Stihl 4227 · Section A · 1 of 8 · 19 parts
Crankcase, Cylinder
Fits BG 75.
Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.
Parts (19)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4137 020 2800 | Crankcase, starter side | 1 |
| 2 | 0000 988 8600 | Sleeve | 2 |
| 3 | 9503 003 0242 | Grooved ball bearing 6201 | 2 |
| 4 | 9640 003 1195 | Oil seal 12x22x5 | 2 |
| 5 | 4137 020 2600 | Crankcase, fan side | 1 |
| 6 | 4137 030 0401 | Crankshaft | 1 |
| 7 | 9022 341 1050 | Spline screw IS-M5x25 | 3 |
| 8 | 4137 020 1201 | Cylinder with piston Ø 34 mm | 1 |
| 9 | 4137 030 2010 | Piston Ø 34 mm | 1 |
| 10 | 4137 034 3000 | Piston ring Ø 34x1.5 mm | 2 |
| 11 | 4137 034 1500 | Piston pin 8x5x22 | 1 |
| 12 | 9463 650 0805 | Snap ring 8x0.7 | 2 |
| 13 | 9512 003 1830 | Needle cage 8x11x10 | 1 |
| 14 | 4137 029 2300 | Cylinder gasket | 1 |
| 15 | 9075 478 4159 | Pan head self-tapping screw IS-D5x24 | 4 |
| 16 | 1110 400 7005 | Spark plug Bosch WSR 6 F | 1 |
| 17 | 0000 998 0606 | Torsion spring | 1 |
| 18 | 1106 405 1000 | Spark plug boot → replaced by 1128 405 1000, 1128 405 1000 TI 30/1995 | 1 |
| 19 | 0783 830 2000 | Tube of sealant Dirko HT red option | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · BG 75
BG 75: new powerhead, performance and sound levels
25.4 cm³, 34x28 mm, 0.75 kW; same intended applications as BG 72.
- BG 75 replaces BG 72 with more torque and power, for the same applications/users. Five-part precision-machined crankshaft; four-port cylinder with larger cooling area; larger-volume improved-material filter; two-chamber muffler with easier spark-arrestor servicing; ElastoStart handle. These design descriptions do not establish component interchange.
- Engine 25.4 cm³ (1.55 cu.in), bore 34 mm (1.34 in), stroke 28 mm (1.10 in), power 0.75 kW (1.0 PS). In blower mode, flow 640 m³/h (359 cfm), speed 60 m/s (198 ft/s). Complete unit WITHOUT TOOLS 4.3 kg (9.6 lb); not a dry-weight statement.
- Blower weighted equivalent sound pressure Lpeq 89 dB(A), ISO 6081; sound power Lweq 100 dB(A), ISO 3744. Footnote weights idle/full-load/no-load for EQUAL exposure durations; these are not interchangeable acoustic metrics.
- Page 2 specification line labels “Muffler: Intake air silencer”, while the technical description separately calls the muffler two-chamber. Preserve this wording rather than silently treating intake and exhaust silencers as the same part.
- Historical BG 75 type 4227 evidence only; BG 72 replacement is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.
Source: TI 16/1996, p. 1 · TI 16/1996, p. 2 · TI 16/1996, p. 4 — new powerhead, performance and sound levels.
No additional parts-table entry added.
Service note · BG 75
BG 75: ignition data and unresolved inch conversions
NGK BPMR7A, 0.5 mm electrode gap; printed metric/inch mismatches retained.
- Gap0.2–0.5 mm (0.008–0.019 in); timing 1.55–2.25 mm BEFORE TDC at 8000 rpm, but parenthesis prints 0.067–0.086 in. These timing pairs are NOT equivalent; do not silently repair the source or treat the inch pair as verified.
- Ignition lead length 160 mm (7.1 in as printed): the two values conflict. Spark plug suppressed NGK BPMR7A, heat range 200, electrode gap 0.5 mm (0.02 in); thread M14x1.25, 9.5 mm (0.37 in) long. Current IPL lists Bosch WSR6F instead; no automatic equivalence or supersession established.
- No part number is invented for the NGK plug or160 mm lead. Specifications are source claims, not measured timing or verified hardware.
- Historical BG 75 type 4227 evidence only; BG 72 replacement is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.
