Stihl 4237 · Section H · 8 of 14 · 28 parts
Handle frame, Fuel tank
Fits HS 81 R, HS 81 RC, HS 81 T, HS 81 TC, HS 86 R, HS 86 T.
Historical fitment & changes (7) — includes parts and conditions not shown on this drawing.
Parts (28)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4237 791 4901 NLA | Handle frame | 1 |
| 2 | 4237 791 4900 | Handle frame | 1 |
| 3 | 4237 791 1700 | Handlebar | 1 |
| 4 | 9074 478 4425 | Pan head self-tapping screw IS-P6x19 | 2 |
| 5 | 4237 791 3101 | Spring | 4 |
| 6 | 0000 951 1100 | Screw IS-D5x20 | 4 |
| 7 | 9074 478 4420 | Pan head self-tapping screw IS-P6x18 | 10 |
| 8 | 4237 350 0452 | Fuel tank | 1 |
| 9 | 0000 350 5800 | Tank vent → replaced by 0000 350 5804 TI 41/2003 | 1 |
| 10 | 4237 350 1400 | Connector Fitment / change note → | 1 |
| 11 | not sold separately | Hose not available as a separate item | 1 |
| 12 | 0000 350 3503 | Pickup body | 1 |
| 13 | 0000 350 0532 | Filler cap | 1 |
| 14 | 9645 948 7734 | O-ring 25x3.5 | 1 |
| 15 | not sold separately | Hose 3.1x5.7x140 mm, R5 not available as a separate item | 1 |
| 16 | not sold separately | Hose 2.2x5.4x170 mm, R1 not available as a separate item | 1 |
| 17 | not sold separately | Hose 2.2x5.4x190 mm, R1 not available as a separate item | 1 |
| 18 | 4205 122 2500 | Hose clip | 1 |
| 19 | 0000 967 7224 | Warning pictogram Filler cap | 1 |
| 20 | 0000 967 3749 NLA | Warning pictogram Filler cap → replaced by 0000 967 3605 TI 19/2009 | 1 |
| 21 | 0000 967 3541 NLA | Instruction label | 1 |
| 22 | 0000 967 3500 NLA | Instruction label | 1 |
| 23 | 4237 792 9400 | Limit stop | 1 |
| 24 | 4237 792 1100 | Strut | 1 |
| 25 | 9074 478 4420 | Pan head self-tapping screw IS-P6x18 | 2 |
| 26 | 0000 967 4054 | Warning Spark arresting screen | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 937 5004 | Hose 3.1x5.7 mm x 1 m, R5 not illustratedoption | 1 |
| — | 0000 930 2802 | Hose 2.2x5.4 mm x 1 m, R1 not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · HS 81 R / HS 81 T / HS 86 R / HS 86 T
HS 81 / HS 86: replace removed fuel connector and O-ring
A used connector and seal must not be reused, even though the connector order number is unchanged.
- TI01/2007 explicitly names HS 81 R, HS 81 T, HS 86 R and HS 86 T, series 4237. The shared catalog sheet also lists RC/TC variants; that navigation grouping does not extend this assertion to those variants.
- After removal, replace used connector 4282 350 1400 with a NEW connector of the SAME number including its O-ring. Used connectors AND O-rings must not be reused: installation can crush the O-ring and destroy its sealing ability.
- O-ring 9645 948 7534, specified as A20x2.0 FPM70 in the summary, is no longer separately supplied according to this bulletin; it is included with connector 4282 350 1400. The unchanged connector number is not evidence that a used seal is acceptable.
- During assembly coat BOTH the O-ring and bead with Press Fluid 0781 957 9000; the illustration labels it Press Fluid OH 723. Always test the assembled tank for leaks using the companion test note.
- Retained 2007 source guidance, not present-day stock availability. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 1/2007, p. 1 · TI 1/2007, p. 2 — HS 81 / HS 86: replace removed fuel connector and O-ring.
Part numbers (3)
- 4282 350 1400 — Fuel connector including O-ringNew replacement required after removal · HS 81 R / HS 81 T / HS 86 R / HS 86 T; source restrictions apply
- 9645 948 7534 — O-ring A20x2.0 FPM70Included with connector; not separately supplied · HS 81 R / HS 81 T / HS 86 R / HS 86 T; source restrictions apply
- 0781 957 9000 — Press FluidCoat O-ring and bead · HS 81 R / HS 81 T / HS 86 R / HS 86 T; source restrictions apply
Service note · HS 81 R / HS 81 T / HS 86 R / HS 86 T
HS 81 / HS 86: fuel-tank leak test at 0.5 bar
After assembly, the tank must hold 0.5 bar for at least 20 seconds.
