Stihl 4221 · Section A · 1 of 20 · 35 parts
Engine housing, Cylinder
Fits TS 460.
Historical fitment & changes (17) — includes parts and conditions not shown on this drawing.
Parts (35)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4221 021 3000 | Engine housing | 1 |
| 2 | 4221 020 2100 | Crankcase | 1 |
| 3 | 4221 030 0400 | Crankshaft | 1 |
| 4 | 9503 003 0450 | Grooved ball bearing 6203 | 2 |
| 5 | 9456 621 4330 | Circlip 40x1.75 | 1 |
| 6 | 9640 003 1885 | Oil seal 17x40x7 Fitment / change note → → replaced by 9640 003 1888 TI 46/1996 | 1 |
| 7 | 9640 003 1745 | Oil seal 17x28x7 | 1 |
| 8 | 4221 029 2300 | Cylinder gasket | 1 |
| 9 | 9512 003 3140 | Needle cage 12x16x13 | 1 |
| 10 | 4221 020 1201 | Cylinder with piston Ø 48 mm Fitment / change note → | 1 |
| 12 | 4221 030 2000 | Piston Ø 48 mm | 1 |
| 13 | 1110 034 3003 NLA | Piston ring Ø 48x1.5 mm | 2 |
| 14 | 1108 034 1501 | Piston pin 12x8x33 | 1 |
| 15 | 9463 650 1200 | Snap ring 12x1 | 2 |
| 16 | 4221 020 9400 | Valve Fitment / change note → | 1 |
| 17 | 9022 341 1120 | Spline screw IS-M5x58 | 4 |
| 18 | 4221 129 0902 | Gasket | 1 |
| 19 | 4221 129 3000 | Sealing ring | 1 |
| 20 | 4221 120 2200 | Flange | 1 |
| 21 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 2 |
| 22 | 9022 341 1080 | Spline screw IS-M5x35 | 6 |
| 23 | 1124 149 0600 | Muffler gasket | 1 |
| 24 | 4221 140 0600 | Muffler | 1 |
| 25 | 9022 341 0975 NLA | Spline screw IS-M5x14 | 2 |
| 26 | 9331 630 0120 | Conical spring washer 5 Fitment / change note → | 2 |
| 27 | 4221 141 9000 | Screen | 1 |
| 28 | 4221 145 0605 | Deflecting plate | 1 |
| 29 | 9022 313 0610 | Spline screw IS-M4x6 | 6 |
| 30 | 1110 400 7005 | Spark plug Bosch WSR 6 F | 1 |
| 30 | 0000 400 7000 | Spark plug NGK BPMR7A | 1 |
| 31 | 0783 830 2000 | Tube of sealant Dirko HT red | 1 |
| 32 | 0000 967 3693 | Warning pictogram Filler cap | 1 |
| 40 | 4221 025 2200 | Plug Fitment / change note → | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4221 020 0200 | Engine Fitment / change note → | 1 |
| — | 4221 007 1050 | Set of gaskets | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · TS 460
TS460: decompression opens manually and closes on ignition
The valve reduces starting compression; combustion pressure closes it automatically. Three spring-loaded balls retain the two positions.
- The bulletin announces a new TS 460 Cutquik version, type 4221, with decompression valve. Page 1 photograph shows the accessible control on the shroud. Reduced rope-pulling effort and greater convenience are historical design claims, not measured starting-force values. No retrofit permission, original-part supersession, serial cutoff or release completion date is given.
- In illustrations 337TI002 and 337TI003, housing (1) surrounds the axially moving valve/piston (2), with a cone at its lower end. Three spring-loaded balls, spaced 120 degrees apart, hold the piston at upper and lower limits; callout 3 identifies the ball-retention region. The COMPLETE valve screws into the cylinder. Internal drawing labels do not identify separately orderable repair parts.
- Before starting, force valve (2) to the LOWER limit: the cone lifts from housing (1) and opens the escape hole (arrow in 337TI003). Some cylinder pressure escapes, leaving compression below the valve closing pressure. Only when the fuel-air mixture ignites does pressure rise enough to push the valve UP and seat the cone, sealing the hole. The upper drawing shows the closed position and the lower drawing the open position.
