← TS 460

Stihl 4221 · Section F · 6 of 20 · 27 parts

Air filter

Fits TS 460.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110101112131415161718192202122233456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (27)

PosPart numberDescriptionQty
1 4221 124 3401 Filter base 1
2 9022 341 1400 Spline screw IS-M6x40 1
3 9022 341 0975 NLA Spline screw IS-M5x14 4
4 4221 140 1800 Auxiliary filter 1
5 4221 140 4400 Air filter 1
6 4221 141 0310 Prefilter 1
7 4221 140 1000 Filter cover 1
8 4221 140 9500 Slotted nut 1
9 4221 149 0502 Gasket 1
10 4221 129 0903 Gasket 2
11 4221 120 0652 Carburetor HS-275B 1
11 4221 120 0650 Carburetor HS-276D 1
11 4221 120 0651 Carburetor HS-275B 1
12 4221 141 3400 Connector 1
13 9307 021 0120 Washer 5.3 1
14 9075 478 4115 Pan head self-tapping screw IS-D5x16 1
15 4221 141 5400 Hose 1
16 9022 341 1120 Spline screw IS-M5x58 2
17 4221 140 2501 Elbow 1
18 9771 021 2575 Hose clip Ø 34x5 1
19 4221 141 2400 Support plate Fitment / change note → 1
20 4221 123 7500 Grommet 1
21 4221 123 7501 Grommet 1
22 4221 121 6150 Choke lever 1
23 not sold separately Choke slide not available as a separate item 1
Not numbered on the diagram — assemblies, kits and options
— 4221 007 1002 Air filter kit option 1
— 4221 007 1050 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · TS 460

TS 460 compensator: air-filter soiling does not call for H-screw correction

Clean-air pressure reference reduces fuel delivery as the filter soils; no invented carburetor variant.

  • The thermally insulated, dust-proof diaphragm carburetor sits in the engine housing. A hose connects its metering-chamber end-cover connector to the intake manifold, exposing the outside of the control diaphragm to the same pressure as the clean-air side of the air filter.
  • As filter soiling reduces airflow, pressure falls both in the carburetor venturi and outside the control diaphragm. The diaphragm moves outward and the needle valve partly closes, reducing fuel delivery and preventing the mixture from becoming too rich.
  • The stated effect eliminates the need for further adjustment of the HIGH-speed screw as the air filter becomes increasingly soiled. It does NOT mean the carburetor can never need setup or repair, and is not permission to run without filters or ignore declining performance.
  • Page 2 describes later onset of performance decline, longer cleaning intervals and air-filter life, with optimum performance restored by cleaning the prefilter or replacing the main filter cartridge. These are vendor claims; no numeric cleaning interval or guaranteed recovery for a damaged engine is supplied.
  • The page 3 pressure diagram labels 1 air filter, 2 carburetor, 3 cylinder, 4 fuel tank; Pi internal pressure, Pa external pressure, Pr pressure in the metering chamber. These labels are not pressure-test setpoints. The section names no carburetor model; do not backdate later HS-276D/HS-275B IPL variants to this description.
  • Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.

Source: TI 43/1995, p. 2 · TI 43/1995, p. 3 — TS 460 compensator: air-filter soiling does not call for H-screw correction.

No additional parts-table entry added.

Service note · TS 460

TS 460 air filters: matched prefilter, main and auxiliary elements

Three-stage filtration and central locking nut; clean prefilter versus replace main cartridge.

  • Combustion air enters between the carburetor-box cover and shroud, described as the lowest-dust intake location on the machine. The page 3 exploded filter view labels 1 prefilter, 2 main filter, 3 auxiliary filter; all three are matched for filtration efficiency and air permeability.
  • The original page 3 bullets specify extremely uniform pore size, pleat position and filter-paper strength, plus high compressive strength and dimensional accuracy of the filter cartridges. These two bullets are interleaved in the indexed text; the original layout establishes the grouping.
  • The central locking nut secures the filter cover and permits removal for cleaning the filter system. Page 2 distinguishes cleaning the PREFILTER from replacing the MAIN filter cartridge. It does not authorize washing the paper main cartridge, discarding the auxiliary element or substituting an unmatched filter.
  • Engine protection is conditional on prescribed servicing and maintenance; the TI does not supply a cleaning chemical, cleaning interval or full maintenance sequence in this section. No omitted instructions are invented. Material specifications in section 5.2 remain for the later technical-data review.
  • Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.

Source: TI 43/1995, p. 2 · TI 43/1995, p. 3 — TS 460 air filters: matched prefilter, main and auxiliary elements.

No additional parts-table entry added.

Service note · TS 460

TS 460 leak-test references and historical carburetor settings

Crankcase 0.5 bar pressure/vacuum; carburetor 0.8 bar gauge, H/L about one turn.

  • Page 7 specifies crankcase leakage-test gauge pressure pe = 0.5 bar and vacuum pn = 0.5 bar. The vacuum value is a magnitude under vacuum, NOT a second positive-pressure test. Carburetor leakage-test gauge pressure is separately pe = 0.8 bar.
  • These are distinct circuits/test conditions, not allowable pressure to apply to every hose or reservoir. The page supplies no permissible leak-down rate or hold duration; sealing/tool arrangements and decompression-valve handling on pages 9–10 are preserved in separate reviewed leakage-tool and decompression-service notes. No pressure or vacuum test was performed.
  • The carburetor is an all-position diaphragm type with integral fuel pump. High-speed screw H and low-speed screw L each back off APPROXIMATELY ONE TURN, starting at their seats. This historical baseline is not permission to force the screws tight or a final running adjustment for all later carburetor versions.
  • Fuel is brand-name regular gasoline and brand-name two-stroke engine oil. The TI specifies 1:50 when using STIHL two-stroke oil 1:50, versus 1:25 for other brand-name two-stroke oil. Those two conditional historical ratios are not merged into a universal present-day recommendation.
  • Tank capacity is repeated as 0.96 l / 2.02 pt (960 ccm). Air-filter materials are a felt prefilter, paper-cartridge main filter and flock-coated plastic auxiliary filter. These material identities do not authorize washing the paper element or omitting a stage.
  • Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.

Source: TI 43/1995, p. 7 — TS 460 leak-test references and historical carburetor settings.

No additional parts-table entry added.

Historical fitment · TS 460

TS 460 intake manifold: spring-steel support presses outward

Support 4221 141 2400 reinforces the manifold against collapse.

  • A support is to be introduced in the near future as a functional improvement, reinforcing the intake manifold to help prevent collapse. It is made of SPRING STEEL and MUST BE FITTED SO IT PRESSES THE MANIFOLD AGAINST THE HOUSING DUCT FROM THE INSIDE.
  • Drawing 337TI007KN shows the support in the duct opening with an arrow at its lower edge; it does not provide bending dimensions, a force value or an alternative component. Preserve the stated outward support relationship rather than treating the arrow as a part number.
  • The single-row summary adds 4221 141 2400 with a dash in the old-version column. Introduction is a RUNNING CHANGE, without numeric serial or a new manifold part number. No automatic all-variant retrofit or carburetor-bound production cutoff is specified.
  • This is historical source guidance, not present stock or a verified physical interchange. Later IPL sheets are navigation, not a reconstruction of the 1996 configuration. No hardware operation was performed.

Source: TI 46/1996, p. 2 — TS 460 intake manifold: spring-steel support presses outward.

Part numbers (1)
  • 4221 141 2400 — Spring-steel manifold supportNew support · TS 460; press manifold against housing duct from inside

Wrong number or missing part for the TS 460? Report a correction →