← TS 410, TS 420

Stihl 4238 · Section B · 2 of 13 · 28 parts

Cylinder, Muffler

Fits TS 410, TS 420.

Parts diagrams →

Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314141516171819220212223232425334456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (28)

PosPart numberDescriptionQty
1 4238 020 1202 Cylinder with piston Ø 50 mm 1
2 4238 030 2003 Piston Ø 50 mm 1
3 1128 034 3000 Piston ring Ø 50x1.2 mm 2
4 9463 650 1000 Snap ring 10 2
5 4238 034 1500 Piston pin 10x6x32 1
6 9512 003 2344 Needle cage 10x14x13 1
7 4238 029 2300 Cylinder gasket 1
8 9022 371 1073 Spline screw IS-M5x32 4
9 4238 020 9400 Decompression valve 1
10 1110 400 7005 Spark plug Bosch WSR 6 F 1
10 0000 400 7000 Spark plug NGK BPMR7A 1
11 4238 140 0610 Muffler 1
12 4238 140 0611 Muffler 1
13 4238 149 0600 Muffler gasket 1
14 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 3
15 4238 141 9000 Screen 1
16 9039 448 0656 Self-tapping screw M4x9.6 1
17 4238 141 3200 Cooling plate 1
18 4238 080 0900 Air guide shroud 1
19 9991 003 5087 Sleeve 7.5x6.8 1
20 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 2
21 4238 141 2203 Manifold 1
22 4238 141 2202 Manifold 1
23 9771 021 2536 Hose clamp 30x5 2
24 4238 140 2200 Flange 1
25 0000 141 8600 Impulse hose 1
Not numbered on the diagram — assemblies, kits and options
— 4238 007 1003 Set of gaskets option 1
— 4238 007 1600 Set of gaskets option 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · TS 410 / TS 420

TS 410 / TS 420: separate fuel-air and fresh-air ports

A piston-skirt slot connects the fresh-air ports to the transfer ports at the appropriate phase.

  • A fuel-free air cushion precedes the unburned mixture during scavenging. It enters the combustion chamber through the transfer ports first and pushes exhaust gas toward the exhaust port, reducing fresh-mixture loss to the exhaust and fuel consumption according to the source.
  • Figure 000TI043 KN labels fuel-air port (1), separate fresh-air ports (2), transfer ports (3), and integrally molded piston-skirt control slot (4). The slot opens and closes the connection between fresh-air and transfer ports.
  • These are TWO-CYCLE stratified-scavenging flow paths, not separate oil injection, a four-stroke valve train or permission to modify port timing. The page provides no port dimensions, timing angles or measured emissions reduction.
  • Retained 2007 source guidance, not present-day stock availability. No numeric serial cutoff is supplied. No physical interchange test was performed.

Source: TI 37/2007, p. 4 — TS 410 / TS 420: separate fuel-air and fresh-air ports.

No additional parts-table entry added.

Service note · TS 410 / TS 420

TS 410 / TS 420: intake, compression and scavenging sequence

Fresh air enters the transfer passages separately before mixture reaches the combustion chamber.

  • Compression/intake: fuel-air mixture enters the crankcase while the piston-skirt control slot opens the fuel-free air port, admitting fresh air into the transfer passages; mixture already in the combustion chamber is compressed. Figure 000TI044 KN renumbers the slot as (1), fresh-air port (2), transfer ports (3); do not carry page 4 item (4) across as the same figure label.
  • Expansion/crankcase compression: the spark plug ignites the charge shortly BEFORE top dead center. As the piston descends, fuel-free air in the transfer passages and fuel-air mixture in the crankcase are compressed. No numerical ignition advance is supplied.
  • Exhaust/scavenging: descending piston opens the EXHAUST port FIRST, then the TRANSFER ports. Fuel-free air enters the combustion chamber ahead of the mixture and scavenges exhaust gas. Afterward fresh fuel-air mixture enters and mixes with the remaining fuel-free air.
  • The paired cutaway views show different planes of the SAME cycle. The diagrams use distinct arrow patterns for fresh air, mixture and exhaust; they are not separate cylinders or measured flow rates. This is an operating-principle explanation, not a porting or ignition-adjustment procedure.
  • Retained 2007 source guidance, not present-day stock availability. No numeric serial cutoff is supplied. No physical interchange test was performed.

