← HS 45

Stihl 4228 · Section C · 3 of 10 · 38 parts

Air filter, Fuel tank

Fits HS 45.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161718192202122232425272829330313233343536456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (38)

PosPart numberDescriptionQty
1 4140 124 2800 Filter Fitment / change note → 1
2 4228 124 1500 Prefilter Fitment / change note → 1
3 4228 140 2850 Filter housing Fitment / change note → 1
4 4140 141 3700 Lever Fitment / change note → 1
5 4140 141 3801 Choke shutter Fitment / change note → → replaced by 4601 007 1009 TI 28/2004 1
6 4140 141 3800 NLA Choke shutter Fitment / change note → 1
7 9417 003 7512 Push nut 4.0x9.6x1.8 Fitment / change note → 1
8 4228 141 0502 Filter cover Fitment / change note → 1
9 4228 141 0500 Filter cover Fitment / change note → 1
10 9210 261 0700 Hexagon nut M5 2
11 4140 129 0900 Gasket 1
12 4228 120 0608 Carburetor C1Q-S169A 1
13 4228 120 0609 Carburetor C1Q-S170A 1
14 4228 120 0603 Carburetor C1Q-S67 Fitment / change note → no longer available from factory 1
15 4228 120 0601 Carburetor C1Q-S54A Fitment / change note → 1
16 4228 120 0600 Carburetor C1Q-S49B Fitment / change note → no longer available from factory 1
17 4114 149 1205 Gasket 1
18 4140 121 1605 Spacer flange Fitment / change note → 1
19 4140 182 7602 Tensioner Fitment / change note → 1
20 4137 123 8900 Pin Fitment / change note → 1
21 9417 003 7512 Push nut 4.0x9.6x1.8 Fitment / change note → 1
22 9022 313 0680 Spline screw IS-M4x16 1
23 9075 478 4159 Pan head self-tapping screw IS-D5x24 2
24 9007 319 1135 Hexagon head screw M5x65 2
25 4228 129 0905 Gasket 1
27 4228 358 0800 Hose 1
28 0000 350 3503 Pickup body 1
29 not sold separately Hose 3.1x5.7x94 mm, R3 not available as a separate item 1
30 0000 989 0516 Grommet 1
31 4226 350 0503 Filler cap 1
32 4226 350 0900 Rope 1
33 0000 353 0800 Filler cap retainer 1
34 0000 351 3201 Sleeve 3
35 1125 084 8900 Grommet 3
36 9074 478 4140 Pan head self-tapping screw IS-P6x25 3
Not numbered on the diagram — assemblies, kits and options
— 0000 930 2803 Hose 3.1x5.7 mm x 1 m, R3 not illustratedoption 1
— 0712 923 8004 Hose 3.1x5.7 mm x 10 m, R3 not illustratedoption 1
— 4228 007 1050 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · HS 45

HS 45 LD carburetor: paired flange and end cover

C1Q-S54 replaces C1Q-S49B; old-carburetor repairs require the complete paired flange conversion.

  • C1Q-S49B 4228 120 0600 is deleted and replaced by C1Q-S54 4228 120 0601. These are LD/BIS carburetors, not the later H/L/LA C1Q-S67. The retained IPL calls the 0601 sheet C1Q-S54A; the 2001 source says C1Q-S54. The suffix is not silently changed.
  • New end cover 4140 121 0800 and flange 4140 120 2200 can only be used together. Four identical 4226 122 7100 screws secure the combined assembly instead of two short and two long screws; their quantity changes from two to four.
  • For repairs to old carburetor 4228 120 0600 use flange kit 4140 120 2250, including new flange, end cover, gasket, metering diaphragm, four screws and illustrated instructions. New flange and end cover are separately available for the new carburetor only. The diagram shows old separate cover/flange fasteners versus the new combined stack.
  • Previous end cover 4226 121 0800, two screws 1128 122 7100, flange 4226 120 2200 and gasket 1129 129 0900 remain available for other models, not a license to mix the new pair. Metering diaphragm 4129 121 4700 is unchanged. The new gasket is printed 4129 129 0902; do not replace this historical number with the later IPL gasket by assumption.
  • The exact illustrated instructions for kit 4140 120 2250 are a documented retained-corpus source gap: the bounded inventory in docs/ti16-2001-dependencies.json did not locate them. This TI independently supplies the HS 45 applicability and kit roster but does not reproduce that separate sheet.
  • HS 45 only. Factory availability describes the 2001 bulletin, not present stock. No physical interchange or running adjustment was tested.

