← HS 72, HS 74, HS 76 · HS 75, HS 80, HS 85

Stihl 4226 · Section F · 6 of 10 · 35 parts

Gear housing, Cutter bar 420mm / 17''

Fits HS 72, HS 74, HS 76.

Parts diagrams →

Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141415161717181819220212122222323242525252627282933303132333445789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (35)

PosPart numberDescriptionQty
1 4226 160 2900 Clutch drum Fitment / change note → 1
2 4226 640 0500 Gear housing Fitment / change note → 1
3 4226 642 9700 Bushing Fitment / change note → 2
4 9503 003 5290 Grooved ball bearing 6002-2RS Fitment / change note → 1
5 9456 621 3600 Circlip 32x1.2 Fitment / change note → 1
7 9371 470 2580 Cylindrical pin 5x14 2
8 9455 621 1380 Circlip 14x1 Fitment / change note → 1
9 4226 642 9800 Eccentric bush 1
10 9022 341 1050 Spline screw IS-M5x25 1
11 4226 162 5001 Lever 1
12 9381 651 1701 Cylindrical pin 3x16 1
13 4226 162 5400 Brake band 1
14 4226 162 8900 Washer 2
15 0000 997 1600 Compression spring 1
16 9022 313 0680 Spline screw IS-M4x16 1
17 4230 642 4800 Thrust plate Fitment / change note → 2
18 4230 642 6501 Connecting rod 2
19 4226 640 7500 Spur gear Fitment / change note → 1
20 4226 792 9101 Cutter guard 1
21 4226 641 4602 Guide 420 mm / 17'' 2
22 4226 710 6059 Blade 420 mm 1
23 4226 713 6600 Pin 2
24 4226 713 1702 Flat spring 420 mm 1
25 9022 341 0980 Spline screw IS-M5x16 Fitment / change note → 6
26 4226 648 6700 Slider 6
27 9220 260 0701 Hexagon nut M5 Fitment / change note → 3
28 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 2
29 4226 790 9103 Blade guard 420 mm / 17'' 1
30 4226 649 0301 Gasket 1
31 4226 649 0300 Gasket Fitment / change note → 1
32 4226 640 5800 Gearbox cover Fitment / change note → 1
33 4226 641 6500 Screw plug Fitment / change note → 1
34 9022 313 0680 Spline screw IS-M4x16 6
Not numbered on the diagram — assemblies, kits and options
— 4226 710 5931 Cutter bar assy. 420 mm Fitment / change note → 1
— 0781 120 1109 Gear lubricant 80 g not illustratedoption 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · HS 72 / HS 74 / HS 76

HS 72 / 74 / 76: cutter locknut property class matched to screw

New M 5 locknut replaces old nut on all cutter-bar versions.

  • M5 locknut 9220 260 0701 replaces 9216 263 0700 on ALL cutter-bar versions of the named models. New property class matches IS-M5 x 16 screw 9022 341 0980 for reliability; numeric grade and torque not supplied. Old locknut remains supplied for OTHER MODELS. Introduction IN PROGRESS, no serial.
  • Historical TI 25/1994 guidance only. No successor or unlisted model applicability inferred. Factory supply and warranty statements are historical, not current availability or entitlement. MOQ columns are order quantities, not fitting quantities. No physical interchange test was performed.

Source: TI 25/1994, p. 5 — HS 72 / 74 / 76: cutter locknut property class matched to screw.

Part numbers (3)
  • 9216 263 0700 — M5 locknutold; other models · HS 72 / 74 / 76: cutter locknut property class matched to screw
  • 9220 260 0701 — M5 locknutnew matched property class · HS 72 / 74 / 76: cutter locknut property class matched to screw
  • 9022 341 0980 — IS-M5 x16 screwmatching screw · HS 72 / 74 / 76: cutter locknut property class matched to screw

Service note · HS 72 / HS 74 / HS 76 / HS 75 / HS 80 / HS 85

HS 72–85: matched gearbox drive changes from 7.1 to 5.6

57/8 teeth becomes 56/10; no mixed old/new gearbox parts.

X 36 360 021 — Gearbox change only; not all blade/fuel-system modifications.

