Stihl 4223 · Section A · 1 of 22 · 29 parts
Crankcase
Fits TS 400.
Historical fitment & changes (13) — includes parts and conditions not shown on this drawing.
Parts (29)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4223 020 2900 | Crankcase | 1 |
| 2 | 0000 988 5211 | Connector | 1 |
| 3 | 9503 003 0341 | Grooved ball bearing 6202 | 1 |
| 4 | 9640 003 1570 | Oil seal 15x24x7 | 1 |
| 5 | 0000 988 8600 | Sleeve | 2 |
| 6 | 4223 020 2601 | Crankcase | 1 |
| 7 | 4223 020 2600 | Crankcase → replaced by 4223 020 2601 TI 2/2002 | 1 |
| 8 | 9503 003 0450 | Grooved ball bearing 6203 | 1 |
| 9 | 9640 003 1745 | Oil seal 17x28x7 | 1 |
| 10 | 4223 030 0400 | Crankshaft | 1 |
| 11 | 4223 029 0500 | Gasket | 1 |
| 12 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 8 |
| 13 | 9512 003 2340 | Needle cage 10x14x13 | 1 |
| 14 | 4223 020 1200 | Cylinder with piston Ø 49 mm | 1 |
| 15 | 4223 030 2000 | Piston Ø 49 mm | 1 |
| 16 | 1110 034 1500 | Piston pin 10x6x32 | 1 |
| 17 | 1127 034 3006 | Piston ring Ø 49x1.5 mm | 2 |
| 18 | 9463 650 1000 | Snap ring 10 | 1 |
| 19 | 4223 020 9400 | Decompression valve | 1 |
| 20 | 4223 029 2301 | Cylinder gasket | 1 |
| 21 | 1110 400 7005 | Spark plug Bosch WSR 6 F | 1 |
| 21 | 0000 400 7000 | Spark plug NGK BPMR7A | 1 |
| 22 | 4223 140 0601 | Muffler | 1 |
| 23 | 4223 141 9000 | Screen | 1 |
| 24 | 4223 141 6600 | Clip | 1 |
| 25 | 1125 149 0601 | Muffler gasket | 1 |
| 26 | not sold separately | Air guide shroud no longer available from factory | 1 |
| 27 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 6 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4223 007 1050 | Set of gaskets Fitment / change note → | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · TS 400
TS 400 introduction: equipment and conflicting weights
The introduction says 18.6 lb; the specified dry 300-mm machine is 8.9 kg (19.6 lb).
- TI37/1995 introduces TS 400, type 4223. Page 1 calls it the lightest STIHL cut-off saw and prints 18.6 lb. Section 6.5 on page 8 instead gives 8.9 kg (19.6 lb), WITHOUT FUEL, complete with the 300-mm (12-inch) cutting-wheel attachment but WITHOUT THE CUTTING WHEEL. The one-pound discrepancy is unresolved; no undocumented configuration difference or corrected mass is inferred.
- Equipment list: long-term air filter with compensator, Quickstart with ElastoStart and decompression valve, AV handle system, semi-automatic V-belt tensioner, tank with expansion reservoir, electronic magneto ignition with speed limitation and light aluminium guard. No numeric serial changeover is printed in these introductory sections.
- The cover photograph and marketing descriptions concern TS 400. Claims about reliability, low service needs and suitability for construction, rental, municipal, utility, materials, steel and rescue work are source-era descriptions, not independent performance testing or certification. No ordering number is supplied for the illustrated complete machine.
- Historical TI guidance for the 1995 TS 400, type 4223, only. Later exact-model IPL sheets are navigation aids, not evidence that every later variant has the original configuration. No hardware operation was performed.
Source: TI 37/1995, p. 1 · TI 37/1995, p. 2 · TI 37/1995, p. 8 — TS 400 introduction: equipment and conflicting weights.
No additional parts-table entry added.
Service note · TS 400
TS 400 decompression valve: manual opening, automatic closure
Three spring-loaded balls retain the piston; ignition pressure closes the valve.
- The complete valve screws into the cylinder. Housing (1), axially moving piston (2) with lower cone, and THREE SPRING-LOADED BALLS (3) at 120-degree intervals form the described mechanism. Balls hold upper and lower limit positions; diagram numbers are not ordering numbers.
