← TS 400

Stihl 4223 · Section B · 2 of 22 · 29 parts

Cast arm, Clutch

Fits TS 400.

Parts diagrams →

Historical fitment & changes (7) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151617181922021222323232424242526272829334567789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (29)

PosPart numberDescriptionQty
1 4223 701 0200 Cast arm 1
2 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 5
3 1125 790 9906 Annular buffer 1125/06 Fitment / change note → 2
4 4221 660 0400 Belt tensioner 1
5 4221 664 2100 Clamping lever 1
6 4221 664 4200 Cover 1
7 9022 341 0980 Spline screw IS-M5x16 4
8 4223 162 1000 Cover washer 1
9 4223 160 3000 Cover washer option 1
10 1125 160 2005 Clutch → replaced by 4238 120 0600 TI 34/2008 1
11 1128 162 0806 Clutch shoe 3
12 0000 997 5815 Tension spring 3
13 1128 162 3000 Retainer 3
14 0000 961 1003 Ring 1
15 4223 700 2500 V-belt pulley 1
16 9503 003 6310 Grooved ball bearing 6200-2RS 1
17 9456 621 3310 Circlip 30x1.2 1
18 0000 958 0824 Washer 1
19 4223 195 0600 Starter cup 1
20 9210 261 1140 Hexagon nut M8x1 1
21 9490 000 7851 Narrow V-belt 10/6x859 1
22 4223 791 1900 Handlebar support 1
23 9022 341 1280 Spline screw IS-M6x16 3
24 1125 791 7306 Plug 3
25 4223 790 1750 Handlebar 1
26 9074 478 4435 Pan head self-tapping screw IS-P6x19 2
27 4223 791 7600 Support 1
28 9022 341 1050 Spline screw IS-M5x25 2
29 1125 790 9906 Annular buffer 1125/06 Fitment / change note → 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · TS 400

TS 400 V-belt tensioner: initial setting versus retensioning

Spring tensioning uses a nut for initial setting; routine retensioning does not readjust it.

  • For initial tensioning, turn the tensioning nut to the tensioning position; spring force then tensions the V-belt automatically. Source calls the mechanism already proven on TS 460 but does NOT assert identical components or a TS460-to-TS400 retrofit.
  • For RETENSIONING, loosen and retighten the THREE HEX BOLTS on the V-belt guard; there is NO NEED TO ADJUST THE TENSIONING NUT. Source attributes prevention of excessive belt tension and premature wear to constant spring force.
  • The figure shows the spring/linkage and adjustment tool, not a numeric belt-force specification. No nut angle, direction, bolt torque, belt ordering number or complete dismantling procedure is printed in this section.
  • Historical TI guidance for the 1995 TS 400, type 4223, only. Later exact-model IPL sheets are navigation aids, not evidence that every later variant has the original configuration. No hardware operation was performed.

Source: TI 37/1995, p. 4 — TS 400 V-belt tensioner: initial setting versus retensioning.

No additional parts-table entry added.

Service note · TS 400

TS 400 AV system: five rubber buffers

Five buffers isolate the handle system from the crankcase-connected assemblies.

  • The AV system comprises FIVE RUBBER BUFFERS secured to the crankcase. It isolates the handle system from the power unit and all other assemblies connected to the crankcase, to reduce vibration transmitted to the handles.
  • This is a system-level count, not five pieces of any one ordering number. The paragraph provides no buffer hardness, individual positions, vibration measurement or authorization to mix buffer revisions. Later sheets do not expand the 1995 configuration claim.
  • Historical TI guidance for the 1995 TS 400, type 4223, only. Later exact-model IPL sheets are navigation aids, not evidence that every later variant has the original configuration. No hardware operation was performed.

Source: TI 37/1995, p. 5 — TS 400 AV system: five rubber buffers.

No additional parts-table entry added.