- No numerical opening/closing pressure, internal spring specification, ball size, machining tolerance or internal rebuilding procedure is supplied. The valve is not a substitute for normal starting instructions or a claim that a leaking engine is healthy.
- Historical TI guidance only; factory availability is historical, not current stock. Exact-model IPL links are navigation, not proof of unrestricted interchange. No hardware operation was performed.
Source: TI 14/1995, p. 1 · TI 14/1995, p. 2 · TI 14/1995, p. 3 — Complete bulletin: all text, illustrations, parts table, remarks and footer.
Part numbers (1)
- 4221 020 9400 — Complete decompression valveTS 460 new version · TS 460
Service note · TS 460
TS460: valve torque 14 Nm; use the specified plug for leak testing
Use a size-13 deep socket for the valve. TI14/1995 names temporary leak-test plug 1122 025 2200; the later IPL lists a different plug.
- The decompression valve can be installed and removed with a commercially available DEEP-WELL socket wrench, size 13. The printed tightening torque is 14 Nm for the DECOMPRESSION VALVE; it is NOT a cylinder-screw or leak-test-plug torque. No special socket order number, sealant or thread dimension is supplied.
- For a power-unit leak test, the TI advises TEMPORARILY removing the decompression valve and sealing its threaded bore with plug 1122 025 2200. The parts table marks this plug as a special accessory for service shops (comment 1), with a blank MAM cell. This is a test configuration, not a permanent deletion of decompression.
- The exact-model later TS 460 engine IPL lists plug 4221 025 2200 at key 40, whereas this service text AND its table specify 1122 025 2200. The different numbers remain an unresolved source/catalog discrepancy; no equivalence or supersession is inferred. The later plug is not silently substituted.
- The TI supplies no test pressure, vacuum, allowable leakage, duration or complete engine sealing procedure, and no plug torque. Those values remain unspecified rather than invented. No leak test or hardware action has been performed.
- Historical TI guidance only; factory availability is historical, not current stock. Exact-model IPL links are navigation, not proof of unrestricted interchange. No hardware operation was performed.
Source: TI 14/1995, p. 1 · TI 14/1995, p. 2 · TI 14/1995, p. 3 — Complete bulletin: all text, illustrations, parts table, remarks and footer.
Part numbers (2)
- 4221 020 9400 — Decompression valvedeep socket size 13; tightening torque 14 Nm · TS 460
- 1122 025 2200 — TI-specified temporary leak-test plugspecial accessory for service shops; MAM unspecified · TS 460
Service note · TS 460
TS460: new shroud includes grommet and both plates
Shroud 4221 080 1602 includes items 2–4: grommet, rating plate and instruction plate. Ordering minima are not installed quantities.
- The new replacement-parts table lists cylinder with piston 4221 020 1201 and decompression valve 4221 020 9400, each MAM 1. It does not name an old cylinder or old valve number, or state that every earlier TS 460 can be converted. The later IPL independently describes the cylinder as 48 mm; this TI does not state a bore dimension.
- Shroud 4221 080 1602 is item 1, MAM 1, and explicitly INCLUDES ITEMS 2, 3 AND 4: grommet 4221 084 7400 (item 2, MAM 10), rating plate 4221 967 1501 (item 3, MAM 10), instruction plate 0000 967 3673 (item 4, MAM 5). These MAM values are minimum ordering quantities, NOT ten grommets or plates installed per machine. The item numbers are table keys, not the valve drawing labels 1–3.
- The later ignition-system IPL retains the same shroud, grommet and model-plate numbers at keys 20, 23 and 24. Its instruction label 0000 967 3502 at key 27 differs from this TI instruction plate 0000 967 3673; no equivalence or supersession is asserted. The historical included plate is preserved despite its absence by that number in the later exact-model sheet.