- Before starting, push the piston to its lower limit so the cone lifts off the housing and opens the valve, reducing compression and starting effort. The source says cylinder pressure exceeds closing pressure only when a combustible fuel/air charge first ignites; piston then rises and its cone closes the passage.
- The two cross-sections show closed and open states; the outward arrow in the lower drawing identifies the open relief path. No numeric opening/closing pressure, valve repair procedure or interchange with another cylinder is supplied by these sections.
- Historical TI guidance for the 1995 TS 400, type 4223, only. Later exact-model IPL sheets are navigation aids, not evidence that every later variant has the original configuration. No hardware operation was performed.
Source: TI 37/1995, p. 3 · TI 37/1995, p. 4 — TS 400 decompression valve: manual opening, automatic closure.
No additional parts-table entry added.
Service note · TS 400
TS 400 power unit: engine speeds and leakage-test pressures
Spindle speed, governed engine speed and idle are different specifications.
- Section 6.1: single-cylinder two-stroke engine with specially impregnated cylinder bore; displacement 64.1 cm³ (3.9 cu in), bore 49 mm (1.93 in), stroke 34 mm (1.34 in). Power to ISO 7293 is 3.2 kW (4.4 HP); maximum torque 4.1 Nm (0.41 kpm) AT 6500 rpm. No coating chemistry is identified.
- Maximum SPINDLE speed 4800 rpm; maximum acceptable ENGINE speed 9700 rpm with electronic speed limitation; mean IDLE 2500 rpm. These are not interchangeable settings. Unlined centrifugal clutch diameter 76 mm (2.99 in), engaging at APPROXIMATELY 3500 rpm.
- Three-part drop-forged crankshaft; heavy-duty deep-groove ball bearing for crankshaft and needle cages at crankpin big-end and piston pin. Single-pawl starter with automatic rope rewind; rope diameter 3.5 mm (1/8 inch), no rope length supplied.
- Crankcase leakage testing: excess pressure 0.5 bar and negative pressure 0.5 bar, the latter a VACUUM MAGNITUDE, not a second positive-pressure setting. No duration or allowable leak-down rate is printed here. Carburetor pressure is separately specified as 0.8 bar on page 7.
- Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.
Source: TI 37/1995, p. 6 — TS 400 power unit: engine speeds and leakage-test pressures.
No additional parts-table entry added.
Service note · TS 400
TS 400 tightening torques: starter, handles, filter and muffler
Identical screw sizes have different joint-specific torques.
- All values in Nm. Groove-headed IS-DG 4 x 14 starter cover: 1.8, with Loctite 242/243. Socket-head IS-DG 4 x 15 handle moulding/handle: 1.8; same size stop-linkage mount: 1.8. IS-DGM 5 x 20 handlebar/handlebar mount: 8.0 (DGM designation retained as printed); IS-DG 5 x 20 tank housing left/right: 7.5. M 5 nut filter base/carburetor: 3.5.
- Socket-head IS-M 5 x 16: tensioner cover/cast arm 4.5; handlebar/tank housing 8.0; air baffle/crankcase 4.5; muffler/crankcase 10.0; muffler/cylinder 10.0. Do not derive torque solely from thread size.
- Socket-head IS-M 5 x 20: cast arm/crankcase 10.0; filter base/tank housing 6.0; filter case/filter base 4.0 (the source misspells the last label Fitler). Thread/size descriptions are not ordering numbers. See the DG procedure note for thread re-engagement and adhesive removal.
- Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.
Source: TI 37/1995, p. 7 · TI 37/1995, p. 8 — TS 400 tightening torques: starter, handles, filter and muffler.
No additional parts-table entry added.
Service note · TS 400
TS 400 tightening torques: crankcase, AV joints and rotating parts
Left-hand clutch and pulley threads retain their separate torque values.
- All values in Nm. Socket-head IS-M 5 x 20: shroud/tank housing 6.0; crankcase left/right 10.0; fan cover/tank housing 6.0; starter cover/cast arm 6.0; cylinder/crankcase 10.0; ignition module/crankcase 8.0 WITH WASHER UNDER THE HEAD.
