← BG 75

Stihl 4227 · Section B · 2 of 8 · 28 parts

Rewind starter, Ignition system

Fits BG 75.

Parts diagrams →

Historical fitment & changes (12) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314141415161718192202122232425253456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (28)

PosPart numberDescriptionQty
1 4133 190 2002 Carrier 1
2 4133 195 7201 Pawl 1
3 0000 998 0612 Torsion spring 1
4 4137 190 0400 Starter cover 1
5 4137 190 1100 Rope rotor with rewind spring Fitment / change note → 1
6 0000 190 3403 Starter grip ElastoStart Ø 2,7 mm Fitment / change note → 1
7 4137 195 8200 Starter rope Ø 2.7x910 mm Fitment / change note → 1
8 0000 190 3400 Starter grip ElastoStart Ø 3 mm Fitment / change note → → replaced by 0000 190 3403, 0000 190 3403 TI 42/1999 1
9 0000 195 8200 Starter rope Ø 3x800 mm Fitment / change note → 1
10 0000 195 7000 Cap 1
11 9104 003 0960 Self-tapping screw P5.5x12 1
12 4227 084 2201 Guard Fitment / change note → 1
13 4227 967 1501 Model plate BG 75 1
14 9022 341 0980 Spline screw IS-M5x16 6
15 4227 149 0610 Muffler gasket 1
16 4227 140 0602 Muffler 1
17 4137 141 9000 Screen 1
18 9099 021 0810 Self-tapping screw 4.2x9.5 1
19 4137 400 1200 Flywheel Fitment / change note → 1
20 4137 400 1350 Ignition module Fitment / change note → 1
21 4137 405 1600 Plug connector 1
22 4137 404 9300 Washer 2
23 9022 371 0710 Spline screw IS-M4x20 2
24 4227 704 0500 Shaft 1
25 4227 440 1101 Short circuit wire 190 mm / 7.5'' 2
Not numbered on the diagram — assemblies, kits and options
— 4137 190 4000 Rewind starter 1
— 0000 930 2281 Starter rope Ø 2.7 mm x 30.8 m not illustratedoption 1
— 0000 930 2208 NLA Starter rope Ø 3 mm x 30.5 m not illustratedoption 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · BG 75

BG 75: series 4227 replacement ignition assignment

4137 400 1307 with flywheel 4137 400 1200; ignition lead not replaceable.

  • Printed series 4227. Use 4137 400 1307 with flywheel 4137 400 1200.
  • The asterisk means ignition lead not replaceable; it is not a zero or unspecified cut length.
  • TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
  • Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
  • Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
  • Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
  • Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.

Source: TI 1/1999, p. 1 · TI 1/1999, p. 3 — 1.1 general restrictions and 1.2.2 power-tool assignments.

Part numbers (2)
  • 4137 400 1307 — Replacement ignition moduleAssigned component · BG 75, printed series 4227, listed combination only
  • 4137 400 1200 — Assigned flywheelRequired pairing · BG 75, printed series 4227

Conditional replacement · BG 75

BG 75: replacement ignition kit has special instructions

The replacement number also applies to BG 75; its installation notes are in the separate kit instructions.

  • Section 4.3 explicitly extends the replacement-number change from 4137 400 1307 to kit 4137 400 1350 to BG 75. The kit contains MB hardware. The insulating tube 4137 442 0400 is not required on BG 75.
  • BG 75-specific special notes are in the separate kit installation instructions, not located in the retained inventory. General BG75 workshop procedures are not established as those kit instructions; this remains a documented source gap. This subsection does not prove AD production installation on BG 75 or assign it an ignition introduction serial. Do not borrow the HS guard changes.
  • Only explicitly named models/configurations are covered; shared IPL sheets do not extend this note to other variants. Availability describes 2001 factory supply, not present stock. Retained engine-sheet series are navigation, not proof of series equivalence.

Source: TI 16/2001, p. 8 · TI 16/2001, p. 9 — Sections 4.3–4.4: BG 75-specific kit dependency and tube exception.

Part numbers (3)
  • 4137 400 1307 — Ignition module type MBPrevious separate module · BG 75; named configuration only
  • 4137 400 1350 — Type MB ignition module kitReplacement for MB and AD · BG 75; named configuration only
  • 4137 442 0400 — Insulating tubeUnchanged; omitted on BG 75 and HS 75/80/85 · BG 75; named configuration only

Conditional replacement · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / KM 85 / FS 75 / FS 80 / FS 85 / BG 72 / BG 75 / FC 72 / FS 72 / FS 74 / FS 76 / HS 75 / HS 80 / HS 85 / HS 72 / HS 74 / HS 76

TI24/2002: three starter-rope stages and model scope

Keep the original, interim and final rope sizes separate; HS72/74/76 do not inherit the grip change.