- The separate plug row is the service-shop accessory covered by the leak-test note, NOT an item included in the shroud. Blank comments on the other rows do not supply an unstated old-stock or retrofit rule. No serial cutoff is printed.
- Last technical information 02.94 is bibliographic. Footer February 8, 1995, ©1995 Andreas Stihl, D1/MTK-sc Technical Documentation. All three original pages, photograph, two valve drawings, service notes and seven table rows are reviewed; issue 14.95 is not a production month.
- Historical TI guidance only; factory availability is historical, not current stock. Exact-model IPL links are navigation, not proof of unrestricted interchange. No hardware operation was performed.
Source: TI 14/1995, p. 1 · TI 14/1995, p. 2 · TI 14/1995, p. 3 — Complete bulletin: all text, illustrations, parts table, remarks and footer.
Part numbers (7)
- 4221 020 1201 — Cylinder with pistonnew; MAM 1 · TS 460
- 4221 020 9400 — Decompression valvenew; MAM 1 · TS 460
- 4221 080 1602 — Shroud; table item 1includes items 2–4; MAM 1 · TS 460
- 4221 084 7400 — Grommet; table item 2included; MAM 10 · TS 460
- 4221 967 1501 — Rating plate; table item 3included; MAM 10 · TS 460
- 0000 967 3673 — Instruction plate; table item 4included; MAM 5 · TS 460
- 1122 025 2200 — Plugseparate service-shop accessory; not shroud contents · TS 460
Service note · TS 460
TS 460 type 4221: introduction and control features
Cut-off saw introduction: 3.5 kW, 4.6 Nm, five AV buffers, slide control and semi-automatic belt tensioner.
- Page 1 identifies the new cut-off saw as TS 460, type 4221: engine output 3.5 kW (4.75 HP), maximum torque 4.6 Nm (0.46 kpm), and a headline weight of 11.3 kg (24.9 lb). The cover does not specify the weighing configuration; section 5.4 on page 8 supplies the configuration, preserved in the separate reviewed weight-and-dimensions note. This headline is not a weight claim for every wheel/fuel configuration.
- The introduction names an ergonomic top handle, semi-automatic V-belt tensioner, decompression valve and five-rubber-buffer anti-vibration system. The function-symbol slide control operates the controls with one hand; this is NOT permission to cut while holding the machine with only one hand.
- Claimed suitability for cart-mounted continuous duty and freehand cutting, fewer-component function groups, short repairs and reduced vibration are historical vendor descriptions, not project tests. Listed audiences span construction, utilities, highway/water authorities, building/steel trade, landscaping, fire and rescue; those audience lists confer no separate wheel approval.
- The cover photograph shows the complete machine, not an exploded assembly or a dimensioned/approved wheel specification. Page 1 provides no serial introduction threshold or separate component part numbers; type 4221 is not a complete orderable part number.
- Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.
Source: TI 43/1995, p. 1 — TS 460 type 4221: introduction and control features.
No additional parts-table entry added.
Service note · TS 460
TS 460 cylinder and piston: two rings and hookless retainers
Alloy cylinder and piston; two 1.5 mm rings, two hookless snap rings and two dust-lip shaft seals.
- Page 2 identifies cylinder (1) above the two-part crankcase (2). Two rotary shaft seals with additional dust lips seal the crankcase. Figure callout2 denotes the crankcase pair, not a third cylinder component.
- The cylinder is a special aluminium alloy with a galvanically applied wear-resistant special-alloy bore lining. The piston is also special aluminium alloy and has TWO piston rings, each 1.5 mm (0.06 in) thick; the piston pin is secured by TWO hookless snap rings.
- The source does not identify an alloy grade, coating trade name, piston/ring part numbers, ring end gap or installation orientation here. Do not infer interchange with a similar-displacement saw or treat the diagram as a measured drawing.
- Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.
Source: TI 43/1995, p. 2 — TS 460 cylinder and piston: two rings and hookless retainers.
No additional parts-table entry added.