- IS-M 5 x 25 support/handlebar/tank housing: 8.0. IS-M 6 x 16 AV element joints: cast arm/handlebar 6.0; tank housing/cast arm 6.0; tank housing/crankcase LEFT 6.0. Grub screw M 5 x 55 tank housing/carburetor: 4.0.
- Collar nut M 8 x 1 flywheel: 30.0; hex nut M 8 x 1 starter wheel: 23.0; driver M 12 x 1 L clutch: 40.0; spark plug M 14 x 1.25: 27.5; hex nut M 10 L V-belt pulley/bearing: 37.5; decompression valve: 14.0. The L markings identify LEFT-HAND THREADS, not alternative metric pitch values. No decompression-valve thread size is printed.
- This completes the continued table, not a universal torque chart. Use the named joint and the companion DG/adhesive precautions; no source ordering numbers are supplied by this table.
- Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.
Source: TI 37/1995, p. 8 — TS 400 tightening torques: crankcase, AV joints and rotating parts.
No additional parts-table entry added.
Service note · TS 400
TS 400 crankshaft locking and clutch tools: strip only
0000 893 5903 is mandatory; stop bolts can damage the piston.
- ONLY locking strip 0000 893 5903 may be used to lock the TS 400 crankshaft. The source explicitly warns that one of the stop bolts from the STIHL special-tool set WILL DAMAGE THE PISTON. The separate page 8 accessory name locking pin does not authorize a stop bolt.
- Long size 21 insert 5910 893 5616 releases/tightens clutch; assembly hook 5910 890 2800 disengages clutch springs. These uses do not establish universal clutch-tool fitment.
- Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.
Source: TI 37/1995, p. 9 — TS 400 crankshaft locking and clutch tools: strip only.
Part numbers (3)
- 0000 893 5903 — Crankshaft locking strip; exclusive TS400 instructionsource-listed service tool or accessory · TS 400; TS 400 crankshaft locking and clutch tools: strip only
- 5910 893 5616 — Size21 long insert for clutchsource-listed service tool or accessory · TS 400; TS 400 crankshaft locking and clutch tools: strip only
- 5910 890 2800 — Assembly hook for clutch springssource-listed service tool or accessory · TS 400; TS 400 crankshaft locking and clutch tools: strip only
Service note · TS 400
TS 400 seal and bearing tools: jaws and distinct drift pins
1119 and 4119 drift pins have different jobs despite their matching suffix.
- Press sleeve 1127 893 2400 presses in rotary shaft seal; assembly sleeve 1122 893 4600 protects the CLUTCH-SIDE rotary shaft seal. Extractor 0000 890 4400 removes shaft seals, with jaws Nos 3.1+4 under 0000 893 3706 and jaws No 6 under 0000 893 3711. Do not turn jaw labels into quantities or assign an unprinted side to each jaw set.
- Pliers A 10 0811 611 8200: OUTER circlip on thrust washer. Pliers C 19 0811 641 8380: INNER circlip in spindle bearing and crankshaft.
- Drift pin 1119 893 7200 presses the NEEDLE SLEEVE into/out of the V-belt pulley. Distinct drift pin 4119 893 7200 forces out DEEP-GROOVE BALL BEARINGS in the spindle bearing. The first four digits must not be normalized as a typo.
- Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.
Source: TI 37/1995, p. 9 — TS 400 seal and bearing tools: jaws and distinct drift pins.
Part numbers (9)
- 1127 893 2400 — Seal press sleevesource-listed service tool or accessory · TS 400; TS 400 seal and bearing tools: jaws and distinct drift pins
- 1122 893 4600 — Clutch-side seal protection sleevesource-listed service tool or accessory · TS 400; TS 400 seal and bearing tools: jaws and distinct drift pins
- 0000 890 4400 — Rotary shaft seal extractorsource-listed service tool or accessory · TS 400; TS 400 seal and bearing tools: jaws and distinct drift pins
- 0000 893 3706 — Extractor jaws Nos3.1+4source-listed service tool or accessory · TS 400; TS 400 seal and bearing tools: jaws and distinct drift pins
- 0000 893 3711 — Extractor jaws No6source-listed service tool or accessory · TS 400; TS 400 seal and bearing tools: jaws and distinct drift pins
- 0811 611 8200 — Pliers A10, outer circlipsource-listed service tool or accessory · TS 400; TS 400 seal and bearing tools: jaws and distinct drift pins
- 0811 641 8380 — Pliers C19, inner circlipsource-listed service tool or accessory · TS 400; TS 400 seal and bearing tools: jaws and distinct drift pins
- 1119 893 7200 — Needle-sleeve drift pinsource-listed service tool or accessory · TS 400; TS 400 seal and bearing tools: jaws and distinct drift pins
- 4119 893 7200 — Spindle-bearing drift pinsource-listed service tool or accessory · TS 400; TS 400 seal and bearing tools: jaws and distinct drift pins
Service note · TS 400
TS 400 assembly tools: piston, flywheel and rope bush
The stand, piston supports and flywheel extractor are distinct tools.