  • From X 36 360 021 the printed gear ratio changes from 7.1 to 5.6 to increase blade speed. Original and new gearbox parts must NOT be used together in ANY combination. This is not permission to retrofit an individual new gear into the old housing.
  • Figures 366TI005/008/006/007/010/009/011/012 KN identify 1 as old and 2 as new: changed housing, bushing versus needle sleeve, cover and gasket outlines, spur gear, clutch drum, connecting rod and thrust plate. No dimensions are inferred from drawing scale.
  • Spur gear: old Z=57, new Z=56. Clutch drum: old Z=8, new Z=10. Table lists TWO connecting rods and TWO thrust plates; rod original prefix is 4206, not silently corrected to 4226.
  • Original drum, gear, rods and circlip remain spares for older models (remark 1). Original thrust plate supplied only while factory stocks last (remark 2).
  • Historical TI04/1997 evidence for HS 72, HS 74, HS 76, HS 75, HS 80 and HS 85, type 4226; the named blade length/carburetor/version remains a restriction, not every variant on every model. Factory-supply remarks describe 1997, not current availability. No hardware operation was performed.

Source: TI 4/1997, p. 1 · TI 4/1997, p. 2 · TI 4/1997, p. 3 — HS 72–85: matched gearbox drive changes from 7.1 to 5.6.

Part numbers (10)
  • 4226 160 2900 — Original clutch drumoriginal version · TI04/1997 exact named HS models and version restrictions
  • 4226 160 2901 — New clutch drumnew version · TI04/1997 exact named HS models and version restrictions
  • 4226 640 7500 — Original spur gearoriginal version · TI04/1997 exact named HS models and version restrictions
  • 4226 640 7504 — New spur gearnew version · TI04/1997 exact named HS models and version restrictions
  • 4206 642 6500 — Original connecting rod (2x)original version · TI04/1997 exact named HS models and version restrictions
  • 4226 642 6501 — New connecting rod (2x)new version · TI04/1997 exact named HS models and version restrictions
  • 4211 642 4800 — Original thrust plate (2x)original version · TI04/1997 exact named HS models and version restrictions
  • 4230 642 4800 — New thrust plate (2x)new version · TI04/1997 exact named HS models and version restrictions
  • 9455 621 1380 — Original circlip, item 11original version · TI04/1997 exact named HS models and version restrictions
  • 9455 621 1670 — New circlip, item 11new version · TI04/1997 exact named HS models and version restrictions

Service note · HS 72 / HS 74 / HS 76 / HS 75 / HS 80 / HS 85

HS 72–85: housing bearing and needle-sleeve contents

Housing includes items 2–6; new-only sleeve and roll pin retained.

X 36 360 021 — Matched gearbox housing change.

  • From X 36 360 021 the printed gear ratio changes from 7.1 to 5.6 to increase blade speed. Original and new gearbox parts must NOT be used together in ANY combination. This is not permission to retrofit an individual new gear into the old housing.
  • Figures 366TI005/008/006/007/010/009/011/012 KN identify 1 as old and 2 as new: changed housing, bushing versus needle sleeve, cover and gasket outlines, spur gear, clutch drum, connecting rod and thrust plate. No dimensions are inferred from drawing scale.
  • Housing 4226 640 0500 → 4226 640 0501 includes table items 2–6: changed ball bearing and circlip; original bushing has no new counterpart; new needle sleeve and 6 x 12 roll pin have no original counterparts. A dash is not a zero quantity or a missing transcription.
  • Original housing, bearing, bushing and item-4 circlip remain spares for older models. This does not relax the no-mixing rule. No later housing number is declared equivalent.
  • Historical TI04/1997 evidence for HS 72, HS 74, HS 76, HS 75, HS 80 and HS 85, type 4226; the named blade length/carburetor/version remains a restriction, not every variant on every model. Factory-supply remarks describe 1997, not current availability. No hardware operation was performed.

Source: TI 4/1997, p. 1 · TI 4/1997, p. 2 · TI 4/1997, p. 3 — HS 72–85: housing bearing and needle-sleeve contents.

Part numbers (9)
  • 4226 640 0500 — Original gearbox housingoriginal version · TI04/1997 exact named HS models and version restrictions
  • 4226 640 0501 — New gearbox housingnew version · TI04/1997 exact named HS models and version restrictions
  • 9503 003 5290 — Original ball bearingoriginal version · TI04/1997 exact named HS models and version restrictions
  • 9503 003 5382 — New ball bearingnew version · TI04/1997 exact named HS models and version restrictions
  • 4226 642 9700 — Original bushing, item 3Historical listed item · TI04/1997 exact named HS models and version restrictions
  • 9456 621 3600 — Original circlip, item 4original version · TI04/1997 exact named HS models and version restrictions
  • 9456 621 3860 — New circlip, item 4new version · TI04/1997 exact named HS models and version restrictions
  • 9513 003 0912 — New-only needle sleeve, item 5Historical listed item · TI04/1997 exact named HS models and version restrictions
  • 9381 003 2070 — New-only roll pin 6 x 12, item 6Historical listed item · TI04/1997 exact named HS models and version restrictions

Service note · HS 72 / HS 74 / HS 76 / HS 75 / HS 80 / HS 85

HS 72–85: cover includes its matching gasket

Old and new covers remain separate matched sets.

