Stihl 4226 · Section B · 2 of 10 · 35 parts
Rewind starter, Ignition system
Fits HS 72, HS 74, HS 76.
Historical fitment & changes (8) — includes parts and conditions not shown on this drawing.
Parts (35)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4133 190 2002 | Carrier | 1 |
| 2 | 4133 195 7201 | Pawl | 1 |
| 3 | 0000 998 0612 | Torsion spring | 1 |
| 4 | 4226 190 0400 | Starter cover | 1 |
| 5 | 4137 190 1100 | Rope rotor with rewind spring Fitment / change note → | 1 |
| 6 | 0000 195 8200 | Starter rope Ø 3x800 mm Fitment / change note → | 1 |
| 7 | 9104 003 0960 | Self-tapping screw P5.5x12 | 1 |
| 8 | 4117 195 3400 | Starter grip | 1 |
| 9 | 4226 791 7200 | Sleeve | 3 |
| 10 | 4226 141 0301 | Prefilter | 1 |
| 11 | 4226 967 1500 | Model plate HS 72 | 1 |
| 11 | 4226 967 1501 | Model plate HS 74 | 1 |
| 11 | 4226 967 1502 | Model plate HS 76 | 1 |
| 12 | 9022 341 0980 | Spline screw IS-M5x16 | 5 |
| 13 | 4226 149 0600 | Muffler gasket | 1 |
| 14 | 4133 140 0606 | Muffler Fitment / change note → | 1 |
| 15 | 9022 341 0960 | Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 | 1 |
| 16 | 4227 149 0606 | Muffler gasket Fitment / change note → | 1 |
| 17 | 4133 145 1001 | Insert Fitment / change note → | 1 |
| 18 | 1113 141 9000 NLA | Screen | 1 |
| 19 | 4226 145 0601 | Cover plate Fitment / change note → | 1 |
| 20 | 9022 313 0660 | Spline screw IS-M4x12 | 4 |
| 21 | 4112 036 8600 | Woodruff key | 1 |
| 22 | 4133 400 1200 | Flywheel Fitment / change note → | 1 |
| 23 | 4133 400 1301 | Ignition module Fitment / change note → | 1 |
| 24 | not sold separately | Ignition lead 180 mm not available as a separate item | 1 |
| 25 | 0000 989 1012 | Grommet | 1 |
| 26 | 4133 405 8001 | Insulator | 1 |
| 27 | 9022 371 0710 | Spline screw IS-M4x20 | 2 |
| 28 | 4133 160 2020 | Clutch Fitment / change note → | 1 |
| 29 | 4133 162 7900 | Tension spring Fitment / change note → | 2 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4226 190 4005 | Rewind starter | 1 |
| — | 0000 930 2208 NLA | Starter rope Ø 3 mm x 30.5 m not illustratedoption | 1 |
| — | 0000 405 0600 NLA | Ignition lead 1 m not illustratedoption | 1 |
| — | 0000 930 2251 | Ignition lead 10 m not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · HS 72 / HS 74 / HS 76
HS 72 / HS 74 / HS 76: series 4226 replacement ignition assignment
4133 400 1301 with flywheel 4133 400 1200; 175 mm ignition lead.
- Printed series 4226. Use 4133 400 1301 with flywheel 4133 400 1200.
- Printed ignition-lead length: 175 mm (6 7/8 in). Preserve both printed units.
- TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
- Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
- Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
- Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
- Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.
Source: TI 1/1999, p. 1 · TI 1/1999, p. 3 — 1.1 general restrictions and 1.2.2 power-tool assignments.
Part numbers (2)
- 4133 400 1301 — Replacement ignition moduleAssigned component · HS 72 / HS 74 / HS 76, printed series 4226, listed combination only
- 4133 400 1200 — Assigned flywheelRequired pairing · HS 72 / HS 74 / HS 76, printed series 4226
Conditional replacement · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / KM 85 / FS 75 / FS 80 / FS 85 / BG 72 / BG 75 / FC 72 / FS 72 / FS 74 / FS 76 / HS 75 / HS 80 / HS 85 / HS 72 / HS 74 / HS 76
TI24/2002: three starter-rope stages and model scope
Keep the original, interim and final rope sizes separate; HS72/74/76 do not inherit the grip change.
- Original starter rope 4123 195 8200 is 0.105 in / 2.7 mm diameter and 31.5 in / 800 mm long. Interim rope 0000 195 8200 is 0.120 in / 3 mm diameter and the same 31.5 in / 800 mm length. Final rope 4137 195 8200 returns to 0.105 in / 2.7 mm diameter but increases length to 35.8 in / 910 mm. Do not confuse unchanged diameter with unchanged length.