- Assembly stand 5910 890 3100 holds machine for repair. Extractor 1116 893 0800 removes flywheel. Assembly pin 1108 893 4700 assembles piston pin; strap retainer 0000 893 2600 tensions piston rings; wooden block 1108 893 4800 positions piston.
- Assembly tool 10 5910 890 2210 inserts snap rings in piston boss; assembly tool 0000 890 2201 flares rope guide bush. The numeric tool 10 designation is not a count of ten tools.
- Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.
Source: TI 37/1995, p. 9 — TS 400 assembly tools: piston, flywheel and rope bush.
Part numbers (7)
- 5910 890 3100 — Assembly standsource-listed service tool or accessory · TS 400; TS 400 assembly tools: piston, flywheel and rope bush
- 1116 893 0800 — Flywheel extractorsource-listed service tool or accessory · TS 400; TS 400 assembly tools: piston, flywheel and rope bush
- 1108 893 4700 — Piston-pin assembly pinsource-listed service tool or accessory · TS 400; TS 400 assembly tools: piston, flywheel and rope bush
- 0000 893 2600 — Piston-ring strap retainersource-listed service tool or accessory · TS 400; TS 400 assembly tools: piston, flywheel and rope bush
- 1108 893 4800 — Wooden piston assembly blocksource-listed service tool or accessory · TS 400; TS 400 assembly tools: piston, flywheel and rope bush
- 5910 890 2210 — Assembly tool10 for piston snap ringssource-listed service tool or accessory · TS 400; TS 400 assembly tools: piston, flywheel and rope bush
- 0000 890 2201 — Rope guide bush flaring toolsource-listed service tool or accessory · TS 400; TS 400 assembly tools: piston, flywheel and rope bush
Service note · TS 400
TS 400 test tools: pressure, vacuum and ignition gauge
The test flange and exhaust sealing plate have different roles.
- Carburetor/crankcase tester 1106 850 2905 for leakage testing, listed with connector 0000 855 9200 and fuel line 1110 141 8600. Vacuum pump 0000 850 3501 tests crankcase leakage.
- Sealing plate 0000 855 8106 closes exhaust outlet for leakage tests; test flange 1128 850 4200 is listed for leakage testing. No pressure/hold-time instructions are supplied by this tool roster itself.
- Setting gauge 1111 890 6400 sets ignition-module/flywheel air gap. Crimping tool 5910 890 8210 fits connectors to electrical leads; neither tool is a replacement ignition component.
- Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.
Source: TI 37/1995, p. 9 — TS 400 test tools: pressure, vacuum and ignition gauge.
Part numbers (8)
- 1106 850 2905 — Carburetor/crankcase testersource-listed service tool or accessory · TS 400; TS 400 test tools: pressure, vacuum and ignition gauge
- 0000 855 9200 — Tester connectorsource-listed service tool or accessory · TS 400; TS 400 test tools: pressure, vacuum and ignition gauge
- 1110 141 8600 — Tester fuel linesource-listed service tool or accessory · TS 400; TS 400 test tools: pressure, vacuum and ignition gauge
- 0000 850 3501 — Crankcase vacuum pumpsource-listed service tool or accessory · TS 400; TS 400 test tools: pressure, vacuum and ignition gauge
- 0000 855 8106 — Exhaust sealing platesource-listed service tool or accessory · TS 400; TS 400 test tools: pressure, vacuum and ignition gauge
- 1128 850 4200 — Leakage-test flangesource-listed service tool or accessory · TS 400; TS 400 test tools: pressure, vacuum and ignition gauge
- 1111 890 6400 — Ignition air-gap gaugesource-listed service tool or accessory · TS 400; TS 400 test tools: pressure, vacuum and ignition gauge
- 5910 890 8210 — Electrical connector crimping toolsource-listed service tool or accessory · TS 400; TS 400 test tools: pressure, vacuum and ignition gauge
Service note · TS 400
TS 400 torque tools: two ranges and warning-device versions
0302 and 0312 include optical/acoustic warnings; DG screws require a torque wrench.
