Stihl 4223 · Section N · 13 of 22 · 24 parts
Shroud
Fits TS 400.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (24)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4223 080 1604 | Shroud | 1 |
| 2 | 9416 868 6630 | Hollow rivet 6.5x0.5x6.8 | 4 |
| 3 | 4223 967 1500 | Model plate TS 400 | 1 |
| 4 | 4223 084 7400 | Grommet | 1 |
| 5 | 4223 431 8300 | Insert | 1 |
| 6 | 4223 123 7500 | Grommet Fitment / change note → | 1 |
| 7 | 4223 123 7501 | Grommet Fitment / change note → | 1 |
| 8 | 4223 182 1500 | Throttle rod | 1 |
| 9 | 4223 435 6000 | Support | 1 |
| 10 | 4223 435 1100 | Shutdown rod | 1 |
| 11 | 4223 435 2100 | Torsion spring | 1 |
| 12 | 9075 478 3015 | Pan head self-tapping screw IS-D4x15 | 2 |
| 13 | 4223 084 7100 | Cap | 1 |
| 14 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 4 |
| 15 | 4223 182 1000 | Throttle trigger | 1 |
| 16 | 9371 470 2640 | Cylindrical pin 5x24 | 1 |
| 17 | 4223 182 0800 | Lockout lever | 1 |
| 18 | 1117 182 4500 | Torsion spring | 1 |
| 19 | 4223 182 0900 | Switch shaft | 1 |
| 20 | 4223 182 4700 | Flat spring | 1 |
| 21 | 4223 791 0600 | Handle molding | 1 |
| 22 | 0000 967 3702 | Warning pictogram TS | 1 |
| 23 | 0000 967 3693 | Warning pictogram Filler cap | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4223 080 1605 | Shroud | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · TS 400
TS 400: Choke word added at cold-start position
Label identifies choke shutter closed; no shroud part number or serial is printed.
- The shroud will additionally carry the word “Choke” IN FUTURE to help avoid operator errors. Section2 explicitly identifies the indicated position as CHOKE SHUTTER CLOSED (COLD START). Figure 338TI007 KN shows the word beside the existing control pictograms.
- This is a marking change, not a changed lever mechanism, engine-running setting or evidence of a different starting procedure. No shroud part number, separate decal number, numeric changeover, retrofit requirement or old-shroud availability is provided. Do not copy section1 serial X 33 772 153 into this note.
- Historical TI 13/1996 evidence for TS 400, type 4223; no successor or additional market-specific variant applicability inferred. No hardware operation was performed; availability and performance rationale are historical statements, not current stock or a measured repair result.
Source: TI 13/1996, p. 2 — TS 400: Choke word added at cold-start position.
No additional parts-table entry added.
Conditional replacement · TS 400
TS 400: shroud supply and two-opening grommet
The shroud remains usable on old and new machines; contradictory grommet availability wording is retained.
- Historical TI04/1998 for TS 400, type 4223 only. Later 2012 IPL sheets are navigation/comparison, not evidence that their later versions equal the 1998 configuration. No extension to Japan-specific carburetors, other cut-off machines or saws. Historical factory availability is not current stock. No hardware operation was performed.
- The three-opening H/L/LA grommet 4223 123 7500 (drawing item 1) is replaced in the new installation by two-opening L/LA grommet 4223 123 7501 (drawing item 2), guiding the carburetor screwdriver. Drawing 338TI014 KN retains L above LA, with no H opening on the new version.
- The prose then says “The grommet is no longer available.” But table row 11 marks the original grommet with remark 3, which says it REMAINS AVAILABLE for older machines, and row 12 lists the new grommet. This is an unresolved internal availability conflict; do not silently choose one reading. The later IPL lists both grommets but cannot resolve what the 1998 prose intended.
- Throttle trigger, trigger interlock and choke lever are modified. The replacement shroud can still be used for old and new machines. To simplify replacement a complete shroud including all individual throttle-control parts is additionally offered; no individual trigger/interlock numbers or installation torque are given in this TI.
- Row 9 adds complete shroud 4223 080 1603, including item 10. Row 10 retains 4223 080 1600 on both sides and says including item 11, BUT remark 5 says only the MODIFIED VERSION WITHOUT GROMMET is factory-supplied. Preserve this qualification rather than promising that the inclusion heading guarantees a grommet.
- Introduction is continuous, not either printed carburetor/starter serial. Later IPL shrouds 4223 080 1604 and 4223 080 1605 do not silently replace the 1998 1600/1603 contents or establish identical equipment.
Source: TI 4/1998, p. 2 — Section 1.4 and summary rows 9–12, remark 5, grommet drawing.
Part numbers (4)
- 4223 080 1603 — Complete shroud including item 10 and throttle-control partsAdditional supply assembly · TS 400; only the version and conditions stated here
- 4223 080 1600 — Shroud; number unchangedModified supply without grommet · TS 400; only the version and conditions stated here
- 4223 123 7500 — Three-opening grommetOriginal; availability conflict · TS 400; only the version and conditions stated here
- 4223 123 7501 — Two-opening grommetNew version · TS 400; only the version and conditions stated here
Wrong number or missing part for the TS 400? Report a correction →