- The interim rope is included in ElastoStart 0000 190 3400; the final rope is used in ElastoStart 0000 190 3403. Those grip associations describe the main starter branch; section 2.7 extends subsections 2.1, 2.3, 2.4 and 2.5 to HS 72, HS 74 and HS 76, but not subsection 2.2. No ElastoStart-grip replacement is authorized for those three models by this TI.
- Summary remarks distinguish earlier-to-interim from interim-to-new changes. Original rope 4123 195 8200 and interim rope 0000 195 8200 remain available for other models; their removal from this branch does not mean universal discontinuation. Section 2.6 states the new starter parts are fully interchangeable with previous machine versions within the applicable section 2 model scope.
- These are section 2 starter changes, not section 1 control-handle/throttle-cable retrofit permission. Main models come from the heading; additional models follow section 2.7. The old series 4112 FS 80 is not bound merely because its name matches. Shared IPL sheets do not extend applicability to unnamed variants. Introduction is in progress without a starter serial cutoff; factory availability is historical, not current stock. No physical interchange test was performed.
Source: TI 24/2002, p. 1 · TI 24/2002, p. 8 · TI 24/2002, p. 9 — Heading model scope; section2 starter diagram, subsections2.1–2.8 and ten-row summary/six remarks.
Part numbers (3)
- 4123 195 8200 — Starter rope 2.7 x 800 mmOriginal; retained for other models · Named section 2 models only; see conditions
- 0000 195 8200 — Starter rope 3 x 800 mmInterim; retained for other models · Named section 2 models only; see conditions
- 4137 195 8200 — Starter rope 2.7 x 910 mmFinal version · Named section 2 models only; see conditions
Conditional replacement · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / KM 85 / FS 75 / FS 80 / FS 85 / BG 72 / BG 75 / FC 72 / FS 72 / FS 74 / FS 76 / HS 75 / HS 80 / HS 85 / HS 72 / HS 74 / HS 76
TI24/2002: rope rotor and spring supplied as an assembly
Preserve the interim-rotor availability conflict; new rotor and spring are not separate spares.
- Original rope rotor 4133 195 0400 was replaced by interim rotor 4133 195 0470. The TI says the interim rotor is no longer available separately and the rewind spring 4133 195 1600 is likewise supplied only as part of rope rotor with rewind spring 4137 190 1100. The new assembly contains the rotor and spring; no independent new numbers are given for either component.
- The starter drawing labels rope (1), ElastoStart grip (2), rotor (3), spring (4), and rotor/spring assembly (5). These are not the summary-table row numbers: assembly 4137 190 1100 is summary item 8, with its spring and rotor as items 9 and 10.
- Preserved source tension: prose and summary remark 4 say the interim rotor is no longer available from the factory, while summary item 10 (previous rotor 4133 195 0470) carries remark 3 permitting previous stock until exhausted. Spring item 9 also carries the stock remark despite prose saying it is no longer separate. New separate items are explicitly unavailable under remark 6; use assembly item 8. Do not silently collapse these phase/stock statements into a current availability promise.
- Section 2.7 explicitly extends subsections 2.3–2.5, as well as rope subsection 2.1, to HS 72, HS 74 and HS 76. The broader group receives all starter modifications. Section 2.6 states full interchangeability with previous versions within this starter scope, not a control-handle equivalence rule. All other parts are stated unchanged.
- These are section 2 starter changes, not section 1 control-handle/throttle-cable retrofit permission. Main models come from the heading; additional models follow section 2.7. The old series 4112 FS 80 is not bound merely because its name matches. Shared IPL sheets do not extend applicability to unnamed variants. Introduction is in progress without a starter serial cutoff; factory availability is historical, not current stock. No physical interchange test was performed.
Source: TI 24/2002, p. 1 · TI 24/2002, p. 8 · TI 24/2002, p. 9 — Heading model scope; section2 starter diagram, subsections2.1–2.8 and ten-row summary/six remarks.
Part numbers (4)
- 4133 195 0400 — Rope rotorOriginal; stocks-only phase · Named section 2 models only; see conditions
- 4133 195 0470 — Rope rotorInterim; conflicting separate-stock statements · Named section 2 models only; see conditions
- 4133 195 1600 — Rewind springPrevious separate part; stock/assembly statements retained · Named section 2 models only; see conditions
- 4137 190 1100 — Rope rotor with rewind springNew assembly; includes both components · Named section 2 models only; see conditions
Service note · HS 72 / HS 74 / HS 76
HS 72 / 74 / 76: asymmetric muffler holes and mandatory outlet orientation
New slotted companion parts fit both muffler versions; original parts need modification with the new muffler.
- Top-left muffler mounting hole moves about 2.5 mm (0.10 in) LEFT to enforce cover-plate orientation. New exhaust gasket, insert and cover plate have a slotted top-left mounting point and fit original and new parts. With new muffler replacing original, either MODIFY original gasket/insert/cover or install new versions; no detailed machining method is supplied.
