← HS 72, HS 74, HS 76 · HS 75, HS 80, HS 85

Stihl 4226 · Section A · 1 of 10 · 23 parts

Crankcase, Cylinder

Fits HS 72, HS 74, HS 76.

Parts diagrams →

Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121213141415161718192334456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (23)

PosPart numberDescriptionQty
1 4133 020 2801 Crankcase, starter side Fitment / change note → 1
2 9380 620 2570 Roll pin 5x12 2
3 9503 003 0242 Grooved ball bearing 6201 2
4 9640 003 1195 Oil seal 12x22x5 2
5 4133 020 2601 Crankcase, fan side Fitment / change note → 1
6 4133 030 0400 Crankshaft 1
7 9022 341 1050 Spline screw IS-M5x25 3
8 4133 022 0501 Cylinder Ø 33mm 1
9 4133 034 0500 Piston Ø 33 mm 1
10 4133 034 3000 Piston ring Ø 33x1.5 mm 2
11 4112 034 1500 Piston pin 1
12 9463 650 0805 Snap ring 8x0.7 2
13 9512 004 1820 Needle cage 8x11x10 1
14 4133 036 8901 Thrust washer 2
15 4133 029 2300 Cylinder gasket 1
16 9022 371 1020 Spline screw IS-M5x20 Fitment / change note → → replaced by 9022 371 1050 TI 30/2004 2
17 0000 400 7000 Spark plug NGK BPMR7A 1
17 1110 400 7005 Spark plug Bosch WSR 6 F 1
18 0000 998 0606 Torsion spring 1
19 1106 405 1000 Spark plug boot → replaced by 1128 405 1000, 1128 405 1000 TI 30/1995 1
Not numbered on the diagram — assemblies, kits and options
— 4133 020 1201 Cylinder with piston Ø 33 mm Fitment / change note → 1
— 4133 030 2000 Piston Ø 33 mm 1
— 0783 830 2000 Tube of sealant Dirko HT red not illustrated 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · HS 72 / HS 74 / HS 76

HS 72 / 74 / 76: grooved crankcase ledges retain interchangeability

Both halves change numbers; old-stock qualification is retained.

  • Each new crankcase half has integral ledge with groove, shown by arrows; change follows brushcutter engineering updates without adding brushcutter model applicability. Original and new halves are explicitly INTERCHANGEABLE. Fan side 4133 020 2600→4133 020 2601; starter side 4133 020 2800→4133 020 2801.
  • Prose says only new replacement parts will be available; table qualifies old versions as supplied UNTIL STOCKS EXHAUSTED. Both supply statements retained, no silent immediate-discontinuation inference. Introduction IN PROGRESS; no serial.
  • Historical TI 25/1994 guidance only. No successor or unlisted model applicability inferred. Factory supply and warranty statements are historical, not current availability or entitlement. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 25/1994, p. 5 — HS 72 / 74 / 76: grooved crankcase ledges retain interchangeability.

Part numbers (4)
  • 4133 020 2600 — Fan-side crankcaseold · HS 72 / 74 / 76: grooved crankcase ledges retain interchangeability
  • 4133 020 2601 — Fan-side crankcasenew · HS 72 / 74 / 76: grooved crankcase ledges retain interchangeability
  • 4133 020 2800 — Starter-side crankcaseold · HS 72 / 74 / 76: grooved crankcase ledges retain interchangeability
  • 4133 020 2801 — Starter-side crankcasenew · HS 72 / 74 / 76: grooved crankcase ledges retain interchangeability

Service note · HS 72 / HS 74 / HS 76

HS 72 / 74 / 76: uprated engine requires all new parts

From X 30 314 341; approximate 15% increase to 0.8 kW / 1.1 bhp is not a single-part retrofit.

X 30 314 341 — Printed introduction of the uprated HS 72/74/76 engine; not a universal series or successor cutoff.