- Size 13 insert 5910 893 5608 is for flywheel nut; size 17 insert 5910 893 5610 for starter-wheel nut. These sizes are not inferred from nut thread diameters.
- Torque wrenches 5910 890 0301/02 cover 0.5–18 Nm; 5910 890 0311/12 cover 6–80 Nm. The slash shorthand expands to 0301 and 0302, and 0311 and 0312 respectively. ONLY versions 5910 890 0302 and 5910 890 0312 are identified as having an OPTICAL/ACOUSTIC WARNING DEVICE. Torque wrench use is mandatory for DG screws.
- Insert 0812 542 2104, designation printed 1-5 x 120 x 6.3, is for socket-head screws with STAR-SHAPED RECESS. Tee-handle screwdriver 5910 890 2400, printed QI-5 x 150, is for HEX SOCKET-HEAD screws. Preserve those distinct recess descriptions; do not silently correct uncertain designation typography into another tool size.
- Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.
Source: TI 37/1995, p. 9 — TS 400 torque tools: two ranges and warning-device versions.
Part numbers (8)
- 5910 893 5608 — Size13 flywheel nut insertsource-listed service tool or accessory · TS 400; TS 400 torque tools: two ranges and warning-device versions
- 5910 893 5610 — Size17 starter-wheel nut insertsource-listed service tool or accessory · TS 400; TS 400 torque tools: two ranges and warning-device versions
- 5910 890 0301 — Torque wrench 0.5–18 Nmsource-listed service tool or accessory · TS 400; TS 400 torque tools: two ranges and warning-device versions
- 5910 890 0302 — Torque wrench 0.5–18 Nm, optical/acoustic warningsource-listed service tool or accessory · TS 400; TS 400 torque tools: two ranges and warning-device versions
- 5910 890 0311 — Torque wrench 6–80 Nmsource-listed service tool or accessory · TS 400; TS 400 torque tools: two ranges and warning-device versions
- 5910 890 0312 — Torque wrench 6–80 Nm, optical/acoustic warningsource-listed service tool or accessory · TS 400; TS 400 torque tools: two ranges and warning-device versions
- 0812 542 2104 — Star-recess screw insertsource-listed service tool or accessory · TS 400; TS 400 torque tools: two ranges and warning-device versions
- 5910 890 2400 — Hex socket tee-handle screwdriversource-listed service tool or accessory · TS 400; TS 400 torque tools: two ranges and warning-device versions
Service note · TS 400
TS 400 ZS tool rework: three holes and template orientation
Use marks 13 for type 4223; the top-view drawing and underside template are not interchangeable.
- Assembly tool ZS 5910 890 2220 removes crankshaft; screw sleeve 5910 893 2420 installs it. Section 7.1.1 says future supplied ZS tools will already have THREE ADDITIONAL 5.5-mm (7/32-inch) HOLES for TS 400. Existing tools lacking them may be reworked; no dated delivery cutoff or changed ordering number is given.
- Source directs photocopying the LAST-PAGE SCALE TEMPLATE, cutting it out carefully and placing it on the UNDERSIDE of the tool flange to mark holes. Stamp 13 on TOP beside each of the three new holes and above the new edge identification notch. Page 10 figure 338 TI 004 is a TOP VIEW; page 12 template 338 BB 005 is the separate marking reference. Do not mirror one into the other by guesswork.
- Template labels 12 = TYPE 1128 and 13 = TYPE 4223, with three marked positions for each and arrows to edge notches. These are type-pattern identifiers, NOT drill diameters or TS 400 serial numbers. The existing 12 pattern is not a substitute for the new 13 pattern.
- Original template is locally available, but a responsive web image, screenshot or resized print is NOT VERIFIED 1:1. Verify physical reproduction scale and orientation against the original/tool before any rework; no hole coordinates or flange diameter are printed and none is inferred from browser pixels. This review performs no machining.
