Stihl 4223 · Section M · 12 of 22 · 20 parts
Air filter
Fits TS 400.
Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.
Parts (20)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4223 121 6101 | Choke lever | 1 |
| 2 | 4221 129 0903 | Gasket | 1 |
| 3 | 4223 120 3402 | Filter base | 1 |
| 4 | 4223 124 4000 | Cap | 1 |
| 5 | 9416 868 6630 | Hollow rivet 6.5x0.5x6.8 | 6 |
| 6 | 4223 121 2400 | Flat spring | 1 |
| 7 | 9220 260 0700 | Hexagon nut M5 | 2 |
| 8 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 6 |
| 9 | not sold separately | Hose 3.1x5.7x94 mm, R3 not available as a separate item | 1 |
| 10 | 4223 140 1800 | Auxiliary filter | 1 |
| 11 | 4223 141 0300 | Air filter | 1 |
| 12 | 4223 140 2800 | Filter housing | 1 |
| 13 | 4223 149 0500 | Gasket | 1 |
| 14 | 4223 141 0600 | Prefilter | 1 |
| 15 | 4223 141 0500 | Filter cover | 1 |
| 16 | 4223 140 9300 | Twist lock | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 930 2803 | Hose 3.1x5.7 mm x 1 m, R3 not illustratedoption | 1 |
| — | 0712 923 8004 | Hose 3.1x5.7 mm x 10 m, R3 not illustratedoption | 1 |
| — | 4223 007 1010 | Air filter kit option | 1 |
| — | 4223 007 1050 | Set of gaskets | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · TS 400
TS 400 air filter: three stages and compensator connection
The compensator references clean-side pressure; cleaning remains necessary.
- Intake ports are placed in the least dusty area. Figure 338TI001 identifies high-volume FOAM PREFILTER (1), large-area MAIN FILTER (2) with vertical folds and described self-cleaning effect, and FLOCKED-FABRIC AUXILIARY FILTER (3) for fine dust. The central wing nut releases the cover for prefilter inspection and service. These are TI figure labels, not later IPL positions.
- The carburetor metering-chamber end-cover connector is linked by HOSE TO THE INTAKE MANIFOLD, equalizing pressure on the clean-air side of the filter and at the control diaphragm. Filter fouling lowers pressure at the venturi and outside of the control diaphragm; the diaphragm moves outward, partly closing the needle valve and reducing fuel supply.
- Source says this prevents progressive enrichment and eliminates further high-speed screw adjustment AS THE FILTER BECOMES SOILED. It is not permission to omit initial carburetor setting or diagnose all running faults as filter fouling. Claimed constant fuel proportion and delayed power loss extend service intervals; optimum performance returns after prefilter cleaning and/or main-filter replacement. No numeric cleaning interval is printed.
- Pressure diagram uses a separate numbering: 1 air filter, 2 carburetor, 3 cylinder, 4 fuel tank; Pi internal pressure, Pa external pressure, Pr pressure in metering chamber. These are not the filter-layer labels. No later HS-274E, WJ-108A, HS-279D or Japan HS-301B carburetor identity is established by this 1995 section.
- Historical TI guidance for the 1995 TS 400, type 4223, only. Later exact-model IPL sheets are navigation aids, not evidence that every later variant has the original configuration. No hardware operation was performed.
Source: TI 37/1995, p. 2 · TI 37/1995, p. 3 — TS 400 air filter: three stages and compensator connection.
No additional parts-table entry added.
Service note · TS 400
TS 400 fuel system: initial screw settings and 1:50 oil condition
H and L start approximately one turn open; carburetor test pressure is 0.8 bar.
- All-position diaphragm carburetor with integral fuel pump. H high-speed and L low-speed screws each APPROXIMATELY ONE TURN OPEN, starting from closed screws. These are source initial settings, not a complete final running adjustment procedure or permission to force seated screws. No carburetor manufacturer/model is printed.
- Carburetor excess-pressure leakage test 0.8 bar; no hold time or permissible pressure decay stated. Fuel tank 0.74 l (1.56 pt). Source specifies branded mid-grade gasoline (89 octane) and branded two-stroke oil; it does not identify the octane test method.
- Mixing ratio 1:50 is explicitly for STIHL TWO-STROKE ENGINE OIL 1:50. Do not silently generalize the ratio to every unspecified oil or rewrite historical fuel guidance as current approval.
- Filter material roster: foam prefilter, large PAPER main filter, and auxiliary filter of flocked PLASTIC FABRIC. This adds material detail to the mechanism description without inventing a maintenance interval.
- Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.
Source: TI 37/1995, p. 7 — TS 400 fuel system: initial screw settings and 1:50 oil condition.
No additional parts-table entry added.
Service note · TS 400
TS 400 tightening torques: starter, handles, filter and muffler
Identical screw sizes have different joint-specific torques.
- All values in Nm. Groove-headed IS-DG 4 x 14 starter cover: 1.8, with Loctite 242/243. Socket-head IS-DG 4 x 15 handle moulding/handle: 1.8; same size stop-linkage mount: 1.8. IS-DGM 5 x 20 handlebar/handlebar mount: 8.0 (DGM designation retained as printed); IS-DG 5 x 20 tank housing left/right: 7.5. M 5 nut filter base/carburetor: 3.5.
- Socket-head IS-M 5 x 16: tensioner cover/cast arm 4.5; handlebar/tank housing 8.0; air baffle/crankcase 4.5; muffler/crankcase 10.0; muffler/cylinder 10.0. Do not derive torque solely from thread size.
- Socket-head IS-M 5 x 20: cast arm/crankcase 10.0; filter base/tank housing 6.0; filter case/filter base 4.0 (the source misspells the last label Fitler). Thread/size descriptions are not ordering numbers. See the DG procedure note for thread re-engagement and adhesive removal.
- Historical TI guidance for the 1995 TS 400, type 4223. Later IPL sheets are exact-model navigation aids, not proof of identical later configuration or current tool availability. No hardware operation was performed.
Source: TI 37/1995, p. 7 · TI 37/1995, p. 8 — TS 400 tightening torques: starter, handles, filter and muffler.
No additional parts-table entry added.
Wrong number or missing part for the TS 400? Report a correction →