  • Original starter rope 4123 195 8200 is 0.105 in / 2.7 mm diameter and 31.5 in / 800 mm long. Interim rope 0000 195 8200 is 0.120 in / 3 mm diameter and the same 31.5 in / 800 mm length. Final rope 4137 195 8200 returns to 0.105 in / 2.7 mm diameter but increases length to 35.8 in / 910 mm. Do not confuse unchanged diameter with unchanged length.
  • The interim rope is included in ElastoStart 0000 190 3400; the final rope is used in ElastoStart 0000 190 3403. Those grip associations describe the main starter branch; section 2.7 extends subsections 2.1, 2.3, 2.4 and 2.5 to HS 72, HS 74 and HS 76, but not subsection 2.2. No ElastoStart-grip replacement is authorized for those three models by this TI.
  • Summary remarks distinguish earlier-to-interim from interim-to-new changes. Original rope 4123 195 8200 and interim rope 0000 195 8200 remain available for other models; their removal from this branch does not mean universal discontinuation. Section 2.6 states the new starter parts are fully interchangeable with previous machine versions within the applicable section 2 model scope.
  • These are section 2 starter changes, not section 1 control-handle/throttle-cable retrofit permission. Main models come from the heading; additional models follow section 2.7. The old series 4112 FS 80 is not bound merely because its name matches. Shared IPL sheets do not extend applicability to unnamed variants. Introduction is in progress without a starter serial cutoff; factory availability is historical, not current stock. No physical interchange test was performed.

Source: TI 24/2002, p. 1 · TI 24/2002, p. 8 · TI 24/2002, p. 9 — Heading model scope; section2 starter diagram, subsections2.1–2.8 and ten-row summary/six remarks.

Part numbers (3)
  • 4123 195 8200 — Starter rope 2.7 x 800 mmOriginal; retained for other models · Named section 2 models only; see conditions
  • 0000 195 8200 — Starter rope 3 x 800 mmInterim; retained for other models · Named section 2 models only; see conditions
  • 4137 195 8200 — Starter rope 2.7 x 910 mmFinal version · Named section 2 models only; see conditions

Conditional replacement · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / KM 85 / FS 75 / FS 80 / FS 85 / BG 72 / BG 75 / FC 72 / FS 72 / FS 74 / FS 76 / HS 75 / HS 80 / HS 85

TI24/2002: ElastoStart grip change excludes HS72/74/76

The new grip follows the longer final rope; do not extend subsection2.2 to the restricted hedge-trimmer group.

  • ElastoStart grip 0000 190 3403 replaces 0000 190 3400 together with the introduction of final rope 4137 195 8200 (2.7 x 910 mm). The old grip includes interim rope 0000 195 8200 (3 x 800 mm); the new grip includes the final rope. Summary rows 4–7 preserve these assembly contents.
  • The old grip and interim rope remain available for other models. Full starter modifications also apply to BG 72, BG 75, FC 72, FS 72, FS 74, FS 76, HS 75, HS 80 and HS 85. HS 72, HS 74 and HS 76 are deliberately excluded from this grip note: their subsection list omits 2.2.
  • The section 2.6 interchangeability statement belongs to this starter update; it does not remove the explicit model/subsection limitation or the separate control-handle retrofit conditions.
  • These are section 2 starter changes, not section 1 control-handle/throttle-cable retrofit permission. Main models come from the heading; additional models follow section 2.7. The old series 4112 FS 80 is not bound merely because its name matches. Shared IPL sheets do not extend applicability to unnamed variants. Introduction is in progress without a starter serial cutoff; factory availability is historical, not current stock. No physical interchange test was performed.

Source: TI 24/2002, p. 1 · TI 24/2002, p. 8 · TI 24/2002, p. 9 — Heading model scope; section2 starter diagram, subsections2.1–2.8 and ten-row summary/six remarks.

Part numbers (4)
  • 0000 190 3400 — ElastoStart grip with interim ropePrevious; retained for other models · Named section 2 models only; see conditions
  • 0000 190 3403 — ElastoStart grip with final ropeNew · Named section 2 models only; see conditions
  • 0000 195 8200 — Starter rope 3 x 800 mmOld grip content · Named section 2 models only; see conditions
  • 4137 195 8200 — Starter rope 2.7 x 910 mmNew grip content · Named section 2 models only; see conditions

Conditional replacement · FH 75 / HL 75 / HT 70 / HT 75 / FC 75 / FC 85 / KW 85 / KM 85 / FS 75 / FS 80 / FS 85 / BG 72 / BG 75 / FC 72 / FS 72 / FS 74 / FS 76 / HS 75 / HS 80 / HS 85 / HS 72 / HS 74 / HS 76

TI24/2002: rope rotor and spring supplied as an assembly

Preserve the interim-rotor availability conflict; new rotor and spring are not separate spares.