Service note · TS 400

TS 400 power unit: engine speeds and leakage-test pressures

Spindle speed, governed engine speed and idle are different specifications.

  • Section 6.1: single-cylinder two-stroke engine with specially impregnated cylinder bore; displacement 64.1 cm³ (3.9 cu in), bore 49 mm (1.93 in), stroke 34 mm (1.34 in). Power to ISO 7293 is 3.2 kW (4.4 HP); maximum torque 4.1 Nm (0.41 kpm) AT 6500 rpm. No coating chemistry is identified.
  • Maximum SPINDLE speed 4800 rpm; maximum acceptable ENGINE speed 9700 rpm with electronic speed limitation; mean IDLE 2500 rpm. These are not interchangeable settings. Unlined centrifugal clutch diameter 76 mm (2.99 in), engaging at APPROXIMATELY 3500 rpm.
  • Three-part drop-forged crankshaft; heavy-duty deep-groove ball bearing for crankshaft and needle cages at crankpin big-end and piston pin. Single-pawl starter with automatic rope rewind; rope diameter 3.5 mm (1/8 inch), no rope length supplied.
  • Crankcase leakage testing: excess pressure 0.5 bar and negative pressure 0.5 bar, the latter a VACUUM MAGNITUDE, not a second positive-pressure setting. No duration or allowable leak-down rate is printed here. Carburetor pressure is separately specified as 0.8 bar on page 7.
  • Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.

Source: TI 37/1995, p. 6 — TS 400 power unit: engine speeds and leakage-test pressures.

No additional parts-table entry added.

Service note · TS 400

TS 400 tightening torques: starter, handles, filter and muffler

Identical screw sizes have different joint-specific torques.

  • All values in Nm. Groove-headed IS-DG 4 x 14 starter cover: 1.8, with Loctite 242/243. Socket-head IS-DG 4 x 15 handle moulding/handle: 1.8; same size stop-linkage mount: 1.8. IS-DGM 5 x 20 handlebar/handlebar mount: 8.0 (DGM designation retained as printed); IS-DG 5 x 20 tank housing left/right: 7.5. M 5 nut filter base/carburetor: 3.5.
  • Socket-head IS-M 5 x 16: tensioner cover/cast arm 4.5; handlebar/tank housing 8.0; air baffle/crankcase 4.5; muffler/crankcase 10.0; muffler/cylinder 10.0. Do not derive torque solely from thread size.
  • Socket-head IS-M 5 x 20: cast arm/crankcase 10.0; filter base/tank housing 6.0; filter case/filter base 4.0 (the source misspells the last label Fitler). Thread/size descriptions are not ordering numbers. See the DG procedure note for thread re-engagement and adhesive removal.
  • Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.

Source: TI 37/1995, p. 7 · TI 37/1995, p. 8 — TS 400 tightening torques: starter, handles, filter and muffler.

No additional parts-table entry added.

Service note · TS 400

TS 400 tightening torques: crankcase, AV joints and rotating parts

Left-hand clutch and pulley threads retain their separate torque values.

  • All values in Nm. Socket-head IS-M 5 x 20: shroud/tank housing 6.0; crankcase left/right 10.0; fan cover/tank housing 6.0; starter cover/cast arm 6.0; cylinder/crankcase 10.0; ignition module/crankcase 8.0 WITH WASHER UNDER THE HEAD.
  • IS-M 5 x 25 support/handlebar/tank housing: 8.0. IS-M 6 x 16 AV element joints: cast arm/handlebar 6.0; tank housing/cast arm 6.0; tank housing/crankcase LEFT 6.0. Grub screw M 5 x 55 tank housing/carburetor: 4.0.
  • Collar nut M 8 x 1 flywheel: 30.0; hex nut M 8 x 1 starter wheel: 23.0; driver M 12 x 1 L clutch: 40.0; spark plug M 14 x 1.25: 27.5; hex nut M 10 L V-belt pulley/bearing: 37.5; decompression valve: 14.0. The L markings identify LEFT-HAND THREADS, not alternative metric pitch values. No decompression-valve thread size is printed.
  • This completes the continued table, not a universal torque chart. Use the named joint and the companion DG/adhesive precautions; no source ordering numbers are supplied by this table.
  • Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.