- Applies only to the four named HS 81 R/T and HS 86 R/T variants in TI01/2007, not every model sharing the catalog sheet. Always test after tank assembly; replacing the connector does not waive the test.
- Drain the fuel tank. Disconnect fuel supply hose (1), then install test connector (2) 0000 855 9200 to that hose. The numbered connector in this test illustration is NOT the permanent tank connector 4282 350 1400 from page 1.
- Connect pump 0000 850 1300 to the test connector as shown by the arrow. Supply 0.5 bar pressure to the fuel tank and maintain it for AT LEAST 20 seconds. This is a positive-pressure fuel-tank test, not a crankcase vacuum test or a running-engine procedure.
- If pressure drops, locate the leak: verify correct connector/O-ring fitting, inspect the fuel tank for damage and check the tank vent. No permitted pressure-drop allowance is printed; do not invent one.
- Retained 2007 source guidance, not present-day stock availability. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 1/2007, p. 1 · TI 1/2007, p. 2 — HS 81 / HS 86: fuel-tank leak test at 0.5 bar.
Part numbers (3)
- 0000 855 9200 — Fuel-hose test connectorConnect to drained tank supply hose · HS 81 R / HS 81 T / HS 86 R / HS 86 T; source restrictions apply
- 0000 850 1300 — Test pumpApply 0.5 bar for at least 20 seconds · HS 81 R / HS 81 T / HS 86 R / HS 86 T; source restrictions apply
- 4282 350 1400 — Permanent tank connectorDistinct from test connector · HS 81 R / HS 81 T / HS 86 R / HS 86 T; source restrictions apply
Service note · HS 81 R / HS 81 T / HS 86 R / HS 86 T
HS 81 / HS 86: 190 mm versus 170 mm return-hose configurations
Changing the carburetor OR flange requires the new return-hose length.
- Previous carburetor: fuel RETURN hose 7.48 in (190 mm), pushed FULLY onto its housing connector and secured by the existing clip (figure 442TI049). New carburetor: return hose 6.70 in (170 mm), fully installed on the BARBED connector (442TI050). These are return-hose lengths, not supply-hose lengths.
- Section 1.1 requires shortening to 170 mm when replacing the previous carburetor OR previous flange with its new version. It promises an illustrated installation supplement with the new parts; this is not proof that the separate supplement was recovered.
- Section 1.3 also expressly says disconnected fuel hoses MUST NOT BE REUSED because removal may over-extend them. Preserve that requirement alongside the shortening wording: shortening is a configuration dimension, not permission to refit an old disconnected hose.
- The new tank has the shorter return hose, but a 190 mm return hose is enclosed for installation in older machines. Choose the configuration by the carburetor/connector requirements; the tank’s retrofit permission does not erase the length distinction.
- Historical English-USA 2007 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 64/2007, p. 2 · TI 64/2007, p. 3 — HS 81 / HS 86: 190 mm versus 170 mm return-hose configurations.
No additional parts-table entry added.
Service note · HS 81 R / HS 81 T / HS 86 R / HS 86 T
HS 81 / HS 86: fuel-hose handling and assembly-fluid restriction
Disconnect and install hoses by hand; replace disconnected hoses.
- Fuel hoses must be disconnected and installed BY HAND to avoid damaging the barbed connector. Do not use sharp-edged pliers or screwdrivers on hoses and do not cut hoses open with a knife or similar implement.
- Disconnected hoses must ALWAYS be replaced with NEW hoses; possible over-extension prevents reuse. Fit new hoses DRY or with Press Fluid OH 723, order 0781 957 9000. If using it, coat the hose ends AND connectors before fitting.
- Press Fluid OH 723 forms a temporary lubricant film and evaporates shortly, allowing a tight fit. NEVER use FUEL, OIL OR GREASE as installation lubricant: they do not evaporate as required and may let the hose slip off.
- The separate instruction to gently pry the tank CONNECTOR by its tab does not authorize prying fuel HOSES off barbs.
- Historical English-USA 2007 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 64/2007, p. 2 — HS 81 / HS 86: fuel-hose handling and assembly-fluid restriction.
Part numbers (1)
- 0781 957 9000 — Press Fluid OH 723Allowed hose assembly aid · HS 81 R / HS 81 T / HS 86 R / HS 86 T; source restrictions apply
Service note · HS 81 R / HS 81 T / HS 86 R / HS 86 T
HS 81 / HS 86: new tank and complete connector supply
The separately supplied old fuel hose is discontinued; the new connector includes hose.