  • Original rope rotor 4133 195 0400 was replaced by interim rotor 4133 195 0470. The TI says the interim rotor is no longer available separately and the rewind spring 4133 195 1600 is likewise supplied only as part of rope rotor with rewind spring 4137 190 1100. The new assembly contains the rotor and spring; no independent new numbers are given for either component.
  • The starter drawing labels rope (1), ElastoStart grip (2), rotor (3), spring (4), and rotor/spring assembly (5). These are not the summary-table row numbers: assembly 4137 190 1100 is summary item 8, with its spring and rotor as items 9 and 10.
  • Preserved source tension: prose and summary remark 4 say the interim rotor is no longer available from the factory, while summary item 10 (previous rotor 4133 195 0470) carries remark 3 permitting previous stock until exhausted. Spring item 9 also carries the stock remark despite prose saying it is no longer separate. New separate items are explicitly unavailable under remark 6; use assembly item 8. Do not silently collapse these phase/stock statements into a current availability promise.
  • Section 2.7 explicitly extends subsections 2.3–2.5, as well as rope subsection 2.1, to HS 72, HS 74 and HS 76. The broader group receives all starter modifications. Section 2.6 states full interchangeability with previous versions within this starter scope, not a control-handle equivalence rule. All other parts are stated unchanged.
  • These are section 2 starter changes, not section 1 control-handle/throttle-cable retrofit permission. Main models come from the heading; additional models follow section 2.7. The old series 4112 FS 80 is not bound merely because its name matches. Shared IPL sheets do not extend applicability to unnamed variants. Introduction is in progress without a starter serial cutoff; factory availability is historical, not current stock. No physical interchange test was performed.

Source: TI 24/2002, p. 1 · TI 24/2002, p. 8 · TI 24/2002, p. 9 — Heading model scope; section2 starter diagram, subsections2.1–2.8 and ten-row summary/six remarks.

Part numbers (4)
  • 4133 195 0400 — Rope rotorOriginal; stocks-only phase · Named section 2 models only; see conditions
  • 4133 195 0470 — Rope rotorInterim; conflicting separate-stock statements · Named section 2 models only; see conditions
  • 4133 195 1600 — Rewind springPrevious separate part; stock/assembly statements retained · Named section 2 models only; see conditions
  • 4137 190 1100 — Rope rotor with rewind springNew assembly; includes both components · Named section 2 models only; see conditions

Service note · BG 75

BG 75: starter dimensions and spring reserve

3.0 mm x800 mm rope; seven rotor turns and at least half-turn reserve.

  • ElastoStart system: starter rope diameter 3.0 mm (0.12 in), length 800 mm (31.5 in). Rewind spring tension SEVEN turns of rope rotor; reserve pull MINIMUM 1/2 turn. Do not substitute seven crankshaft revolutions or omit the reserve.
  • Current BG 75 IPL also lists2.7x910 mm rope alongside3x800 mm. This later alternative does not change the TI dimensions or establish that every starter version accepts both.
  • Historical BG 75 type 4227 evidence only; BG 72 replacement is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.

Source: TI 16/1996, p. 1 · TI 16/1996, p. 2 — starter dimensions and spring reserve.

No additional parts-table entry added.

Service note · BG 75

BG 75: ignition data and unresolved inch conversions

NGK BPMR7A, 0.5 mm electrode gap; printed metric/inch mismatches retained.

  • Gap0.2–0.5 mm (0.008–0.019 in); timing 1.55–2.25 mm BEFORE TDC at 8000 rpm, but parenthesis prints 0.067–0.086 in. These timing pairs are NOT equivalent; do not silently repair the source or treat the inch pair as verified.
  • Ignition lead length 160 mm (7.1 in as printed): the two values conflict. Spark plug suppressed NGK BPMR7A, heat range 200, electrode gap 0.5 mm (0.02 in); thread M14x1.25, 9.5 mm (0.37 in) long. Current IPL lists Bosch WSR6F instead; no automatic equivalence or supersession established.
  • No part number is invented for the NGK plug or160 mm lead. Specifications are source claims, not measured timing or verified hardware.
  • Historical BG 75 type 4227 evidence only; BG 72 replacement is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.

