Stihl 4238 · Section A · 1 of 13 · 22 parts
Crankcase
Fits TS 410, TS 420.
Historical fitment & changes (7) — includes parts and conditions not shown on this drawing.
Parts (22)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4238 020 2901 | Crankcase | 1 |
| 2 | 9503 003 0351 | Grooved ball bearing 15x36.3x11 | 2 |
| 3 | 0000 953 6606 | Stud | 3 |
| 4 | 9630 951 1696 | Oil seal 15x26x7 | 1 |
| 5 | 4238 020 2605 | Crankcase, fan side | 1 |
| 6 | 4238 020 2601 | Crankcase, fan side | 1 |
| 7 | 9640 003 1570 | Oil seal 15x24x7 | 1 |
| 8 | 0000 988 5211 | Connector | 1 |
| 9 | 0000 988 8600 | Sleeve | 2 |
| 10 | 9640 003 1560 | Oil seal 15x22x4 | 1 |
| 11 | 4238 448 1200 | Lead retainer | 1 |
| 12 | 4238 030 0400 | Crankshaft | 1 |
| 13 | 4238 029 0500 | Gasket | 1 |
| 14 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 4 |
| 15 | 4238 141 5400 | Hose | 1 |
| 16 | 4238 141 1800 | Sleeve | 1 |
| 17 | 4238 660 0400 | Belt tensioner | 1 |
| 18 | 4224 664 2100 | Clamping lever | 1 |
| 19 | 4224 664 4200 | Cover | 1 |
| 20 | 9075 478 4159 | Pan head self-tapping screw IS-D5x24 | 2 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4238 007 1003 | Set of gaskets option | 1 |
| — | 4238 007 1600 | Set of gaskets option | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · TS 410 / TS 420
TS 410 / TS 420: 2007 model introduction and scope
The TS 410 and TS 420 replace the TS 400 in the retained English-USA introduction.
- TI37/2007 identifies series 4238 and depicts both new cut-off machines on its cover. It describes two wheel-mount versions, 12 inches (300 mm) and 14 inches (350 mm); the introduction alone is not approval to swap wheel sizes or TS 400 components.
- The named design features are the long-life cyclone filter, low-emission stratified-scavenging TWO-CYCLE engine, spring anti-vibration system, compact/light construction, pictogram controls and ergonomic wrap-around handlebar. The reference to TS 700/800 concerns the established filter-system principle, not shared parts.
- Examples include construction, rental, landscaping, municipal/utilities, materials/steel trades and emergency/rescue work; free-hand cuts in construction materials, concrete, natural stone and concrete/steel/ductile-iron pipes, plus asphalt and prefabricated parts with a Cutquik cart. Actual wheel selection remains material- and version-specific.
- More-than-one-year average filter life, lowest vibration in the then-current STIHL range, conformity with then-present emission standards and readiness for future rules are HISTORICAL SOURCE CLAIMS, not measured results, guaranteed service life or present regulatory certification. No numerical emissions or vibration values are supplied on these introduction pages.
- Retained 2007 source guidance, not present-day stock availability. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 37/2007, p. 1 · TI 37/2007, p. 2 — TS 410 / TS 420: 2007 model introduction and scope.
No additional parts-table entry added.
Service note · TS 410 / TS 420
TS 410 / TS 420: intake, compression and scavenging sequence
Fresh air enters the transfer passages separately before mixture reaches the combustion chamber.
- Compression/intake: fuel-air mixture enters the crankcase while the piston-skirt control slot opens the fuel-free air port, admitting fresh air into the transfer passages; mixture already in the combustion chamber is compressed. Figure 000TI044 KN renumbers the slot as (1), fresh-air port (2), transfer ports (3); do not carry page 4 item (4) across as the same figure label.
- Expansion/crankcase compression: the spark plug ignites the charge shortly BEFORE top dead center. As the piston descends, fuel-free air in the transfer passages and fuel-air mixture in the crankcase are compressed. No numerical ignition advance is supplied.