Service note · TS 460
TS 460 crankshaft: conrod and big-end bearing not separately replaceable
Pressed crankshaft construction; split magnesium crankcase is distinct from the engine housing.
- The crankshaft uses two drop-forgings pressed onto the crankpin against twisting before finishing. The conrod and big-end bearing consequently CANNOT be replaced separately under this source description; it does not authorize pressing the crankshaft apart for a bearing substitution.
- The crankcase is split into two diecast-magnesium halves. The separate heavy-duty diecast-magnesium engine housing carries the power unit, ignition module, AV handle system, complete cast arm with cutting-wheel drive, and fuel tank with compensator reservoir. The lower page 2 drawing depicts that engine housing, not another crankcase half.
- The fuel-tank compensator reservoir and the diaphragm-carburetor compensator are distinct functions. A shared word does not make them the same part or justify connecting their hoses interchangeably. No housing/crankshaft part number or dimensional interchange is specified on this page.
- Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.
Source: TI 43/1995, p. 2 — TS 460 crankshaft: conrod and big-end bearing not separately replaceable.
No additional parts-table entry added.
Service note · TS 460
TS 460 decompression valve: manual opening and combustion closure
Axial piston and cone; three spring-loaded balls at 120°, not an electronic actuator.
- The complete decompression valve screws into the cylinder. Its housing (1) surrounds an axially moving piston (2) with a cone at the lower end; THREE spring-loaded balls (3), spaced 120° apart, retain the upper and lower piston positions.
- Before starting, pressing the piston to its lower holding position lifts the cone from the housing and opens the escape passage. Cranking expels some cylinder gas through the opening, reducing compression force and starter-rope effort; remaining cylinder pressure stays below the valve closing pressure.
- When a mixture capable of sustained combustion ignites, cylinder pressure exceeds the closing pressure and pushes the piston UP, seating the cone and sealing the opening. Manual opening and automatic combustion-pressure closure must not be reversed or described as electronic control.
- The upper sectional drawing 337TI002 shows the closed/up position; lower 337TI003 shows the open/down position and gas-exit arrow. Only one ball is visible in section; the prose specifies three at 120°. No numeric closing pressure or cone dimension is given.
- This is a functional description, not instructions to start or repair a connected machine. The installation torque and temporary leak-test plug guidance on pages 10–11 are preserved in the separate reviewed decompression-valve service note; no guessed torque or pressure is added.
- Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.
Source: TI 43/1995, p. 4 — TS 460 decompression valve: manual opening and combustion closure.
No additional parts-table entry added.
Service note · TS 460
TS 460 fuel reservoir, five AV buffers and forward exhaust
0.96 litre tank; separate compensator reservoir returns fuel under negative pressure.
- The fuel tank holds 0.96 litres / 2.02 pt (960 ccm). Its large filler opening is on top of the housing; the TI describes filling in the normal working position, for example with the STIHL filling system. Ease-of-filling wording is not permission to refuel a running or hot engine.
- Tank and compensator reservoir are installed inside the engine housing. Excess tank pressure sends fuel through a connecting hose into the reservoir; negative pressure returns it to the tank. This reservoir is NOT the clean-air pressure compensator on the carburetor.
- The claim that this arrangement prevents fuel or fuel-vapour escape is the historical functional description, not an emissions certification or a leak test performed by this project. Do not backdate the separate 47/1999 tank-vent revision to this 1995 description.
- FIVE rubber buffers on the engine housing separate the handle system from the engine unit and all other assemblies attached to that housing. Vibration reduction is a vendor description, not a measured acceleration value.
- The generously sized exhaust muffler is described as reducing noise effectively, with exhaust gases emitted to the FRONT. This paragraph gives no decibel rating, spark-arrestor approval or muffler part number.
- Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.
Source: TI 43/1995, p. 5 — TS 460 fuel reservoir, five AV buffers and forward exhaust.
No additional parts-table entry added.
Service note · TS 460
TS 460 engine data: spindle, working, limit and clutch speeds differ
72.4 cm³, 48 × 40 mm; 4900 spindle, 9100 working and 9600 limiting rpm.