Source: TI 26/2001, p. 2 · TI 26/2001, p. 3 — Section 3, exploded views, all summary rows and remarks.

Part numbers (12)
  • 4228 120 0600 — Carburetor C1Q-S49BPrevious LD carburetor · HS 45; configuration restrictions in this note
  • 4228 120 0601 — Carburetor C1Q-S54New LD carburetor · HS 45; configuration restrictions in this note
  • 4226 122 7100 — ScrewQuantity two to four · HS 45; configuration restrictions in this note
  • 4226 121 0800 — End coverPrevious · HS 45; configuration restrictions in this note
  • 4140 121 0800 — End coverNew; matched flange required · HS 45; configuration restrictions in this note
  • 1128 122 7100 — ScrewPrevious pair · HS 45; configuration restrictions in this note
  • 4226 120 2200 — FlangePrevious · HS 45; configuration restrictions in this note
  • 4140 120 2200 — FlangeNew; matched cover required · HS 45; configuration restrictions in this note
  • 4129 121 4700 — Metering diaphragmUnchanged · HS 45; configuration restrictions in this note
  • 1129 129 0900 — GasketPrevious · HS 45; configuration restrictions in this note
  • 4129 129 0902 — GasketNew as printed · HS 45; configuration restrictions in this note
  • 4140 120 2250 — Flange conversion kitOld-carburetor repair kit · HS 45; configuration restrictions in this note

Conditional replacement · HS 45

HS 45 C1Q-S67: limiter and service settings

The three-screw carburetor has a 270-degree H limiter; the bulletin distinguishes uncapped service setting from user adjustment.

  • C1Q-S67 4228 120 0603 replaces LD/BIS C1Q-S54 4228 120 0601 as part of the model update package. Introduction is in progress, with no serial cutoff. Previous C1Q-S54 remains a spare for older machines; new-carburetor component parts are referred to the IPL.
  • The H screw has a limiter cap over its knurled head; the body stop pin restricts rotation to 270 degrees (3/4 turn). L and LA have funnel-shaped access caps, not a claimed L mixture limiter.
  • For H-screw replacement or carburetor cleaning the TI removes the H cap with suitable pliers. Never re-use a removed cap because it may be damaged. Check the air filter and spark-arresting screen and clean or replace as necessary.
  • The uncapped standard H service setting is 1 1/2 turns open from lightly seated. Align a new H cap at the rich stop and press it home against the carburetor body. Do not import the two-detent seating instructions of another carburetor.
  • For idle adjustment, L starts one full turn counterclockwise from lightly seated; LA sets 2,800 RPM, checked with a tachometer. Check repeated acceleration and smooth idle. These are source-specific historical instructions, not a universal tuning recipe.
  • Users have 270-degree H adjustment for conditions such as altitude; the TI refers the user procedure to the owner manual, Adjusting the Carburetor. The exact HS 45 owner-manual edition was not located in the bounded retained inventory: a documented source gap, not global absence. The cover illustration shows H 3/4 and L 1; this does not override the explicitly uncapped H service setting of 1 1/2 turns.
  • Edition boundary: the later HS 45 workshop manual RA_253_00_01_01 (2005-03), printed pages 33–35 (PDF 34–36), distinguishes a short cap seated at the second noticeable detent, not against the body, from a long cap seated against the body. It is not the missing 2001 owner manual. Do not identify the TI cap as either later type by assumption; its own body-seating instruction remains source-attributed. Dependency evidence: docs/ti26-2001-dependencies.json.
  • HS 45 only. Factory availability describes the 2001 bulletin, not present stock. No physical interchange or running adjustment was tested.

Source: TI 26/2001, p. 3 · TI 26/2001, p. 4 · TI 26/2001, p. 5 · TI 26/2001, p. 7 — Sections 4, 4.1.1–4.1.9 and 4.5 carburetor rows.

Part numbers (2)
  • 4228 120 0601 — Carburetor C1Q-S54Previous LD generation · HS 45; configuration restrictions in this note
  • 4228 120 0603 — Carburetor C1Q-S67H/L/LA generation · HS 45; configuration restrictions in this note

Conditional replacement · HS 45

HS 45 spacer flange and integral-pivot tensioner

The new tensioner runs on the spacer flange pivot, eliminating the separate pin and its push nut at that location.