- Exhaust/scavenging: descending piston opens the EXHAUST port FIRST, then the TRANSFER ports. Fuel-free air enters the combustion chamber ahead of the mixture and scavenges exhaust gas. Afterward fresh fuel-air mixture enters and mixes with the remaining fuel-free air.
- The paired cutaway views show different planes of the SAME cycle. The diagrams use distinct arrow patterns for fresh air, mixture and exhaust; they are not separate cylinders or measured flow rates. This is an operating-principle explanation, not a porting or ignition-adjustment procedure.
- Retained 2007 source guidance, not present-day stock availability. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 37/2007, p. 4 · TI 37/2007, p. 5 · TI 37/2007, p. 6 — TS 410 / TS 420: intake, compression and scavenging sequence.
No additional parts-table entry added.
Service note · TS 410 / TS 420
TS 410 / TS 420: four spring anti-vibration locations
The diagram identifies four different mounting locations, not four interchangeable springs.
- Section 1.4 describes spring elements reducing vibration transmission from engine to hands/arms. Figure 370TI003 KN labels: (1) clutch-side element between handlebar and crankcase; (2) element between support and crankcase; (3) element at bottom of crankcase; (4) element between tank housing and crankcase near the carburetor.
- The claims of smoother cutting and convenience are source descriptions, not measured attenuation. The figure supplies no spring rates, wear limits, tightening torques or order numbers; location numbers do not establish interchangeable parts.
- Retained 2007 source guidance, not present-day stock availability. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 37/2007, p. 8 — TS 410 / TS 420: four spring anti-vibration locations.
No additional parts-table entry added.
Service note · TS 410 / TS 420
TS 410 / TS 420: engine, spindle and starter specifications
Engine speeds and spindle speed are different measurements; wheel torque differs by model.
- Both models: stratified-scavenging two-cycle engine, displacement 4.07 cu in (66.7 cm³), bore 1.97 in (50 mm), stroke 1.34 in (34 mm), ISO 7293 power 4.3 hp at 9000 rpm and engine torque 2.8 lbf ft (3.8 Nm). These are historical specifications, not new bench measurements.
- Both models: idle 2500 rpm, clutch engagement 3800 rpm, ENGINE cutoff 10100 rpm; MAXIMUM SPINDLE speed to ANSI B175.4-2006 is separately printed as 5350 rpm. Do not use spindle speed as the engine adjustment limit or silently recalculate one printed value from another.
- Torque AT THE CUTTING WHEEL: TS 410 = 5.6 lbf ft (7.6 Nm); TS 420 = 5.9 lbf ft (8.0 Nm). These are operating torques, NOT fastener-tightening torques.
- Both starters are single-pawl systems. Starter-rope diameter × length is 0.177 in × 37.2 in (4.5 mm × 945 mm). Rounded inch/metric source pairs are preserved; this is not a complete starter replacement procedure.
- Retained English-USA 2007 source guidance, not present-day stock availability or proof for later variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 37/2007, p. 10 — engine, spindle and starter specifications.
No additional parts-table entry added.
Service note · TS 410 / TS 420
TS 410 / TS 420: five new service tools and their distinct functions
The original illustration identifies all five tools, including two labels missed by body extraction.
- Figure 370TI005 KN and its table identify (1) sleeve 5910 893 1707 for fitting HOOKLESS piston snap rings; (2) press sleeve 4238 893 2400 for pressing in an oil seal; (3) ring 4238 893 7000 for tensioning piston rings.
- Item (4) clamping plate 4238 890 2100 mounts the cut-off machine on the assembly stand. Item (5) flange 4238 890 1200 is for leakage testing. The scan shows both lower illustrations and their labels, even though body extraction retains only top labels 1–3.
- The snap-ring sleeve drawing is marked 10; that marking is NOT a 10 mm dimension or the later washer marking 21. The flange picture shows a connection, but gives no test pressure, test duration or universal adapter approval.
- Existing special tools are referred to the TS 410/420 Service Manual in section 5.2. These five drawings are an identification/function roster, not scale manufacturing drawings or complete setup instructions.