Source: TI 37/1995, p. 8 — TS 400 tightening torques: crankcase, AV joints and rotating parts.

No additional parts-table entry added.

Service note · TS 400

TS 400 crankshaft locking and clutch tools: strip only

0000 893 5903 is mandatory; stop bolts can damage the piston.

  • ONLY locking strip 0000 893 5903 may be used to lock the TS 400 crankshaft. The source explicitly warns that one of the stop bolts from the STIHL special-tool set WILL DAMAGE THE PISTON. The separate page 8 accessory name locking pin does not authorize a stop bolt.
  • Long size 21 insert 5910 893 5616 releases/tightens clutch; assembly hook 5910 890 2800 disengages clutch springs. These uses do not establish universal clutch-tool fitment.
  • Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.

Source: TI 37/1995, p. 9 — TS 400 crankshaft locking and clutch tools: strip only.

Part numbers (3)
  • 0000 893 5903 — Crankshaft locking strip; exclusive TS400 instructionsource-listed service tool or accessory · TS 400; TS 400 crankshaft locking and clutch tools: strip only
  • 5910 893 5616 — Size21 long insert for clutchsource-listed service tool or accessory · TS 400; TS 400 crankshaft locking and clutch tools: strip only
  • 5910 890 2800 — Assembly hook for clutch springssource-listed service tool or accessory · TS 400; TS 400 crankshaft locking and clutch tools: strip only

Historical fitment · TS 400

TS 400 AV buffers: four harder buffers, one unchanged

From X 35 033 958: three 1125 790 9910 plus one 1124 790 9905; retain one 1125 790 9906.

X 35 033 958 — TI 45 AV-system/front-handle mounting introduction; not the continuously introduced tank-vent change.

  • TI 45/1996 names TS 400 type 4223. FOUR of FIVE rubber buffers become harder from X 35 033 958; the ring buffer in the front handle mount, CLUTCH SIDE TOP, is unchanged. No hardness value is provided.
  • Table item 1 keeps 1125 790 9906 but remark 1 reduces its QUANTITY FROM FOUR TO ONE. Item 2 adds THREE 1125 790 9910 with a dash in the old-number cell. Item 3 replaces ONE 1121 790 9912 with 1124 790 9905. These are location/quantity-specific changes, not universal supersession of 1125 790 9906.
  • The AV drawing 338TI009GM shows one callout 1 at the top front-handle mount, three callout 2 positions and one callout 3. The prose, summary and drawing support the five-position distinction; do not change quantities on the later IPL to match a historical diagram.
  • Remark 2 keeps original 1121 790 9912 available for OTHER MODELS, not named here. The later exactTS400 cast-arm sheet still has 1125 790 9906 at more than one row; this later inventory is preserved, not forced into the1996 four-to-one configuration.
  • This is historical source guidance, not present stock or a verified physical interchange. Later IPL sheets are navigation, not a reconstruction of the 1996 configuration. No hardware operation was performed.

Source: TI 45/1996, p. 1 — TS 400 AV buffers: four harder buffers, one unchanged.

Part numbers (4)
  • 1125 790 9906 — Ring bufferUnchanged number; quantity reduced4 to to1 · TS 400 clutch-side top front-handle mount remains unchanged
  • 1125 790 9910 — Harder ring bufferThree new buffers · TS 400 item 2; from stated AV serial
  • 1121 790 9912 — Ring bufferOriginal single buffer · TS 400 item 3; historical other-model supply retained
  • 1124 790 9905 — Harder ring bufferNew single buffer · TS 400 item 3; from stated AV serial

Wrong number or missing part for the TS 400? Report a correction →