Source: TI 37/2007, p. 4 · TI 37/2007, p. 5 · TI 37/2007, p. 6 — TS 410 / TS 420: intake, compression and scavenging sequence.

No additional parts-table entry added.

Service note · TS 410 / TS 420

TS 410 / TS 420: five new service tools and their distinct functions

The original illustration identifies all five tools, including two labels missed by body extraction.

  • Figure 370TI005 KN and its table identify (1) sleeve 5910 893 1707 for fitting HOOKLESS piston snap rings; (2) press sleeve 4238 893 2400 for pressing in an oil seal; (3) ring 4238 893 7000 for tensioning piston rings.
  • Item (4) clamping plate 4238 890 2100 mounts the cut-off machine on the assembly stand. Item (5) flange 4238 890 1200 is for leakage testing. The scan shows both lower illustrations and their labels, even though body extraction retains only top labels 1–3.
  • The snap-ring sleeve drawing is marked 10; that marking is NOT a 10 mm dimension or the later washer marking 21. The flange picture shows a connection, but gives no test pressure, test duration or universal adapter approval.
  • Existing special tools are referred to the TS 410/420 Service Manual in section 5.2. These five drawings are an identification/function roster, not scale manufacturing drawings or complete setup instructions.
  • Retained English-USA 2007 source guidance, not present-day stock availability or proof for later variants. No numeric serial cutoff is supplied. No physical interchange test was performed.

Source: TI 37/2007, p. 13 — five new service tools and their distinct functions.

Part numbers (5)
  • 5910 893 1707 — SleeveFit hookless piston snap rings · TS 410 / TS 420; source restrictions apply
  • 4238 893 2400 — Press sleevePress in oil seal · TS 410 / TS 420; source restrictions apply
  • 4238 893 7000 — RingTension piston rings · TS 410 / TS 420; source restrictions apply
  • 4238 890 2100 — Clamping plateMount on assembly stand · TS 410 / TS 420; source restrictions apply
  • 4238 890 1200 — FlangeLeakage testing · TS 410 / TS 420; source restrictions apply

Service note · TS 410 / TS 420

TS 410 / TS 420: repair allowances: included leak, fuel and circuit tests

The included tests and failure-cause repair are part of the printed allowances.

  • The same trained-personnel, properly-equipped-shop scope and MINUTES apply. Rows 11–15: (11) replace crankcase/gasket or reseal crankcase, INCLUDING air-leak test = 160; (12) crankshaft main bearing(s), INCLUDING air-leak test = 170; (13) crankshaft seal(s), INCLUDING air-leak test = 70; (14) engine air-leak test alone = 30; (15) cylinder and/or piston, INCLUDING air-leak test AND repair of components causing failure = 90.
  • Rows 16–20: (16) ignition module or flywheel replacement, INCLUDING stop-circuit test = 25; (17) fuel-tank line, vent line or pickup-body replacement = 40; (18) intake/transfer-port manifold or intake-flange replacement = 35; (19) carburetor repair/replacement, INCLUDING fuel-system testing = 45; (20) rewind-starter repair/replacement = 15.
  • An included test must not be silently dropped or automatically charged twice by summing a standalone test row. These allowances do not supply leakage pressures, test durations, electrical limits, tightening torques or a full diagnostic sequence.
  • Retained English-USA 2007 source guidance, not present-day stock availability or proof for later variants. No numeric serial cutoff is supplied. No physical interchange test was performed.

Source: TI 37/2007, p. 16 — repair allowances: included leak, fuel and circuit tests.

No additional parts-table entry added.

Wrong number or missing part for the TS 410, TS 420? Report a correction →