← TS 460

Stihl 4221 · Section E · 5 of 20 · 33 parts

Ignition system

Fits TS 460.

Parts diagrams →

Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121313141516171819220212223242627339440415678889
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (33)

PosPart numberDescriptionQty
1 4221 400 1200 Flywheel Fitment / change note → → replaced by 4223 400 1200 TI 53/1999 1
2 0000 955 0802 Collar nut M8x1 1
3 4223 400 1300 Ignition module Fitment / change note → → replaced by 4223 400 1302 TI 2/2002 1
4 not sold separately Ignition lead 360 mm not available as a separate item 1
5 0000 448 1201 Lead retainer 1
6 0000 989 1010 Grommet 1
7 9022 341 1019 Spline screw IS-M5x20 3
8 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 11
9 4221 442 0400 Insulating hose 1
10 1128 405 1000 Spark plug boot 1
11 0000 998 0604 Torsion spring 1
12 4221 084 1600 Cover 1
13 0000 989 0804 Grommet 2
14 0751 030 8958 Terminal socket 4.8-1 no longer available from factory 1
15 0751 030 8953 NLA Terminal socket 4.8-1 no longer available from factory 1
16 0751 030 8470 Grommet no longer available from factory 1
17 1121 405 1900 NLA Support 1
18 not sold separately Lead 550 mm / 21.7'' not available as a separate item 1
19 4221 080 3100 Fan cover 1
20 4221 080 1602 Shroud Fitment / change note → 1
21 4221 084 6600 Insert 1
22 4126 182 6210 Collar screw 2
23 4221 084 7400 Grommet Fitment / change note → 1
24 4221 967 1501 Model plate TS 460 Fitment / change note → 1
26 4221 140 1900 Carburetor box cover 1
27 0000 967 3502 Instruction label 1
39 9291 021 0120 Washer 5.3 3
40 4221 084 7100 Cap Fitment / change note → 1
41 0000 974 1000 Round head rivet 3x6 2
Not numbered on the diagram — assemblies, kits and options
— 0000 405 0600 NLA Ignition lead 1 m not illustratedoption 1
— 0000 930 2251 Ignition lead 10 m not illustratedoption 1
— 4221 440 1101 Short circuit wire 1
— 0751 010 1110 Lead 10 m / 33' not illustratedoption 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · TS 460

TS 460: series 4221 replacement ignition assignment

4223 400 1300 with flywheel 4221 400 1200; lead length not specified.

  • Printed series 4221. Use 4223 400 1300 with flywheel 4221 400 1200.
  • The TS 460 ignition-lead length cells are blank. Do not borrow the adjacent TS 400 value of 370 mm (14 9/16 in); no cut length is established here.
  • TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
  • Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
  • Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
  • Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
  • Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.

Source: TI 1/1999, p. 1 · TI 1/1999, p. 3 — 1.1 general restrictions and 1.2.2 power-tool assignments.

Part numbers (2)
  • 4223 400 1300 — Replacement ignition moduleAssigned component · TS 460, printed series 4221, listed combination only
  • 4221 400 1200 — Assigned flywheelRequired pairing · TS 460, printed series 4221

Service note · TS 460

TS460: new shroud includes grommet and both plates

Shroud 4221 080 1602 includes items 2–4: grommet, rating plate and instruction plate. Ordering minima are not installed quantities.

  • The new replacement-parts table lists cylinder with piston 4221 020 1201 and decompression valve 4221 020 9400, each MAM 1. It does not name an old cylinder or old valve number, or state that every earlier TS 460 can be converted. The later IPL independently describes the cylinder as 48 mm; this TI does not state a bore dimension.
  • Shroud 4221 080 1602 is item 1, MAM 1, and explicitly INCLUDES ITEMS 2, 3 AND 4: grommet 4221 084 7400 (item 2, MAM 10), rating plate 4221 967 1501 (item 3, MAM 10), instruction plate 0000 967 3673 (item 4, MAM 5). These MAM values are minimum ordering quantities, NOT ten grommets or plates installed per machine. The item numbers are table keys, not the valve drawing labels 1–3.
  • The later ignition-system IPL retains the same shroud, grommet and model-plate numbers at keys 20, 23 and 24. Its instruction label 0000 967 3502 at key 27 differs from this TI instruction plate 0000 967 3673; no equivalence or supersession is asserted. The historical included plate is preserved despite its absence by that number in the later exact-model sheet.
  • The separate plug row is the service-shop accessory covered by the leak-test note, NOT an item included in the shroud. Blank comments on the other rows do not supply an unstated old-stock or retrofit rule. No serial cutoff is printed.
  • Last technical information 02.94 is bibliographic. Footer February 8, 1995, ©1995 Andreas Stihl, D1/MTK-sc Technical Documentation. All three original pages, photograph, two valve drawings, service notes and seven table rows are reviewed; issue 14.95 is not a production month.
  • Historical TI guidance only; factory availability is historical, not current stock. Exact-model IPL links are navigation, not proof of unrestricted interchange. No hardware operation was performed.