- Last-page footer dates this TI to April 25,1995 at Waiblingen; the review date is separate. No new physical fit or machining accuracy has been demonstrated.
- Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.
Source: TI 37/1995, p. 9 · TI 37/1995, p. 10 · TI 37/1995, p. 12 — TS 400 ZS tool rework: three holes and template orientation.
Part numbers (2)
- 5910 890 2220 — Assembly tool ZS; requires TS400 hole patternsource-listed service tool or accessory · TS 400; TS 400 ZS tool rework: three holes and template orientation
- 5910 893 2420 — Crankshaft-installation screw sleevesource-listed service tool or accessory · TS 400; TS 400 ZS tool rework: three holes and template orientation
Service note · TS 400
TS 400 service accessories: grease, lead stock and gasket set
Bulk ignition lead is 10 metres; the installed lead specification is 370 mm.
- Section 7.2 lists STIHL multi-purpose grease 0781 120 1109 for the HIGH-VOLTAGE ARBOR ON THE IGNITION MODULE. Do not generalize the stated grease use to every bearing or gasket.
- HTR ignition lead 0000 930 2251 is 10-m stock; section 6.3 separately specifies installed ignition lead length 370 mm. Gasket set 4223 007 1050 and sealing panel 0457 281 4103 are also listed; no gasket contents or specific panel placement is printed.
- Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.
Source: TI 37/1995, p. 7 · TI 37/1995, p. 10 — TS 400 service accessories: grease, lead stock and gasket set.
Part numbers (4)
- 0781 120 1109 — STIHL multi-purpose grease for ignition high-voltage arborsource-listed service tool or accessory · TS 400; TS 400 service accessories: grease, lead stock and gasket set
- 0000 930 2251 — HTR ignition lead,10-m stocksource-listed service tool or accessory · TS 400; TS 400 service accessories: grease, lead stock and gasket set
- 4223 007 1050 — Gasket setsource-listed service tool or accessory · TS 400; TS 400 service accessories: grease, lead stock and gasket set
- 0457 281 4103 — Sealing panelsource-listed service tool or accessory · TS 400; TS 400 service accessories: grease, lead stock and gasket set
Service note · TS 400
TS 400 repair-time table: unmatched numeric strip retained
Twenty time values accompany seventeen repair codes; individual assignments are unresolved.
- Section 8 requires national safety regulations and Owner’s Manual instructions if the Cutquik must run during repair/maintenance. Repair times assume TRAINED PROFESSIONALS WITH A PROPERLY EQUIPPED SERVICE SHOP; they are not novice deadlines. Times are tenths of an hour: 0.1 hour = 6 minutes, not decimal minutes.
- The text says the TS 400 table may be transferred into the STIHL repair-time table; the dashed cut-out numeric strip is headed TS 400 / TS 460. This shared heading is not evidence of component interchange.
- Original scan has SEVENTEEN labeled repair codes but TWENTY numeric time values with different vertical spacing. Row-by-row assignments are UNRESOLVED; neither OCR nearest-line alignment nor proportional spacing is reliable enough to publish named-job times.
- Repair codes in printed order: 1 crankcase; 2 crankshaft and/or bearings; 3 crankcase gasket/sealing; 4 crankshaft seals; 5 cylinder and/or piston; 6 ignition; 7 fuel supply/tank vent; 8 wheel guard; 9 carburetor; 10 arbor housing; 11 handlebar/buffers/handle frame; 12 recoil starter; 13 clutch; 14 V-belt pulley; 15 muffler; 16 air filter/filter cover; 17 stop switch.
- Numeric strip preserved independently, top to bottom (hours): 2.5, 2.5, 1.5, 1.2, 1.0, 0.5, 0.5, 0.3, 0.7, 0.6, 0.5, 0.5, 0.5, 0.4, 0.4, 0.3, 0.4, 0.5, 0.5, 0.5. No invented extra repair codes or silently dropped duplicate times. This is a retained source-layout contradiction, not a missing page.
- Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.
Source: TI 37/1995, p. 11 — TS 400 repair-time table: unmatched numeric strip retained.
No additional parts-table entry added.
Wrong number or missing part for the TS 400? Report a correction →