Stihl 4238 · Section C · 3 of 13 · 30 parts
Clutch, Handlebar
Fits TS 410, TS 420.
Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.
Parts (30)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1125 162 3202 | Carrier | 1 |
| 2 | 1128 162 0806 | Clutch shoe | 3 |
| 3 | 1128 162 3000 | Retainer | 3 |
| 4 | 0000 997 5510 | Tension spring | 3 |
| 5 | 4238 195 0600 | Starter cup | 1 |
| 6 | 0000 955 0802 | Collar nut M8x1 | 1 |
| 7 | 0000 036 0200 | Ring | 1 |
| 8 | 4238 760 8500 | Poly V-belt pulley | 1 |
| 9 | 9503 003 5136 | Grooved ball bearing 6001-2RS | 1 |
| 10 | 9456 621 3100 | Circlip 28x1.2 | 1 |
| 11 | 9490 000 7901 | Poly V-belt, ribbed 5PJ740LB | 1 |
| 12 | 9490 000 7900 | Poly V-belt, ribbed 5PJ801LB | 1 |
| 13 | 4238 791 1700 | Handlebar | 1 |
| 14 | 4238 790 8301 | AV-Spring | 1 |
| 15 | 9074 478 4425 | Pan head self-tapping screw IS-P6x19 | 4 |
| 16 | 4238 791 0910 | Clamp | 1 |
| 17 | 9074 478 4705 | Pan head self-tapping screw IS-P6x40 | 2 |
| 18 | 9074 478 4545 | Pan head self-tapping screw IS-P6x26.5 | 2 |
| 19 | 4238 790 8302 | AV-Spring | 1 |
| 20 | 4238 791 1900 | Handlebar support | 1 |
| 21 | 4238 791 0900 | Clamp | 1 |
| 22 | 9075 478 4190 | Pan head self-tapping screw IS-D5x45 | 1 |
| 23 | 4238 791 0905 | Clamp | 1 |
| 24 | 4238 791 7601 | Support | 1 |
| 25 | 4205 790 9300 | Rubber buffer | 2 |
| 26 | 0000 951 1100 | Screw IS-D5x20 | 2 |
| 27 | 9074 478 4706 | Pan head self-tapping screw IS-P6x50 | 2 |
| 28 | 4238 790 8304 | AV-Spring | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4238 160 2002 | Clutch | 1 |
| — | 4238 790 7600 | Support | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · TS 410 / TS 420
TS 410 / TS 420: four spring anti-vibration locations
The diagram identifies four different mounting locations, not four interchangeable springs.
- Section 1.4 describes spring elements reducing vibration transmission from engine to hands/arms. Figure 370TI003 KN labels: (1) clutch-side element between handlebar and crankcase; (2) element between support and crankcase; (3) element at bottom of crankcase; (4) element between tank housing and crankcase near the carburetor.
- The claims of smoother cutting and convenience are source descriptions, not measured attenuation. The figure supplies no spring rates, wear limits, tightening torques or order numbers; location numbers do not establish interchangeable parts.
- Retained 2007 source guidance, not present-day stock availability. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 37/2007, p. 8 — TS 410 / TS 420: four spring anti-vibration locations.
No additional parts-table entry added.
Service note · TS 410 / TS 420
TS 410 / TS 420: model-specific belts, ratios and machine dimensions
The two belt lengths and wheel-equipped dimensions must stay attached to their model.
- TS 410 ribbed poly belt: 0.46 in × 29.1 in (11.7 mm × 740 mm), designation 5PJ 740 LB, transmission ratio 2.00. TS 420: 0.46 in × 31.5 in (11.7 mm × 801 mm), 5PJ 801 LB, ratio 2.11. These are belt designations, not STIHL order numbers or proof of interchange.
- Weight WITHOUT cutting wheel and WITHOUT fuel: TS 410 = 20.7 lb (9.4 kg); TS 420 = 21.2 lb (9.6 kg). This is not ready-to-cut operating weight.
- Length INCLUDING cutting wheel: TS 410 = 26.57 in (675 mm); TS 420 = 28.54 in (725 mm). Height UP TO GUARD: 14.76 in (375 mm) versus 16.14 in (410 mm). Width INCLUDING HANDLEBAR is 11.81 in (300 mm) for both.
- The table does not specify belt tension, wear limits or a conversion kit between the two wheel sizes. Source inch/metric pairs are retained without using rounded values as manufacturing tolerances.
- Retained English-USA 2007 source guidance, not present-day stock availability or proof for later variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 37/2007, p. 11 — model-specific belts, ratios and machine dimensions.
No additional parts-table entry added.
Service note · TS 410 / TS 420
TS 410 / TS 420: repair allowances: wheel drive and handles
Published minutes apply to trained personnel and properly equipped shops, not every owner repair.
- Section 7.4 applies to TRAINED AND QUALIFIED personnel and PROPERLY EQUIPPED repair shops; values are MINUTES. They are historical labor allowances, not measured performance, required service intervals or abbreviated repair procedures.
- Rows 1–5: (1) replace engine or shortblock = DASH, not zero; (2) wheel guard = 20; (3) wheel-bearing bracket assembly = 25; (4) belt pulley on wheel arbor = 15; (5) wheel-arbor shaft = 15.
- Rows 6–10: (6) arbor-shaft bearing = 25; (7) belt pulley on clutch end = 25; (8) drive belt = 15; (9) front handlebar = 15; (10) cast arm from engine to wheel = 25. All are replacement activities for TS 410/420.
- The blank/dash engine allowance does not mean a complete engine replacement takes no labor. Allowances for combined jobs are not specified and must not be automatically summed.
- Retained English-USA 2007 source guidance, not present-day stock availability or proof for later variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 37/2007, p. 16 — repair allowances: wheel drive and handles.
No additional parts-table entry added.
Service note · TS 410 / TS 420
TS 410 / TS 420: repair allowances: remaining jobs and no-labor rows
Handling allowance, miscellaneous repairs and no labor have different meanings.
- For trained/qualified personnel in properly equipped shops, in MINUTES: (21) repair/replace clutch, shoes or springs = 20; (22) replace rear handle frame or handle housing = 45; (23) replace muffler = 25; (24) replace air filter or filter housing = 15; (25) repair/replace stop switch INCLUDING circuit testing = 35.
- Row 40 miscellaneous/unlisted repairs = 15. Row 45 HANDLING ALLOWANCE ONLY — NO LABOR = 10. Row 50 NO LABOR = 0. The 10-minute handling allowance is not a repair labor estimate, and the explicit zero in row 50 is not the dash in engine-replacement row 1.
- The table has rows 1–25, 40, 45 and 50: 28 listed activities, NOT 50 rows or 50 completed repairs. The numbering gaps do not imply lost pages. Footer identifies 2007 Technical Documentation D1/MTK-fr; no prices or warranty approval are supplied.
- Retained English-USA 2007 source guidance, not present-day stock availability or proof for later variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 37/2007, p. 16 — repair allowances: remaining jobs and no-labor rows.
No additional parts-table entry added.
Wrong number or missing part for the TS 410, TS 420? Report a correction →