Source: TI 14/1995, p. 1 · TI 14/1995, p. 2 · TI 14/1995, p. 3 — Complete bulletin: all text, illustrations, parts table, remarks and footer.

Part numbers (7)
  • 4221 020 1201 — Cylinder with pistonnew; MAM 1 · TS 460
  • 4221 020 9400 — Decompression valvenew; MAM 1 · TS 460
  • 4221 080 1602 — Shroud; table item 1includes items 2–4; MAM 1 · TS 460
  • 4221 084 7400 — Grommet; table item 2included; MAM 10 · TS 460
  • 4221 967 1501 — Rating plate; table item 3included; MAM 10 · TS 460
  • 0000 967 3673 — Instruction plate; table item 4included; MAM 5 · TS 460
  • 1122 025 2200 — Plugseparate service-shop accessory; not shroud contents · TS 460

Service note · TS 460

TS 460 ignition module: outside flywheel and electronic speed limiter

Breakerless magnetic-induction ignition; module removal does not require flywheel removal.

  • Page 3 describes electronically controlled, breakerless magnetic-induction ignition. The control electronics and ignition coil are integrated in the ignition module, together with electronic speed limiting intended to prevent exceeding maximum permissible speed.
  • The ignition module is on the OUTSIDE of the flywheel; the flywheel does NOT need to be removed to dismantle the ignition module. This access statement does not remove the need for an appropriate service procedure.
  • No module part number, test resistance, air gap, spark-plug approval or numerical limiter speed is specified in this paragraph. Section 5.3 and the page 7 speed table are covered by the separate reviewed ignition-data and engine-speed notes; do not substitute numbers from another machine.
  • Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.

Source: TI 43/1995, p. 3 — TS 460 ignition module: outside flywheel and electronic speed limiter.

No additional parts-table entry added.

Service note · TS 460

TS 460 ignition data: timing inch range is internally inconsistent

0.2–0.5 mm air gap; 2.8–3.2 mm timing before UDC at 8000 rpm, conflicting inch text retained.

  • Transistorized breakerless magneto ignition has integrated control and electronic speed limiter. The specified air gap is 0.2–0.5 mm (0.008–0.02 in).
  • Ignition timing is printed as 2.8–3.2 mm (0.11–0.02 in) before UDC at n = 8000 rpm. The ORIGINAL SCAN contains the inconsistent 0.02 in upper endpoint; this is not merely an indexed-text error. 3.2 mm converts to approximately 0.126 in, but that calculation is NOT a corrected vendor specification.
  • Interference-suppressed spark plugs are Bosch WSR 6 F OR NGK BPMR 7 A. Electrode gap is 0.5 mm (0.02 in), thread M 14 × 1.25, thread length 9.5 mm (0.37 in) and heat range 200 as printed. The heat-range figure is not translated into another manufacturer numbering system.
  • Ignition lead length is 360 mm (14 3/16 in). The source does not provide a module part number or authorize applying these timings to another model. No spark test or timing adjustment was performed.
  • Historical TI 43/1995 description of TS 460, type 4221, not current supply, measured performance or a complete repair procedure. No hardware operation was performed. The sheet link identifies the exact model/component only; no later IPL revision is backdated to 1995.

Source: TI 43/1995, p. 7 — TS 460 ignition data: timing inch range is internally inconsistent.

No additional parts-table entry added.

Conditional replacement · TS 460

TS 460 replacement cylinder and cover: plug and cap serve different openings

New cylinder and cover only from factory; non-decompression machines need both appropriate closures.