Source: TI 16/1996, p. 1 · TI 16/1996, p. 4 — ignition data and unresolved inch conversions.

No additional parts-table entry added.

Service note · BG 75

BG 75: fastener-specific torque table and ambiguous crankcase row

All 17 torque values retained; no blanket torque based only on thread size.

  • All values Nm. Socket-head IS-M5x25 crankcase 9.5; second IS-M5x25 row prints “Crankcase” on one line and “Spacer flange to cylinder” on the next, with5.5 aligned to the latter. Preserve that ambiguous two-line label; do not replace the9.5 crankcase value wholesale with5.5.
  • IS-DG5x24 cylinder to crankcase 9.5; IS-M5x16 muffler to cylinder 9.5, starter to crankcase 5.5, muffler to crankcase 9.5. IS-M4x25x10 intake screen 2.5; M8 carrier 20.0; IS-M4x20 ignition module to cylinder 4.5.
  • Plastoform IS-P5.5x12 rope rotor in starter cover 2.5; IS-P6x19 shroud/fan housing 3.5 and fuel tank/fan housing 3.5. M8 nuts: shaft ZS/crankshaft 21.0, fanwheel/shaft 18.0. M5 nut air-filter cover AND carburetor to cylinder 4.0. IS-P6x26.5 fan housing halves5.5; M14x1.25 spark plug 20.0.
  • Carrier row has no fastener designation in the first column; do not invent one. No lubricated-thread condition or staged tightening sequence stated. Different components sharing M8 or M5 threads retain different values.
  • Historical BG 75 type 4227 evidence only; BG 72 replacement is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.

Source: TI 16/1996, p. 1 · TI 16/1996, p. 6 — fastener-specific torque table and ambiguous crankcase row.

No additional parts-table entry added.

Historical fitment · BG 72 / BG 75

BG 72 / BG 75 guard: starter-cover/crankcase change

4227 084 2200 → 4227 084 2201 shares the shroud changeover.

X 30 310 719 — Shroud and guard modification introduced from this machine number on the BG72/BG75 bulletin scope;not a universal whole-machine or handle cutoff.

  • Section3 identifies the guard BETWEEN STARTER COVER AND CRANKCASE. Guard 4227 084 2200 is replaced by 4227 084 2201 FROM X 30 310 719 to suit the section2 shroud modification. The prose and one-row summary agree;do not extend this number to every assembly change.
  • The unnumbered guard drawing shows its shape and mounting features;it supplies no dimensions,fastener torque or alternative part mapping. The original version is no longer factory-available in this1996 notice;no reverse-fitment permission or current availability is established.
  • Page2 copyright1996 and D1/MTK-al documentation code5912 are provenance,not serials or part numbers. The header,section/table/remark blocks and otherwise blank page areas contain no additional ordering assertions.
  • TI42/1996 covers BG 72 and BG 75, printed series4227. Later 2012 BG75 IPL sheets are navigation, not an original1996 configuration or a BG72 IPL. No hardware operation was performed.

Source: TI 42/1996, p. 2 — BG 72 / BG 75 guard: starter-cover/crankcase change.

Part numbers (2)
  • 4227 084 2200 — GuardOriginal version · BG72/BG75;between starter cover and crankcase
  • 4227 084 2201 — GuardNew version · BG72/BG75 from X30310719;linked shroud modification

Service note · BG 75 / FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75 / HS 75 / HS 80 / HS 85

ESL ignition modules: 1306/1307 marking and the optional BG/HS hose

1307 adds the insulating hose and is the general replacement.

  • WHEN DISASSEMBLED, marking XXXX = 1306 OR 1307 identifies an ESL module. Drawing366TI021 KN reads STIHL 4137 XXXX A and calls the hose5; that drawing callout is not summary item 5. No complete order number is invented for marking 1306.
  • Version 1307 differs from 1306 ONLY THROUGH THE ADDITIONAL INSULATING HOSE on the ignition cable and is generally supplied as a replacement. BG AND HS machines DO NOT REQUIRE the hose, but MAY INSTALL THE NEW MODULE WITH THE HOSE.
  • Summary module 4137 400 1305 becomes 4137 400 1307 INCLUDING ITEM 2, hose 4137 442 0400 unchanged. Remark1 says original NO LONGER AVAILABLE FROM FACTORY. The BG 75 paragraph separately permits residual 1305 stock ONLY FOR BG 75; this is not general permission to install a non-ESL module elsewhere.
  • For listed machines without a carburetor speed-control valve, the service rule requires 4137 400 1307 with ESL; BG 75 has the explicitly separate fan-load exception. Marking identification alone is not an operating test or permission to bypass speed limiting.
  • Historical TI 41/1997 evidence for the named models and configurations only; not present stock, a universal serial-to-model registry or verified physical interchange. No hardware operation was performed.