- The single-cylinder two-stroke engine is listed with specially impregnated cylinder bore, displacement 72.4 cm³ (4.42 cu. in), bore 48 mm (1.89 in) and stroke 40 mm (1.57 in). Output to DIN 70020 is 3.5 kW (4.75 HP); maximum torque 4.6 Nm (0.46 kpm) occurs at 5500 rpm.
- The table distinguishes MAXIMUM SPINDLE speed 4900 rpm, maximum permissible engine speed 9600 rpm with electronic limiter, maximum working speed 9100 rpm, average idle 2500 rpm, and clutch engagement approximately 3200 rpm. These are not interchangeable speed settings.
- The crankshaft is three-part, drop-forged, supported in heavy-duty deep-groove ball bearings, with needle cages at the connecting-rod small and big ends. Conrod length is 70 mm (2.75 in). This construction description does not contradict the earlier prohibition on replacing the pressed crankshaft conrod/big-end bearing separately.
- The centrifugal clutch has no linings and is 80 mm (3.15 in) in diameter. Starter is single-pawl with automatic rope rewind. No current measurement or operating-speed adjustment was performed.
- Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.
Source: TI 43/1995, p. 7 — TS 460 engine data: spindle, working, limit and clutch speeds differ.
No additional parts-table entry added.
Service note · TS 460
TS 460 seal and piston tools: sleeves, puller jaws and retaining tools
Distinct clutch-side seal protection, jaw sets and piston tools; tool numbers are not installed parts.
- Page 9 lists press sleeve 1127 893 2400 for pressing in the rotary shaft seal and assembly sleeve 1122 893 4600 for protecting the seal on the CLUTCH SIDE. Do not infer the same assembly sleeve for both shaft ends.
- Rotary-shaft-seal puller 0000 890 4400 has separately listed jaws No. 3.1 + 4 (0000 893 3706) and jaws No. 6 (0000 893 3711). The table does not allocate each jaw to a specific shaft end or say that the base puller includes both sets.
- Assembly pin 1108 893 4700 fits the piston pin; strap retainer 0000 893 2600 tensions the piston rings; wooden assembly block 1108 893 4800 positions the piston; assembly tool 12, 5910 890 2212, inserts snap rings in the piston eye. Tool designation 12 is not a quantity.
- Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.
Source: TI 43/1995, p. 9 — TS 460 seal and piston tools: sleeves, puller jaws and retaining tools.
Part numbers (9)
- 1127 893 2400 — Press sleevespecified · TS 460 servicing; application-specific tools, not installed components
- 1122 893 4600 — Clutch-side seal protection sleevespecified · TS 460 servicing; application-specific tools, not installed components
- 0000 890 4400 — Rotary shaft seal pullerspecified · TS 460 servicing; application-specific tools, not installed components
- 0000 893 3706 — Puller jaws No. 3.1 + 4specified · TS 460 servicing; application-specific tools, not installed components
- 0000 893 3711 — Puller jaws No. 6specified · TS 460 servicing; application-specific tools, not installed components
- 1108 893 4700 — Piston-pin assembly pinspecified · TS 460 servicing; application-specific tools, not installed components
- 0000 893 2600 — Piston-ring strap retainerspecified · TS 460 servicing; application-specific tools, not installed components
- 1108 893 4800 — Wooden piston assembly blockspecified · TS 460 servicing; application-specific tools, not installed components
- 5910 890 2212 — Assembly tool 12 for piston-eye snap ringsspecified · TS 460 servicing; application-specific tools, not installed components
Service note · TS 460
TS 460 leakage-test tools: pressure tester, vacuum pump and sealing accessories
Crankcase and carburetor tester differ from the crankcase-only vacuum pump.
- Carburetor/crankcase tester 1106 850 2905 is listed for both circuits, with connector 0000 855 9200 and fuel line 1110 141 8600 as subordinate entries. Vacuum pump 0000 850 3501 is listed for CRANKCASE leakage testing, not as a carburetor vacuum-test specification.