X 32 675 830 — Introduction from this printed machine number for TS 460 and this modification only; not a model-identification range or a cutoff for other changes.

  • Cylinder with piston changes 4221 020 1200 → 4221 020 1201; decompression valve 4221 020 9400 and plug 4221 025 2200 have dashes in the former column. After general quick-starting introduction only the new cylinder version is supplied. On a machine WITHOUT decompression valve, fit plug 4221 025 2200 in the cylinder screw hole INSTEAD OF the valve.
  • Cover changes 4221 080 1600 → 4221 080 1602. It can also be used without decompression valve IF its valve opening is sealed by cap 4221 084 7100. The page 2 diagram crosses out the valve in this configuration and points to the separate cover opening/cap; the plastic cap is NOT the threaded cylinder plug.
  • The new cover includes items 5–8: spout 4221 084 7400, rating plate 4221 967 1501, information plate 0000 967 3673 and cap 4221 084 7100; their former columns are dashes. The rating plate is plastic and CLIPPED into place. No plate identity data or universal cover compatibility is supplied.
  • Page 3 remark 1 applies to the former cylinder and cover: no longer available from factory. These are historical supply statements. All other parts as before; the quick-starting cutoff is X 32 675 830, not either of the later carburetor or separate vent serials.
  • Historical TI evidence for TS 460, type 4221, not current supply, verified physical interchange or a complete repair procedure. No hardware operation was performed. Exact-model IPL links identify components only; no later IPL revision is backdated to 1995.

Source: TI 49/1995, p. 2 · TI 49/1995, p. 3 — TS 460 replacement cylinder and cover: plug and cap serve different openings.

Part numbers (10)
  • 4221 020 1200 — Cylinder with pistonoriginal · TS 460; historical configuration and supply limits in this note
  • 4221 020 1201 — Cylinder with piston, valve/plug provisionnew · TS 460; historical configuration and supply limits in this note
  • 4221 020 9400 — Decompression valvenew · TS 460; historical configuration and supply limits in this note
  • 4221 025 2200 — Cylinder plug for no-valve configurationspecified · TS 460; historical configuration and supply limits in this note
  • 4221 080 1600 — Coveroriginal · TS 460; historical configuration and supply limits in this note
  • 4221 080 1602 — Cover including items 5–8new · TS 460; historical configuration and supply limits in this note
  • 4221 084 7400 — Spoutnew · TS 460; historical configuration and supply limits in this note
  • 4221 967 1501 — Clipped plastic rating platenew · TS 460; historical configuration and supply limits in this note
  • 0000 967 3673 — Information platenew · TS 460; historical configuration and supply limits in this note
  • 4221 084 7100 — Cap closing cover opening without valvespecified · TS 460; historical configuration and supply limits in this note

Conditional replacement · TS 460

TS 460 ignition module standardization: continuous introduction, no serial cutoff

4221 400 1305 → 4223 400 1300; old module while stocks last.

  • Section 3 says ignition module 4221 400 1305 will be replaced by 4223 400 1300 in the FORESEEABLE FUTURE for parts standardization. The table repeats the pair and says including all parts as before.
  • Introduction is CONTINUOUSLY, with NO SERIAL CUTOFF. Do not borrow X 33 417 473 from the carburetor section on the same page or the other two cutoffs elsewhere in this TI. The former module remains available from factory only WHILE STOCKS LAST.
  • This TS 460 assignment does not establish universal compatibility based on the new module’s 4223 prefix; no flywheel pairing, timing or operating-speed change is specified here.
  • Historical TI evidence for TS 460, type 4221, not current supply, verified physical interchange or a complete repair procedure. No hardware operation was performed. Exact-model IPL links identify components only; no later IPL revision is backdated to 1995.

Source: TI 49/1995, p. 4 — TS 460 ignition module standardization: continuous introduction, no serial cutoff.

Part numbers (2)
  • 4221 400 1305 — Ignition module; while stocks lastoriginal · TS 460; historical configuration and supply limits in this note
  • 4223 400 1300 — Standardized ignition modulenew · TS 460; historical configuration and supply limits in this note

Wrong number or missing part for the TS 460? Report a correction →