- WARNING for assembly of ORIGINAL muffler, insert and cover: cover outlet MUST POINT TOWARD CUTTER BAR; short tube in insert MUST POINT TOWARD FAN HOUSING. Wrong orientation can damage the fuel tank with hot exhaust gases and cause FIRE AND BURNS. Do not omit either direction or interpret cross-version compatibility as arbitrary orientation.
- Complete muffler includes items 1–4; gasket set includes exhaust gasket item 2. Only new complete muffler and gasket set factory-available; old gasket/insert/cover only while stocks last. Introduction IN PROGRESS, no serial. Cover MOQ 5 is not five fitted plates.
- Historical TI 25/1994 guidance only. No successor or unlisted model applicability inferred. Factory supply and warranty statements are historical, not current availability or entitlement. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.
Source: TI 25/1994, p. 1 · TI 25/1994, p. 2 — HS 72 / 74 / 76: asymmetric muffler holes and mandatory outlet orientation.
Part numbers (12)
- 4226 140 0600 — Complete mufflerold · HS 72 / 74 / 76: asymmetric muffler holes and mandatory outlet orientation
- 4226 140 0601 — Complete mufflernew; items1–4 · HS 72 / 74 / 76: asymmetric muffler holes and mandatory outlet orientation
- 4133 140 0605 — Muffler bodyold · HS 72 / 74 / 76: asymmetric muffler holes and mandatory outlet orientation
- 4133 140 0606 — Muffler bodynew · HS 72 / 74 / 76: asymmetric muffler holes and mandatory outlet orientation
- 4227 149 0605 — Exhaust gasketold; stocks only · HS 72 / 74 / 76: asymmetric muffler holes and mandatory outlet orientation
- 4227 149 0606 — Exhaust gasketnew slotted · HS 72 / 74 / 76: asymmetric muffler holes and mandatory outlet orientation
- 4133 145 1000 — Insertold; stocks only · HS 72 / 74 / 76: asymmetric muffler holes and mandatory outlet orientation
- 4133 145 1001 — Insertnew slotted · HS 72 / 74 / 76: asymmetric muffler holes and mandatory outlet orientation
- 4226 145 0600 — Cover plateold; stocks only · HS 72 / 74 / 76: asymmetric muffler holes and mandatory outlet orientation
- 4226 145 0601 — Cover platenew slotted · HS 72 / 74 / 76: asymmetric muffler holes and mandatory outlet orientation
- 4226 007 1050 — Gasket setold unavailable · HS 72 / 74 / 76: asymmetric muffler holes and mandatory outlet orientation
- 4226 007 1051 — Gasket setnew including exhaust gasket · HS 72 / 74 / 76: asymmetric muffler holes and mandatory outlet orientation
Service note · HS 72 / HS 74 / HS 76
HS 72 / 74 / 76: clutch carrier and shoes must not be mixed
Complete-assembly exchangeability does not permit individual old/new component interchange.
- Modified carrier and shoes optimize performance; ORIGINAL AND NEW COMPONENTS ARE NOT INTERCHANGEABLE. Only complete clutch assembly supplied for easy replacement. Assembly 4133 160 2000 retains number across carrier revision. Old clutch prose shows ONE DOT; table also permits unmarked (--,1); modified clutch has TWO DOTS ON EACH SHOE.
- Installed modified carrier has narrower square head A: old 14 mm (9/16 in), new 10 mm (13/32 in). B denotes dot marking. These are CLUTCH HEAD sizes, not wrench SW. Modified clutch requires wrench 4133 893 1301. Introduction IN PROGRESS; unmodified assembly only while stocks last.
- Historical TI 25/1994 guidance only. No successor or unlisted model applicability inferred. Factory supply and warranty statements are historical, not current availability or entitlement. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.
Source: TI 25/1994, p. 6 · TI 25/1994, p. 7 · TI 25/1994, p. 8 — HS 72 / 74 / 76: clutch carrier and shoes must not be mixed.
Part numbers (2)
- 4133 160 2000 — Clutch assemblysame number across carrier revision · HS 72 / 74 / 76: clutch carrier and shoes must not be mixed
- 4133 893 1301 — Clutch wrenchrequired for modified carrier · HS 72 / 74 / 76: clutch carrier and shoes must not be mixed
Service note · HS 72 / HS 74 / HS 76
HS 72 / 74 / 76: new clutch wrench fits both versions
Old wrench fits original clutch only; SW and clutch-head dimensions are different datums.
- Wrench 4133 893 1301 replaces 4133 893 1300. NEW wrench fits ALL original/new versions; OLD wrench fits ONLY ORIGINAL clutch. Table SW across-flats: old 13 mm (33/64 in), new 17 mm (43/64 in). Clutch-head A separately old 14 mm (9/16 in), new 10 mm (13/32 in). Do not swap or equate these datums.