- New tank 4237 350 0450 replaces 4237 350 0405 and INCLUDES connector (summary item 7). New tank carries the shorter return hose and includes a separate 7.48 in (190 mm) return hose to permit installation in older machines; installation supplement is promised.
- Connector 4282 350 1400 becomes 4237 350 1400. New connector is supplied ONLY complete with fuel hose. Fuel hose 4237 358 0800 is no longer separately available as a spare part.
- Table remarks 1 and 2 on tank/connector mean previous versions no longer factory available and new versions also usable on older machines. These historical supply statements are not current inventory or permission to mix hose lengths without section 1.2.
- Historical English-USA 2007 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 64/2007, p. 3 · TI 64/2007, p. 7 — HS 81 / HS 86: new tank and complete connector supply.
Part numbers (5)
- 4237 350 0405 — Fuel tankPrevious · HS 81 R / HS 81 T / HS 86 R / HS 86 T; source restrictions apply
- 4237 350 0450 — Fuel tankNew; includes connector · HS 81 R / HS 81 T / HS 86 R / HS 86 T; source restrictions apply
- 4282 350 1400 — ConnectorPrevious · HS 81 R / HS 81 T / HS 86 R / HS 86 T; source restrictions apply
- 4237 350 1400 — ConnectorNew; complete with fuel hose · HS 81 R / HS 81 T / HS 86 R / HS 86 T; source restrictions apply
- 4237 358 0800 — Fuel hoseNo longer separately supplied · HS 81 R / HS 81 T / HS 86 R / HS 86 T; source restrictions apply
Service note · HS 81 R / HS 81 T / HS 86 R / HS 86 T
HS 81 / HS 86: connector removal, hose identity and keyed installation
The carburetor symbol marks the supply nipple, not the return nipple.
- Section 2.1.1: DRAIN and REMOVE tank (service manual referenced), disconnect hoses at carburetor (442TI052), gently pry the connector out using its TAB (442TI053). This tab operation is distinct from forbidden hose prying.
- Figure 442TI054: fit NEW return hose (1) and NEW supply hose (2) to new connector (3); the SUPPLY nipple bears a CARBURETOR SYMBOL. Coat connector O-ring AND bead with Press Fluid OH 723 before installation.
- Figure 442TI055: insert hose (1) into tank. Figure 442TI056: align connector tab with the tank GROOVE and press home with a suitable tool until it CLICKS. Reassemble remaining parts in reverse sequence. No tool dimension or force specification is given.
- The fuel tank MUST ALWAYS be tested for leaks after assembly. Referenced tank-removal details are not reproduced here; these illustrated connector steps do not constitute complete whole-machine service-manual acceptance.
- Historical English-USA 2007 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 64/2007, p. 3 · TI 64/2007, p. 4 — HS 81 / HS 86: connector removal, hose identity and keyed installation.
Part numbers (1)
- 0781 957 9000 — Press Fluid OH 723Connector O-ring and bead · HS 81 R / HS 81 T / HS 86 R / HS 86 T; source restrictions apply
Service note · HS 81 R / HS 81 T / HS 86 R / HS 86 T
HS 81 / HS 86: fuel-tank pressure test after assembly
The specified pressure is 0.5 bar for at least 20 seconds.
- Section 2.1.3: DRAIN tank; disconnect fuel SUPPLY hose (1); fit test connector (2), 0000 855 9200, to that hose (figure 442TI046). This test adapter is not the tank connector 4237 350 1400.
- Connect pump 0000 850 1300 to the test connector (442TI047); supply 0.5 bar PRESSURE to the FUEL TANK. Maintain this pressure for AT LEAST 20 seconds. This is not a crankcase test or a 0.5 bar vacuum specification.
- If pressure drops, locate the leak: verify connector/O-ring installation, inspect tank damage and check tank vent. No allowable pressure-decay tolerance is printed. No hardware test was performed in this review.
- Historical English-USA 2007 source, not present-day stock or approval for unlisted variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 64/2007, p. 4 — HS 81 / HS 86: fuel-tank pressure test after assembly.
Part numbers (2)
- 0000 855 9200 — Test connectorFuel-supply hose adapter · HS 81 R / HS 81 T / HS 86 R / HS 86 T; source restrictions apply
- 0000 850 1300 — PumpFuel-tank pressure test · HS 81 R / HS 81 T / HS 86 R / HS 86 T; source restrictions apply
Wrong number or missing part for the HS 81 R, HS 81 RC, HS 81 T, HS 81 TC, HS 86 R, HS 86 T? Report a correction →