Source: TI 41/1997, p. 3 · TI 41/1997, p. 4 — Section 1.2.2.1 and drawing 366TI021 KN; section 1.2.2.2; summary ignition module/item 2/remark1.

Part numbers (3)
  • 4137 400 1305 — Original ignition moduleNo longer factory supplied; BG 75 residual-stock exception · Only the named TI 41/1997 configurations and conditions
  • 4137 400 1307 — Replacement ESL ignition module including hose item 2General replacement · Only the named TI 41/1997 configurations and conditions
  • 4137 442 0400 — Insulating hose; summary item 2Unchanged part number · Only the named TI 41/1997 configurations and conditions

Service note · BG 75

BG 75 only: fan load makes separate speed limiting unnecessary

ESL 1307 standardizes replacements; old 1305 may be used only here while stocks last.

  • The BG 75 paragraph says FAN-WHEEL POWER DEMAND makes maximum-speed limitation by EITHER CARBURETOR OR IGNITION MODULE unnecessary ON THIS MODEL. This exception does not extend to BG 72 or any FS, FC, HS, HL or HT model.
  • Nevertheless ESL 4137 400 1307 is used for replacements to standardize with other models. Former 4137 400 1305 may be used ONLY FOR THIS MODEL WHILE STOCKS LAST. This residual-stock permission is distinct from the summary saying the original module is no longer factory available.
  • No BG 75 changeover number, maximum RPM or authority to run without its fan wheel is supplied. The hose is not required for BG but may remain fitted.
  • Historical TI 41/1997 evidence for the named models and configurations only; not present stock, a universal serial-to-model registry or verified physical interchange. No hardware operation was performed.

Source: TI 41/1997, p. 3 · TI 41/1997, p. 4 — Section 1.2.2.2 BG 75 exception; section 1.2.2.1 hose and summary remark1.

Part numbers (2)
  • 4137 400 1305 — Former ignition moduleBG 75 only while stocks last · Only the named TI 41/1997 configurations and conditions
  • 4137 400 1307 — ESL replacement ignition moduleStandardized BG 75 replacement · Only the named TI 41/1997 configurations and conditions

Service note · BG 75 / FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75 / HS 75 / HS 80 / HS 85 / BG 72 / FC 72 / FS 48 / FS 52 / FS 56 / FS 62 / FS 66 / FS 72 / FS 74 / FS 76 / HS 72 / HS 74 / HS 76

ElastoStart replacement rope: original-number conflict retained

New 0000 195 8200 is3.0×800 mm; prose and table disagree on the original.

continuously — Continuous introduction; no numeric boundary supplied for this particular change.

  • Section 3 prose prints ORIGINAL 4123 190 4000 (2.7×900 mm), replaced for some time by ELASTOSTART 0000 195 8200 (3.0×800 mm). The summary instead prints ORIGINAL 4123 195 8200. Both are confirmed on the original scan: retain the UNRESOLVED NUMBER CONFLICT, not an OCR correction, proven equivalence or two-step supersession.
  • In addition to cover models, the source explicitly extends this change to BG 72, FC 72, FS 48/52/56/62/66/72/74/76 and HS 72/74/76. These are the historical configurations: not the later type 4144 FS 56 or type 4112 FS 80.
  • Modification introduced CONTINUOUSLY; summary remark says ORIGINAL NO LONGER AVAILABLE FROM FACTORY. No machine-number cutoff, handle assembly replacement, knot procedure or permission to shorten either rope to an unprinted length is given. Catalog associations expose the historical note without rewriting their rope rows or choosing which conflicting original is correct.
  • Historical TI 41/1997 evidence for the named models and configurations only; not present stock, a universal serial-to-model registry or verified physical interchange. No hardware operation was performed.

Source: TI 41/1997, p. 5 — Entire section 3 prose, extended model list, summary and availability remark.

Part numbers (3)
  • 4123 190 4000 — Original rope number printed in prose;2.7×900 mmConflicts with summary original · Only the named TI 41/1997 configurations and conditions
  • 4123 195 8200 — Original rope number printed in summaryConflicts with prose original · Only the named TI 41/1997 configurations and conditions
  • 0000 195 8200 — ElastoStart rope;3.0×800 mmReplacement · Only the named TI 41/1997 configurations and conditions

Wrong number or missing part for the BG 75? Report a correction →