- Illustrations 3/4 identify old/new wrench; installed carrier A/B diagram distinguishes head and dots. Introduction IN PROGRESS; old wrench available only while factory stocks last. No torque inferred.
- Historical TI 25/1994 guidance only. No successor or unlisted model applicability inferred. Factory supply and warranty statements are historical, not current availability or entitlement. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.
Source: TI 25/1994, p. 7 · TI 25/1994, p. 8 — HS 72 / 74 / 76: new clutch wrench fits both versions.
Part numbers (2)
- 4133 893 1300 — Clutch wrenchold; original clutch only · HS 72 / 74 / 76: new clutch wrench fits both versions
- 4133 893 1301 — Clutch wrenchnew; both clutch versions · HS 72 / 74 / 76: new clutch wrench fits both versions
Service note · HS 72 / HS 74 / HS 76
HS 72 / 74 / 76: lined replacement clutch differs from production clutch
Replacement assembly includes two shoes and two springs; shoes are not separate spares.
- Clutch 4133 160 2020 with LINED shoes is supplied as SPARE to standardize with FS 72/74/76 parts; UNLINED shoes continue in PRODUCTION. This cross-reference does not extend this TI to FS models. Original spare assembly is 4133 160 2000.
- New assembly includes TWO shoes (item 5, not separately supplied; -*- is no part number) and TWO springs 4133 162 7900 (item 6). Modified spring hooks fit BOTH original/new shoes and have already been standard for some time; spring number unchanged. Table introduction says IN PROGRESS; old assembly and unmodified spring only while stocks last. Spring compatibility does not relax carrier/shoe mixing prohibition.
- Historical TI 25/1994 guidance only. No successor or unlisted model applicability inferred. Factory supply and warranty statements are historical, not current availability or entitlement. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.
Source: TI 25/1994, p. 7 · TI 25/1994, p. 8 — HS 72 / 74 / 76: lined replacement clutch differs from production clutch.
Part numbers (3)
- 4133 160 2000 — Clutch assemblyoriginal spare · HS 72 / 74 / 76: lined replacement clutch differs from production clutch
- 4133 160 2020 — Lined clutch assemblyreplacement spare only · HS 72 / 74 / 76: lined replacement clutch differs from production clutch
- 4133 162 7900 — Clutch spring2 fitted; modified hooks, unchanged number · HS 72 / 74 / 76: lined replacement clutch differs from production clutch
Service note · BG 75 / FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75 / HS 75 / HS 80 / HS 85 / BG 72 / FC 72 / FS 48 / FS 52 / FS 56 / FS 62 / FS 66 / FS 72 / FS 74 / FS 76 / HS 72 / HS 74 / HS 76
ElastoStart replacement rope: original-number conflict retained
New 0000 195 8200 is3.0×800 mm; prose and table disagree on the original.
continuously — Continuous introduction; no numeric boundary supplied for this particular change.
- Section 3 prose prints ORIGINAL 4123 190 4000 (2.7×900 mm), replaced for some time by ELASTOSTART 0000 195 8200 (3.0×800 mm). The summary instead prints ORIGINAL 4123 195 8200. Both are confirmed on the original scan: retain the UNRESOLVED NUMBER CONFLICT, not an OCR correction, proven equivalence or two-step supersession.
- In addition to cover models, the source explicitly extends this change to BG 72, FC 72, FS 48/52/56/62/66/72/74/76 and HS 72/74/76. These are the historical configurations: not the later type 4144 FS 56 or type 4112 FS 80.
- Modification introduced CONTINUOUSLY; summary remark says ORIGINAL NO LONGER AVAILABLE FROM FACTORY. No machine-number cutoff, handle assembly replacement, knot procedure or permission to shorten either rope to an unprinted length is given. Catalog associations expose the historical note without rewriting their rope rows or choosing which conflicting original is correct.
- Historical TI 41/1997 evidence for the named models and configurations only; not present stock, a universal serial-to-model registry or verified physical interchange. No hardware operation was performed.
Source: TI 41/1997, p. 5 — Entire section 3 prose, extended model list, summary and availability remark.
Part numbers (3)
- 4123 190 4000 — Original rope number printed in prose;2.7×900 mmConflicts with summary original · Only the named TI 41/1997 configurations and conditions
- 4123 195 8200 — Original rope number printed in summaryConflicts with prose original · Only the named TI 41/1997 configurations and conditions
- 0000 195 8200 — ElastoStart rope;3.0×800 mmReplacement · Only the named TI 41/1997 configurations and conditions
Wrong number or missing part for the HS 72, HS 74, HS 76? Report a correction →