. This is an EXTRACTION CORRECTION verified against the scan, not a printed-source conflict or two production ranges. The canonical extracted body remains immutable.
- Tank vent 4221 350 5800 → 4221 350 5801. A sintered-material filter prevents dirt entering the valve/fuel system during pressure equalization. The left figure is the OLD vent with one through-hose; the right is the NEW vent with two hoses connected to INTEGRALLY MOULDED NIPPLES.
- New cap 4223 353 2300 has former-column -*-: remark 2 says the former cap was NOT A REPLACEMENT PART, not that no cap existed. Filter 0000 358 1810 is new. Valve 4114 353 1600 is UNCHANGED in both columns and appears as item 3 in both diagrams.
- Old hose item 4, 4130 358 0700, is 260 mm (10.2 inches) and has a new-column dash. New upper/side hose item 5 is 1110 141 8600, 135 mm (5.3 inches); new lower hose item 6 is 1119 141 8600, 106 mm (4.2 inches). Do not splice these lengths into a replacement 260 mm through-hose or infer a universal vent retrofit.
- Remark 1: old vent no longer factory-supplied. Remark 3: old 260 mm hose remains available for OLDER MACHINES AND OTHER SERIES. The closing earlier-TI pointer is 14.95 and imprint November 30, 1995; neither overrides the vent serial. No vent pressure rating or filter cleaning method is given.
- Historical TI evidence for TS 460, type 4221, not current supply, verified physical interchange or a complete repair procedure. No hardware operation was performed. Exact-model IPL links identify components only; no later IPL revision is backdated to 1995.
Source: TI 49/1995, p. 5 — TS 460 sintered-filter tank vent: two hoses replace the through-hose.
Part numbers (8)
- 4221 350 5800 — Tank vent with through-hoseoriginal · TS 460; historical configuration and supply limits in this note
- 4221 350 5801 — Tank vent with sintered filter and moulded nipplesnew · TS 460; historical configuration and supply limits in this note
- 4223 353 2300 — Cap; former cap not a replacement partnew · TS 460; historical configuration and supply limits in this note
- 0000 358 1810 — Sintered filternew · TS 460; historical configuration and supply limits in this note
- 4114 353 1600 — Valve; same numberretained · TS 460; historical configuration and supply limits in this note
- 4130 358 0700 — Hose 260 mm; retained older-machine supplyoriginal · TS 460; historical configuration and supply limits in this note
- 1110 141 8600 — Hose 135 mm, item 5new · TS 460; historical configuration and supply limits in this note
- 1119 141 8600 — Hose 106 mm, item 6new · TS 460; historical configuration and supply limits in this note
Wrong number or missing part for the TS 460? Report a correction →