Source: TI 16/1996, p. 1 · TI 16/1996, p. 4 — ignition data and unresolved inch conversions.
No additional parts-table entry added.
Service note · BG 75
BG 75: seal extractor conversion and service aids
20 mm longer spindle converts old extractor; usual BG 72 tools and repair times referenced.
- Oil-seal extractor 5910 890 4400 and spindle 5910 890 8400 are new required service tools. Replacing the previous spindle in extractor 0000 890 4400 with 5910 890 8400, which is20 mm LONGER, makes it identical to 5910 890 4400. This is spindle replacement, not modification of the extractor body or a universal puller conversion.
- Other repairs use the usual BG 72 special tools. Repair times are the same as BG 72, but no durations or complete tool list are supplied. A separate BG 75 parts list is available; current exact-model IPL is retained locally. Gasket sheet 0457 281 4203 is listed as an aid, not a model-specific pre-cut gasket.
- Historical BG 75 type 4227 evidence only; BG 72 replacement is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.
Source: TI 16/1996, p. 1 · TI 16/1996, p. 4 · TI 16/1996, p. 5 · TI 16/1996, p. 6 — seal extractor conversion and service aids.
Part numbers (4)
- 5910 890 4400 — Oil-seal extractorTI16/1996 listed item · BG 75 service tool
- 5910 890 8400 — 20 mm longer replacement spindleTI16/1996 listed item · Conversion of0000 890 4400
- 0000 890 4400 — Previous extractorTI16/1996 listed item · Comparison/conversion only
- 0457 281 4203 — Gasket sheetTI16/1996 listed item · Service aid
Service note · BG 75
BG 75: crankcase and carburetor test pressures
Crankcase ±0.5 bar; inlet needle+0.6 bar; safety prerequisite retained.
- Crankcase leakage test: OVERPRESSURE 0.5 bar and UNDERPRESSURE 0.5 bar. Carburetor inlet needle: OVERPRESSURE 0.6 bar. Vacuum magnitude is not0.5 bar absolute; inlet needle value must not be assigned to crankcase.
- No holding time, permitted decay or complete isolation/test setup is supplied in this TI. If started during repair/maintenance, follow country-of-use safety regulations and Owner’s Manual safety instructions. No unattended operating procedure or hardware test is implied. Exact Owner’s Manual dependency is not supplied by this TI.
- Historical BG 75 type 4227 evidence only; BG 72 replacement is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.
Source: TI 16/1996, p. 1 · TI 16/1996, p. 5 — crankcase and carburetor test pressures.
No additional parts-table entry added.
Service note · BG 75
BG 75: fastener-specific torque table and ambiguous crankcase row
All 17 torque values retained; no blanket torque based only on thread size.
- All values Nm. Socket-head IS-M5x25 crankcase 9.5; second IS-M5x25 row prints “Crankcase” on one line and “Spacer flange to cylinder” on the next, with5.5 aligned to the latter. Preserve that ambiguous two-line label; do not replace the9.5 crankcase value wholesale with5.5.
- IS-DG5x24 cylinder to crankcase 9.5; IS-M5x16 muffler to cylinder 9.5, starter to crankcase 5.5, muffler to crankcase 9.5. IS-M4x25x10 intake screen 2.5; M8 carrier 20.0; IS-M4x20 ignition module to cylinder 4.5.
- Plastoform IS-P5.5x12 rope rotor in starter cover 2.5; IS-P6x19 shroud/fan housing 3.5 and fuel tank/fan housing 3.5. M8 nuts: shaft ZS/crankshaft 21.0, fanwheel/shaft 18.0. M5 nut air-filter cover AND carburetor to cylinder 4.0. IS-P6x26.5 fan housing halves5.5; M14x1.25 spark plug 20.0.
- Carrier row has no fastener designation in the first column; do not invent one. No lubricated-thread condition or staged tightening sequence stated. Different components sharing M8 or M5 threads retain different values.
- Historical BG 75 type 4227 evidence only; BG 72 replacement is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.
Source: TI 16/1996, p. 1 · TI 16/1996, p. 6 — fastener-specific torque table and ambiguous crankcase row.
No additional parts-table entry added.
Wrong number or missing part for the BG 75? Report a correction →