  • FROM X 30 314 341 engine output rises approximately 15% to 0.8 kW (1.1 bhp), through different port timing, higher compression ratio, enlarged inlet port, modified transfer ports, and modified gasket and spacer flange. No numerical port timing or compression ratio is supplied.
  • Factory supply describes new cylinder, gasket and spacer flange as universal replacement parts within these named models. That wording DOES NOT remove the assembly conditions: ONLY NEW versions may repair NEW machine versions, otherwise loss of power and running problems may occur. Increasing an OLD machine to approximately 0.8 kW is possible ONLY IF ALL NEW PARTS ARE INSTALLED, with required screws, plugs and washers.
  • Cylinder mounting requires M5 x 20 screws at 10 Nm (7.5 lbf.ft); the intake assembly must satisfy the separate flange instructions. Neither the performance claim nor universal-replacement wording authorizes mixing old parts into a new engine or omitting companion hardware. Footer January 1, 1995; TI25.94 is a prior-bulletin pointer, not a missing prerequisite.
  • Historical TI 02/1995 guidance only. Factory availability and performance claims are historical, not current stock or measured results. MOQ means order quantity, not installed quantity. No unlisted-model applicability inferred. No hardware operation was performed.

Source: TI 2/1995, p. 1 · TI 2/1995, p. 2 · TI 2/1995, p. 3 — HS 72 / 74 / 76: uprated engine requires all new parts.

No additional parts-table entry added.

Service note · HS 72 / HS 74 / HS 76

HS 72 / 74 / 76: new cylinder must use longer mounting screws

M5 x 20 replaces M5 x 16 for the new cylinder; old shorter screws must not be reused.

X 30 314 341 — Printed introduction of the uprated HS 72/74/76 engine; not a universal series or successor cutoff.

  • New cylinder has an approximately 3 mm (0.12 in) higher base flange and larger inlet opening. Illustration 356TI001 shows original/new base dimensions 7/10 and inlet widths 15/19, with inlet heights 9/10.5 (printed 10,5). These cylinder dimensions are distinct from the gasket window widths 16/19 mm on page 2; do not substitute gasket width for cylinder width.
  • New cylinder MUST use TWO M5 x 20 screws 9022 371 1020, including when installed on older machines. DO NOT USE original M5 x 16 screws 9022 341 0980. Tightening torque is 10 Nm (7.5 lbf.ft). The new screw MOQ H 10 is not ten installed screws; old screws remain spare parts for their applicable uses, not permission to fit them to the new cylinder.
  • Cylinder with piston 4133 020 1200 becomes 4133 020 1201, including table items 1 and 2. Cylinder 4133 022 0500 becomes printed 4133 020 1250 (item 1), including new screws item 2. Both original cylinder versions are no longer factory-available; all other parts remain as before. MOQ H 1 for each cylinder offering.
  • Retained 2012 HS 72/74/76 sheet A lists separate cylinder 4133 022 0501, unlike the TI’s 4133 020 1250, while the complete-cylinder number agrees. Keep both source identifiers; no unprovided supersession or typographic correction is inferred. This historical 1995 screw instruction does not flatten later version-specific changes.
  • Historical TI 02/1995 guidance only. Factory availability and performance claims are historical, not current stock or measured results. MOQ means order quantity, not installed quantity. No unlisted-model applicability inferred. No hardware operation was performed.

Source: TI 2/1995, p. 1 · TI 2/1995, p. 2 · TI 2/1995, p. 3 — HS 72 / 74 / 76: new cylinder must use longer mounting screws.

Part numbers (6)
  • 4133 020 1200 — Cylinder with pistonoriginal; unavailable · HS 72 / 74 / 76: new cylinder must use longer mounting screws
  • 4133 020 1201 — Cylinder with pistonnew; includes items 1 and 2 · HS 72 / 74 / 76: new cylinder must use longer mounting screws
  • 4133 022 0500 — Cylinderoriginal; unavailable · HS 72 / 74 / 76: new cylinder must use longer mounting screws
  • 4133 020 1250 — Cylinderprinted new number; includes item 2 · HS 72 / 74 / 76: new cylinder must use longer mounting screws
  • 9022 341 0980 — Spline screw IS-M5 x16two old; prohibited with new cylinder · HS 72 / 74 / 76: new cylinder must use longer mounting screws
  • 9022 371 1020 — Spline screw IS-M5 x20two required; 10 Nm; MOQ10 · HS 72 / 74 / 76: new cylinder must use longer mounting screws

Wrong number or missing part for the HS 72, HS 74, HS 76? Report a correction →