- Sealing plate 0000 855 8106 closes the EXHAUST PORT for leakage testing. Test flange 1119 850 4200 is listed with bushings 0000 963 1008 and screws 9043 319 8100. These associations do not establish supplied kit contents or quantities.
- The tool table supplies no test pressure, hold time or pass/fail decay limit. Page 7 pressure values remain distinct by circuit; page 10 adds the temporary decompression-bore plug. This is not a complete leakage-test procedure.
- Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.
Source: TI 43/1995, p. 9 — TS 460 leakage-test tools: pressure tester, vacuum pump and sealing accessories.
Part numbers (8)
- 1106 850 2905 — Carburetor and crankcase testerspecified · TS 460 leakage-test servicing tools
- 0000 855 9200 — Tester connectorspecified · TS 460 leakage-test servicing tools
- 1110 141 8600 — Tester fuel linespecified · TS 460 leakage-test servicing tools
- 0000 850 3501 — Crankcase vacuum pumpspecified · TS 460 leakage-test servicing tools
- 0000 855 8106 — Exhaust-port sealing platespecified · TS 460 leakage-test servicing tools
- 1119 850 4200 — Leak-test flangespecified · TS 460 leakage-test servicing tools
- 0000 963 1008 — Test-flange bushingsspecified · TS 460 leakage-test servicing tools
- 9043 319 8100 — Test-flange screwsspecified · TS 460 leakage-test servicing tools
Service note · TS 460
TS 460 decompression valve service: 13 mm long socket and temporary test plug
14 Nm valve torque; plug 4221 025 2200 temporarily seals the bore for leakage testing.
- The decompression valve is removed/installed with a standard LONG 13 mm across-flats socket insert to ISO 2725 or DIN 3124. Its tightening torque is 14 Nm. This socket specification does not make the size-13 flywheel-nut insert a verified substitute.
- For engine leakage testing, the TI advises temporarily removing the decompression valve and sealing its threaded bore with plug 4221 025 2200. TEMPORARY testing substitution is not authorization to delete the valve permanently. No separate plug torque is supplied.
- If starting is necessary during repair/maintenance, the TI requires national safety regulations AND the safety instructions in the Owner’s Manual. The exact TS 460 owner-manual dependency is not established in the bounded retained-source inventory; do not turn this TI into complete startup or loaded-test instructions.
- Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.
Source: TI 43/1995, p. 10 — TS 460 decompression valve service: 13 mm long socket and temporary test plug.
Part numbers (1)
- 4221 025 2200 — Temporary decompression-bore sealing plugspecified · TS 460 engine leakage test; not a permanent valve replacement
Service note · TS 460
TS 460 engine torques: joint-specific values and blank thread cells
Nm values retained by component; clutch and valve blank thread cells are not inherited from adjacent rows.
- Page 11 prints the heading 5.4 Tightening torques. All values below are Nm. Socket-head screws: cylinder/crankcase IS-M5×58×22 — 10; crankcase/engine housing IS-M5×35×22 — 10; spacer flange IS-M5×20 — 10; cast arm/engine housing IS-M5×20 — 10.
- Clutch — 40 Nm; hexagon nut M10×1, starter wheel — 40 Nm; collar nut M8×1, flywheel — 25 Nm. The CLUTCH row leaves fastener and thread cells BLANK: do not inherit IS-M5×20 from the spacer-flange row. No thread direction is specified here.
- Filter base/engine housing IS-M5×14 — 6 Nm; connector/carburetor/flange IS-M5×58×35 — 5 Nm. Spark plug M14×1.25 — 27.5 Nm; decompression valve — 14 Nm. The valve row leaves its thread cell BLANK; M14×1.25 belongs only to the spark plug.
- Thread dimensions are fastener descriptions, not orderable part numbers. Values are scoped to these 1995 joints and do not backdate the later exact-model IPL.
- Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.
Source: TI 43/1995, p. 11 — TS 460 engine torques: joint-specific values and blank thread cells.
No additional parts-table entry added.