X 36 360 021 — Matched cover/gasket change.

  • From X 36 360 021 the printed gear ratio changes from 7.1 to 5.6 to increase blade speed. Original and new gearbox parts must NOT be used together in ANY combination. This is not permission to retrofit an individual new gear into the old housing.
  • Figures 366TI005/008/006/007/010/009/011/012 KN identify 1 as old and 2 as new: changed housing, bushing versus needle sleeve, cover and gasket outlines, spur gear, clutch drum, connecting rod and thrust plate. No dimensions are inferred from drawing scale.
  • Cover 4226 640 5800 → 4226 640 5850 includes items 13–15: changed screw plug, original-only bushing and new-only needle sleeve. Original cover/bushing remain spares for older models; original screw plug supplied while stocks last.
  • Gasket 4226 649 0300 → 4226 649 0302: each version will be supplied with its respective housing cover (remark 3). Do not mix gaskets/covers or interpret the two cover assemblies as interchangeable.
  • Historical TI04/1997 evidence for HS 72, HS 74, HS 76, HS 75, HS 80 and HS 85, type 4226; the named blade length/carburetor/version remains a restriction, not every variant on every model. Factory-supply remarks describe 1997, not current availability. No hardware operation was performed.

Source: TI 4/1997, p. 1 · TI 4/1997, p. 2 · TI 4/1997, p. 3 — HS 72–85: cover includes its matching gasket.

Part numbers (8)
  • 4226 640 5800 — Original gearbox housing coveroriginal version · TI04/1997 exact named HS models and version restrictions
  • 4226 640 5850 — New gearbox housing covernew version · TI04/1997 exact named HS models and version restrictions
  • 4117 713 6501 — Original screw plugoriginal version · TI04/1997 exact named HS models and version restrictions
  • 4226 641 6500 — New screw plugnew version · TI04/1997 exact named HS models and version restrictions
  • 4226 642 9700 — Original cover bushing, item 14Historical listed item · TI04/1997 exact named HS models and version restrictions
  • 9513 003 0912 — New cover needle sleeve, item 15Historical listed item · TI04/1997 exact named HS models and version restrictions
  • 4226 649 0300 — Original gasketoriginal version · TI04/1997 exact named HS models and version restrictions
  • 4226 649 0302 — New gasketnew version · TI04/1997 exact named HS models and version restrictions

Service note · HS 72 / HS 74 / HS 76 / HS 75 / HS 80 / HS 85

HS 72–85: 420 DS (16 in) longer-slot blade assembly

Check first slot: old 28 mm, new 31 mm; old blades forbidden on new gearbox.

  • Figure 366TI014 KN measures the FIRST SLOT: old 28 mm (1.10 in), new 31 mm (1.22 in). Check this slot before fitting individual blades. ORIGINAL-TYPE BLADES MUST NOT be used with the NEW gearbox. New assemblies should also be used for older machines (remark 2); this is not authorization to mix gearbox parts.
  • Table item 1 assembly includes the listed blade. All other parts remain as before. Every listed original assembly/blade is supplied only while factory stocks last (remark 1).
  • TI length labels are retained exactly; later IPL inch labels and later blade revisions do not silently replace them. Existing catalog rows, notes, positions and later serial restrictions remain unchanged.
  • X 36 209 590 applies ONLY to item 10, the 700 ES assembly. It is not a universal blade or gearbox cutoff.
  • Historical TI04/1997 evidence for HS 72, HS 74, HS 76, HS 75, HS 80 and HS 85, type 4226; the named blade length/carburetor/version remains a restriction, not every variant on every model. Factory-supply remarks describe 1997, not current availability. No hardware operation was performed.

Source: TI 4/1997, p. 1 · TI 4/1997, p. 4 — HS 72–85: 420 DS (16 in) longer-slot blade assembly.

Part numbers (4)
  • 4226 710 5930 — Original cutting blade assembly 420 DS (16 in)original version · TI04/1997 exact named HS models and version restrictions
  • 4226 710 5931 — New cutting blade assembly 420 DS (16 in)new version · TI04/1997 exact named HS models and version restrictions
  • 4226 710 6006 — Original 420 DS (16 in) bladeoriginal version · TI04/1997 exact named HS models and version restrictions
  • 4226 710 6026 — New 420 DS (16 in) bladenew version · TI04/1997 exact named HS models and version restrictions

Wrong number or missing part for the HS 72, HS 74, HS 76? Report a correction →