← BG 75

Stihl 4227 · Section C · 3 of 8 · 32 parts

Air filter, Fuel tank

Fits BG 75.

Parts diagrams →

Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101111121314151617181922021222324252626272829330456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (32)

PosPart numberDescriptionQty
1 4227 129 0905 Gasket 1
2 9007 319 1137 Hexagon head screw M5x68 2
3 4137 121 1600 Spacer flange 1
4 9291 021 0121 Washer 5.3 2
5 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 2
6 4137 122 5300 Insulator 1
7 4227 129 0906 Gasket 1
8 4137 129 0900 Gasket 1
9 4227 120 0604 Carburetor C1Q-S47A 1
9 4227 120 0602 Carburetor C1Q-S30C 1
9 not sold separately Carburetor WT-413 no longer available from factory 1
10 4227 122 1805 Heat shield 1
11 4114 149 1205 Gasket Fitment / change note → 2
12 4137 140 2800 Filter housing 1
13 4137 141 3700 Lever 1
14 4137 141 3800 Choke shutter 1
15 9417 003 7512 Push nut 4.0x9.6x1.8 1
16 9210 261 0700 Hexagon nut M5 2
17 4137 124 2800 Filter 1
18 4137 124 1500 Prefilter 1
19 4137 141 0500 Filter cover 1
20 4227 350 0400 Fuel tank 1
21 4227 358 0800 Hose 185 mm / 7 5/16'' 1
22 4227 358 0805 Hose 235 mm / 9 1/4'' 1
23 0000 989 0516 Grommet 2
24 9074 478 4425 Pan head self-tapping screw IS-P6x19 2
25 9307 021 0120 Washer 5.3 2
26 0000 350 3502 Pickup body 1
27 0000 358 1800 Filter 1
28 4128 350 0505 Filler cap 1
29 0000 350 0900 Rope 1
30 0000 353 0800 Filler cap retainer 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · BG 75

BG 75: historical fuel, oil and filter specification

0.5 l tank; regional octane and California oil-ratio restrictions retained.

  • All-position diaphragm carburetor with integral fuel pump; foam prefilter and felt filter. Tank 0.5 l (0.9 US pt as printed). Regular branded gasoline and branded two-stroke oil; 90 RON, with U.S.A./Canada minimum89 RON explicitly printed. Do not silently reinterpret RON as pump AKI.
  • Mixing proportions:1:50 with STIHL two-stroke engine oil1:50; 1:25 with other branded two-stroke oils. California footnote permits ONLY two-stroke engine oils in1:50 ratio. Historical source specification, not a universal current-fuel recommendation.
  • Historical BG 75 type 4227 evidence only; BG 72 replacement is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.

Source: TI 16/1996, p. 1 · TI 16/1996, p. 3 — historical fuel, oil and filter specification.

No additional parts-table entry added.

Service note · BG 75

BG 75: fastener-specific torque table and ambiguous crankcase row

All 17 torque values retained; no blanket torque based only on thread size.

  • All values Nm. Socket-head IS-M5x25 crankcase 9.5; second IS-M5x25 row prints “Crankcase” on one line and “Spacer flange to cylinder” on the next, with5.5 aligned to the latter. Preserve that ambiguous two-line label; do not replace the9.5 crankcase value wholesale with5.5.
  • IS-DG5x24 cylinder to crankcase 9.5; IS-M5x16 muffler to cylinder 9.5, starter to crankcase 5.5, muffler to crankcase 9.5. IS-M4x25x10 intake screen 2.5; M8 carrier 20.0; IS-M4x20 ignition module to cylinder 4.5.
  • Plastoform IS-P5.5x12 rope rotor in starter cover 2.5; IS-P6x19 shroud/fan housing 3.5 and fuel tank/fan housing 3.5. M8 nuts: shaft ZS/crankshaft 21.0, fanwheel/shaft 18.0. M5 nut air-filter cover AND carburetor to cylinder 4.0. IS-P6x26.5 fan housing halves5.5; M14x1.25 spark plug 20.0.
  • Carrier row has no fastener designation in the first column; do not invent one. No lubricated-thread condition or staged tightening sequence stated. Different components sharing M8 or M5 threads retain different values.
  • Historical BG 75 type 4227 evidence only; BG 72 replacement is not parts interchangeability. No serial cutoff or calendar introduction date is supplied. No hardware operation was performed.

Source: TI 16/1996, p. 1 · TI 16/1996, p. 6 — fastener-specific torque table and ambiguous crankcase row.

No additional parts-table entry added.

Service note · BG 75 / FC 75 / FS 75 / FS 80 / FS 85 / HL 75 / HT 75 / HS 75 / HS 80 / HS 85

Heat-shield sealing: one 4114 149 1205 gasket on each side

Fit missing gaskets on original-version machines; total quantity two.

  • Section 4 says 4114 149 1205 (1) has for some time been fitted ON BOTH SIDES OF HEAT SHIELD (2) to improve sealing. Drawing366TI023 GM places one gasket between carburetor and shield and another between shield and the air-filter side. The summary explicitly says GASKET (2x).
  • Service note: MISSING GASKETS MUST BE FITTED IN MODELS WITH THE ORIGINAL VERSION. Continuous introduction; no numeric cutoff. Do not stack both on one side, interpret2x as two pairs, invent a shield number or transfer this instruction to unlisted successor models.
  • The footer lists last TIs BG 75 TI 42.96 (TI 27.97 USA only), FC/FS/HL/HT TI 37.97 and HS TI 04.97. These are bibliographic history, not delegated procedures required to apply this gasket note; no missing-source closure claim is created from the footer alone.
  • Historical TI 41/1997 evidence for the named models and configurations only; not present stock, a universal serial-to-model registry or verified physical interchange. No hardware operation was performed.

Source: TI 41/1997, p. 6 — Complete section 4, drawing 366TI023 GM, quantity 2 summary, service note and footer.

Part numbers (1)
  • 4114 149 1205 — Heat-shield gasket; drawing 1, quantity 2Fit missing gaskets · Only the named TI 41/1997 configurations and conditions

Wrong number or missing part for the BG 75? Report a correction →