  • Spacer flange 4140 121 1605 replaces 4140 121 1600 with the new carburetor; its internal surface structure is revised for fuel/air flow. Tensioner 4140 182 7602 replaces 4140 182 7600 and runs on the integral pivot pin of the new spacer flange.
  • Bearing pin 4137 123 8900 and push nut 9417 003 7512 are no longer required at the tensioner. The same push-nut number remains in the filter-housing assembly; this is not a machine-wide deletion.
  • Previous spacer flange, pin and push nut remain spares for older machines; previous tensioner is supplied only while existing stocks last. Package introduction is in progress, not the separate USA gasket serial cutoff.
  • HS 45 only. Factory availability describes the 2001 bulletin, not present stock. No physical interchange or running adjustment was tested.

Source: TI 26/2001, p. 5 · TI 26/2001, p. 7 — Section 4.2, drawing and 4.5 rows 3–6.

Part numbers (6)
  • 4140 121 1600 — Spacer flangePrevious · HS 45; configuration restrictions in this note
  • 4140 121 1605 — Spacer flange, structured flow surfaceNew integral-pivot version · HS 45; configuration restrictions in this note
  • 4140 182 7600 — TensionerPrevious; stocks only · HS 45; configuration restrictions in this note
  • 4140 182 7602 — TensionerNew integral-pivot pairing · HS 45; configuration restrictions in this note
  • 4137 123 8900 — Bearing pinOmitted at new tensioner · HS 45; configuration restrictions in this note
  • 9417 003 7512 — Push nutOmitted at tensioner, retained at choke · HS 45; configuration restrictions in this note

Conditional replacement · HS 45

HS 45 filter housing: universal replacement kit

Kit 4228 140 2850 serves both carburetor generations, with an unmarked replacement cover and orange choke shutter.

  • The hinge moves to allow access to the new H/L/LA screws, and the production cover carries setting symbols. Replacement filter housing 4228 140 2850 must be used for all HS 45 versions irrespective of carburetor. It includes housing with lever/choke/push nut, filter, prefilter and replacement cover 4228 141 0502.
  • The replacement cover has no setting symbols and is universal within HS 45; old cover 4228 141 0500 remains for LD/BIS carburetors 4228 120 0600 and 0601. Do not confuse the illustrated marked production cover with the unmarked replacement.
  • Orange choke shutter 4140 141 3801 replaces black 4140 141 3800. Lever 4140 141 3700, push nut 9417 003 7512, filter 4140 124 2800 and prefilter 4228 124 1500 are unchanged. Old shutter and cover remain spares for older machines.
  • Old housing 4140 140 2800 is discontinued at introduction. The new bare housing is not separately available: the summary prints -*- rather than an order number; use complete kit 4228 140 2850. Introduction of the update package is in progress.
  • HS 45 only. Factory availability describes the 2001 bulletin, not present stock. No physical interchange or running adjustment was tested.

Source: TI 26/2001, p. 6 · TI 26/2001, p. 7 — Section 4.3, hinge drawing and 4.5 rows 7–14.

Part numbers (12)
  • 4228 140 2850 — Filter housing replacement kitBoth HS 45 generations · HS 45; configuration restrictions in this note
  • 4140 140 2800 — Filter housingPrevious · HS 45; configuration restrictions in this note
  • 4140 141 3700 — Choke leverUnchanged · HS 45; configuration restrictions in this note
  • 4140 141 3800 — Black choke shutterPrevious · HS 45; configuration restrictions in this note
  • 4140 141 3801 — Orange choke shutterNew · HS 45; configuration restrictions in this note
  • 9417 003 7512 — Push nut at chokeRetained · HS 45; configuration restrictions in this note
  • 4140 124 2800 — FilterUnchanged kit component · HS 45; configuration restrictions in this note
  • 4228 124 1500 — PrefilterUnchanged kit component · HS 45; configuration restrictions in this note
  • 4228 141 0500 — Filter coverPrevious LD-specific spare · HS 45; configuration restrictions in this note
  • 4228 141 0502 — Unmarked replacement filter coverUniversal within HS 45 · HS 45; configuration restrictions in this note
  • 4228 120 0600 — Carburetor C1Q-S49BOld-cover applicability · HS 45; configuration restrictions in this note
  • 4228 120 0601 — Carburetor C1Q-S54Old-cover applicability · HS 45; configuration restrictions in this note

Wrong number or missing part for the HS 45? Report a correction →