Service note · TS 460
TS 460 torque footnotes: washers and muffler Loctite 243 are row-specific
Housing cover 6 Nm and ignition module 8 Nm need washers; muffler/engine joint needs adhesive AND tensioning washer.
- Housing cover/engine housing IS-M5×14 — 6 Nm and ignition module IS-M5×20 — 8 Nm carry remark 1: ENSURE A WASHER IS USED. The source does not identify a washer number for these two rows.
- Muffler/cylinder IS-M5×14 — 10 Nm has NO footnotes. Muffler/engine housing IS-M5×35 — 10 Nm carries BOTH remarks 2 and 3: secure with adhesive 0786 111 1101 (Loctite 243) AND use tensioning washer 9331 630 0120. Do not transfer these two requirements to every 10 Nm screw.
- Other rows: fan cover IS-M5×20 — 6 Nm; deflector/muffler IS-M4×6 — 2.5 Nm; tensioner IS-M5×14 — 4 Nm; short-circuit wire/ground IS-M4×6 — 2.5 Nm.
- The note says adhesive-secured screws release more easily with GENTLE heating using a blow-drier and warns of GREAT CARE WHEN HEATING PLASTIC COMPONENTS. It gives no temperature or heating duration and does not approve open-flame heating.
- Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.
Source: TI 43/1995, p. 11 — TS 460 torque footnotes: washers and muffler Loctite 243 are row-specific.
Part numbers (2)
- 0786 111 1101 — Loctite 243 threadlocking adhesivespecified · TS 460 muffler/engine-housing screw connection
- 9331 630 0120 — Tensioning washerspecified · TS 460 muffler/engine-housing IS-M5×35 joint; remark 3
Service note · TS 460
TS 460 decompression valve: 13 mm socket, 14 Nm and temporary test plug
Press to open; automatic closing follows first ignition, not merely starter movement.
- The decompression valve is opened MANUALLY BY PRESSING its button and closes automatically when the fuel-air mixture FIRST IGNITES. Reduced chamber compression lowers starter-rope force. TI14/1995 is the retained mechanical-design/function cross-reference, already dispositioned; this batch does not invent a new valve mechanism.
- Removal/installation uses a 13 mm DEEP WELL socket; stated torque is 14 Nm (10 ft. lbs). For power-unit leak testing the TI advises temporarily removing the valve and sealing its screw hole with plug 4221 025 2200. This is a temporary leak-test seal, not a substitute for restoring the required configuration.
- No test pressure, hold time or leak threshold is supplied here. The same plug is separately specified for a replacement cylinder fitted to a machine without a decompression valve; those two uses must not be confused with the plastic COVER cap.
- Historical TI evidence for TS 460, type 4221, not current supply, verified physical interchange or a complete repair procedure. No hardware operation was performed. Exact-model IPL links identify components only; no later IPL revision is backdated to 1995.
Source: TI 49/1995, p. 2 — TS 460 decompression valve: 13 mm socket, 14 Nm and temporary test plug.
Part numbers (1)
- 4221 025 2200 — Cylinder screw-hole plug; temporary leak-test sealspecified · TS 460; historical configuration and supply limits in this note
Conditional replacement · TS 460
TS 460 replacement cylinder and cover: plug and cap serve different openings
New cylinder and cover only from factory; non-decompression machines need both appropriate closures.
X 32 675 830 — Introduction from this printed machine number for TS 460 and this modification only; not a model-identification range or a cutoff for other changes.
- Cylinder with piston changes 4221 020 1200 → 4221 020 1201; decompression valve 4221 020 9400 and plug 4221 025 2200 have dashes in the former column. After general quick-starting introduction only the new cylinder version is supplied. On a machine WITHOUT decompression valve, fit plug 4221 025 2200 in the cylinder screw hole INSTEAD OF the valve.
- Cover changes 4221 080 1600 → 4221 080 1602. It can also be used without decompression valve IF its valve opening is sealed by cap 4221 084 7100. The page 2 diagram crosses out the valve in this configuration and points to the separate cover opening/cap; the plastic cap is NOT the threaded cylinder plug.