- Retained English-USA 2007 source guidance, not present-day stock availability or proof for later variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 37/2007, p. 13 — five new service tools and their distinct functions.
Part numbers (5)
- 5910 893 1707 — SleeveFit hookless piston snap rings · TS 410 / TS 420; source restrictions apply
- 4238 893 2400 — Press sleevePress in oil seal · TS 410 / TS 420; source restrictions apply
- 4238 893 7000 — RingTension piston rings · TS 410 / TS 420; source restrictions apply
- 4238 890 2100 — Clamping plateMount on assembly stand · TS 410 / TS 420; source restrictions apply
- 4238 890 1200 — FlangeLeakage testing · TS 410 / TS 420; source restrictions apply
Service note · TS 410 / TS 420
TS 410 / TS 420: service-tool washer: three holes marked 21
The original template gives three separate hole locations, not a common bolt circle.
- Section 5.2.1 concerns washer 5910 893 2102 in service tool 5910 007 2200. Future factory-supplied tools include the modified washer with THREE ADDITIONAL holes of diameter 7/32 inch (5.5 mm) for TS 410/420. Existing washers lacking those holes may be reworked according to the source template.
- The source says COPY the drawn-to-scale template, CUT IT OUT and place it on the washer to mark the new holes. Stamp 21 on the UPPER SIDE alongside EACH new hole. A browser screenshot or resized scan is NOT automatically a true-scale physical template; verify scale against the printed dimensions before using a copy.
- Figure 370TI010 KN: relative to the intersecting central axes AS DRAWN, the upper-left new hole is 38.2 left and 21.1 above; the right new hole is 42.2 right and 11.2 above; the lower-left new hole is 17.3 left and 34.4 below. The top notch fixes the displayed orientation. These six dimension values are printed WITHOUT an explicit unit label on the diagram; the prose separately identifies hole diameter in inch/mm.
- The three bold outlined holes carry 21 labels; the many faint holes are pre-existing geometry, not additional drilling targets. Do not treat 21 as a diameter, infer a common pitch circle, mirror the pattern or label these values as a verified CNC program. Washer thickness, tolerances and machining setup are not given.
- Retained English-USA 2007 source guidance, not present-day stock availability or proof for later variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 37/2007, p. 14 — service-tool washer: three holes marked 21.
Part numbers (2)
- 5910 893 2102 — Service-tool washerThree added holes, each marked 21 · TS 410 / TS 420; source restrictions apply
- 5910 007 2200 — Service toolIncludes modified washer in future supply · TS 410 / TS 420; source restrictions apply
Service note · TS 410 / TS 420
TS 410 / TS 420: repair allowances: included leak, fuel and circuit tests
The included tests and failure-cause repair are part of the printed allowances.
- The same trained-personnel, properly-equipped-shop scope and MINUTES apply. Rows 11–15: (11) replace crankcase/gasket or reseal crankcase, INCLUDING air-leak test = 160; (12) crankshaft main bearing(s), INCLUDING air-leak test = 170; (13) crankshaft seal(s), INCLUDING air-leak test = 70; (14) engine air-leak test alone = 30; (15) cylinder and/or piston, INCLUDING air-leak test AND repair of components causing failure = 90.
- Rows 16–20: (16) ignition module or flywheel replacement, INCLUDING stop-circuit test = 25; (17) fuel-tank line, vent line or pickup-body replacement = 40; (18) intake/transfer-port manifold or intake-flange replacement = 35; (19) carburetor repair/replacement, INCLUDING fuel-system testing = 45; (20) rewind-starter repair/replacement = 15.
- An included test must not be silently dropped or automatically charged twice by summing a standalone test row. These allowances do not supply leakage pressures, test durations, electrical limits, tightening torques or a full diagnostic sequence.
- Retained English-USA 2007 source guidance, not present-day stock availability or proof for later variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 37/2007, p. 16 — repair allowances: included leak, fuel and circuit tests.
No additional parts-table entry added.
Wrong number or missing part for the TS 410, TS 420? Report a correction →