- The new cover includes items 5–8: spout 4221 084 7400, rating plate 4221 967 1501, information plate 0000 967 3673 and cap 4221 084 7100; their former columns are dashes. The rating plate is plastic and CLIPPED into place. No plate identity data or universal cover compatibility is supplied.
- Page 3 remark 1 applies to the former cylinder and cover: no longer available from factory. These are historical supply statements. All other parts as before; the quick-starting cutoff is X 32 675 830, not either of the later carburetor or separate vent serials.
- Historical TI evidence for TS 460, type 4221, not current supply, verified physical interchange or a complete repair procedure. No hardware operation was performed. Exact-model IPL links identify components only; no later IPL revision is backdated to 1995.
Source: TI 49/1995, p. 2 · TI 49/1995, p. 3 — TS 460 replacement cylinder and cover: plug and cap serve different openings.
Part numbers (10)
- 4221 020 1200 — Cylinder with pistonoriginal · TS 460; historical configuration and supply limits in this note
- 4221 020 1201 — Cylinder with piston, valve/plug provisionnew · TS 460; historical configuration and supply limits in this note
- 4221 020 9400 — Decompression valvenew · TS 460; historical configuration and supply limits in this note
- 4221 025 2200 — Cylinder plug for no-valve configurationspecified · TS 460; historical configuration and supply limits in this note
- 4221 080 1600 — Coveroriginal · TS 460; historical configuration and supply limits in this note
- 4221 080 1602 — Cover including items 5–8new · TS 460; historical configuration and supply limits in this note
- 4221 084 7400 — Spoutnew · TS 460; historical configuration and supply limits in this note
- 4221 967 1501 — Clipped plastic rating platenew · TS 460; historical configuration and supply limits in this note
- 0000 967 3673 — Information platenew · TS 460; historical configuration and supply limits in this note
- 4221 084 7100 — Cap closing cover opening without valvespecified · TS 460; historical configuration and supply limits in this note
Historical fitment · TS 460
TS 460 clutch-side oil seal: elastic sheath and changed outer diameter
9640 003 1885 (17 x 40 x 7) → 9640 003 1888 (17 x 39.9 x 7).
- Section 2 is headed SHORT BLOCK although the contents calls it power unit. The CLUTCH-SIDE crankshaft oil seal changes in the near future to a version with a RUBBER-ELASTIC OUTER SHEATH. It does not specify the same change on the other side of the crankshaft.
- The three-row summary retains short block 4221 020 0200. Included old seal item 2 is 9640 003 1885, printed17 x 40 x 7; new item 3 is 9640 003 1888, printed17 x 39.9 x 7. Preserve39.9 versus40 and the separate dashed cells; do not round away the dimensional change or infer a universal seal substitute.
- Introduction is a RUNNING CHANGE, no numeric serial stated. Both unchanged short blocks and former seals remain factory-available while stocks last, per distinct remarks 1/2. Other parts as before. Neither block number nor carburetor serial identifies a loose block's installed seal.
- The exactTS460 engine sheet retains short-block number 4221 020 0200 but is later catalog navigation. No seal installation depth, tooling, torque or permission to alter the housing bore is given by TI 46.
- This is historical source guidance, not present stock or a verified physical interchange. Later IPL sheets are navigation, not a reconstruction of the 1996 configuration. No hardware operation was performed.
Source: TI 46/1996, p. 2 — TS 460 clutch-side oil seal: elastic sheath and changed outer diameter.
Part numbers (3)
- 4221 020 0200 — Short blockUnchanged number; clutch-side seal revised · TS 460; old stock may retain old seal
- 9640 003 1885 — Crankshaft oil seal17 x 40 x 7Original clutch-side seal · TS 460; stocks-only historical supply
- 9640 003 1888 — Crankshaft oil seal17 x 39.9 x 7New rubber-elastic-sheathed seal · TS 460 clutch side only
Wrong number or missing part for the TS 460? Report a correction →