Stihl 4238 · Section E · 5 of 13 · 37 parts
Tank housing
Fits TS 410, TS 420.
Historical fitment & changes (7) — includes parts and conditions not shown on this drawing.
Parts (37)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4238 350 0814 | Tank housing | 1 |
| 2 | 4238 350 0850 | Tank housing Fitment / change note → | 1 |
| 3 | 9443 825 7131 | Hollow rivet 7.5x1x9.1 | 3 |
| 4 | 4238 350 5800 | Tank vent | 1 |
| 5 | 4223 353 9201 | Grommet | 1 |
| 6 | 0000 350 0514 | Filler cap | 1 |
| 7 | 9645 948 2471 | O-ring 23x3 | 1 |
| 8 | 0000 350 0905 | Rope | 1 |
| 9 | 4238 352 8201 | Clamp | 1 |
| 10 | 4238 350 6201 | Fuel pump | 1 |
| 11 | not sold separately | Hose 3.1x5.7x127 mm, R3 not available as a separate item | 1 |
| 12 | not sold separately | Hose 3.1x5.7x94 mm, R3 not available as a separate item | 1 |
| 13 | not sold separately | Hose 3.1x5.7x102 mm, R3 not available as a separate item | 1 |
| 14 | not sold separately | Hose 3.1x5.7x70 mm, R3 not available as a separate item | 1 |
| 15 | 4238 353 2701 | Connector | 1 |
| 16 | 4238 353 9200 | Grommet | 1 |
| 17 | 4238 358 7700 | Hose | 1 |
| 18 | 4238 790 8300 | AV-Spring | 1 |
| 19 | 9074 477 4130 | Pan head self-tapping screw IS-P5x16 | 1 |
| 20 | 9074 478 4425 | Pan head self-tapping screw IS-P6x19 | 2 |
| 21 | 4238 354 0100 | Support foot | 1 |
| 22 | 0000 350 3506 | Pickup body | 1 |
| 23 | 4238 140 1000 | Filter cover Fitment / change note → | 1 |
| 24 | 0000 951 1109 | Screw IS-M5x20 Fitment / change note → | 4 |
| 25 | 4238 141 6300 | Air baffle | 1 |
| 26 | 4238 141 6301 | Air baffle | 1 |
| 27 | 4238 440 1101 | Lead | 1 |
| 29 | 4238 121 6100 | Choke lever | 1 |
| 30 | 4238 185 1500 | Choke rod | 1 |
| 31 | 9022 341 1220 | Spline screw IS-M5x48 | 3 |
| 32 | 4238 129 0900 | Gasket | 1 |
| 33 | 4238 120 0600 | Carburetor C1Q-S118C | 1 |
| 34 | 4238 120 0601 | Carburetor C1Q-S167A | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 930 2803 | Hose 3.1x5.7 mm x 1 m, R3 not illustratedoption | 1 |
| — | 0712 923 8004 | Hose 3.1x5.7 mm x 10 m, R3 not illustratedoption | 1 |
| — | 4238 007 1003 | Set of gaskets option | 1 |
| — | 4238 007 1600 | Set of gaskets option | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · TS 410 / TS 420
TS 410 / TS 420: cyclone air path and no-cleaning filter rule
Replace the filter at the stated service trigger; do not clean its element.
- Section 1.1 says remove the filter cover and replace the air filter only if there is a noticeable power loss OR more than a year of extended use has elapsed since the last change. DO NOT CLEAN the air filter: the source warns of filter-element damage and consequential engine damage. The average-life claim does not override the power-loss trigger.
- Contaminated air enters tank housing (1); its integrated cyclone spins heavier/larger particles down into the tank housing. The dirty-air stream passes through molded hose (3), to fan-side crankcase half (2), then out of the machine.
- Precleaned air takes the separate route through air filter (4), auxiliary filter (5), then carburetor (6). The illustration separates the tank housing into components only to explain flow; it is not an instruction to split the welded housing.
- Figure item numbers are not filter order numbers. This section supplies neither a filter-cleaning method nor a separate auxiliary-filter service interval, and none is inferred.
- Retained 2007 source guidance, not present-day stock availability. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 37/2007, p. 2 · TI 37/2007, p. 3 · TI 37/2007, p. 9 — TS 410 / TS 420: cyclone air path and no-cleaning filter rule.
No additional parts-table entry added.
Service note · TS 410 / TS 420
TS 410 / TS 420: four spring anti-vibration locations
The diagram identifies four different mounting locations, not four interchangeable springs.
- Section 1.4 describes spring elements reducing vibration transmission from engine to hands/arms. Figure 370TI003 KN labels: (1) clutch-side element between handlebar and crankcase; (2) element between support and crankcase; (3) element at bottom of crankcase; (4) element between tank housing and crankcase near the carburetor.
- The claims of smoother cutting and convenience are source descriptions, not measured attenuation. The figure supplies no spring rates, wear limits, tightening torques or order numbers; location numbers do not establish interchangeable parts.
- Retained 2007 source guidance, not present-day stock availability. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 37/2007, p. 8 — TS 410 / TS 420: four spring anti-vibration locations.
No additional parts-table entry added.
Service note · TS 410 / TS 420
TS 410 / TS 420: four-piece welded multifunction tank housing
The exploded illustration explains construction, not service separation of the welded housing.
- Section 1.6 states that FOUR individual parts are welded together to form the tank housing; high rigidity and low weight are design claims. Figure 370TI004 KN shows the constituent shapes, not a repair disassembly sequence.
- Integrated functions are cyclone pre-separation, filter base, fuel hose, tank vent and fuel overflow. The text does not say that the entire airflow cavity contains fuel or authorize sealing off cyclone passages.
- No weld-repair method, separable housing joint, plastic material specification or pressure-test value is given here. Do not reuse the unrelated HS 81/86 tank test from TI01/2007 for this TS housing.
- Retained 2007 source guidance, not present-day stock availability. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 37/2007, p. 3 · TI 37/2007, p. 9 — TS 410 / TS 420: four-piece welded multifunction tank housing.
No additional parts-table entry added.
Service note · TS 410 / TS 420
TS 410 / TS 420: fuel capacity and limiter-dependent carburetor settings
Standard capped settings and uncapped basic settings must not be merged.
- The mixture-lubricated engine uses gasoline and engine oil; section 2.2.1 explicitly refers to the INSTRUCTION MANUAL for the mixture. No numerical mixing ratio is printed here. Tank capacity is 26.0 oz (0.77 l).
- The carburetor is an all-position diaphragm type with booster pump. STANDARD setting WITH high-speed limiter cap: L = 1 turn open; H = carefully turn COUNTERCLOCKWISE as far as the stop, MAXIMUM 3/4 turn. The H entry is not an instruction to turn 3/4 from a fully seated uncapped screw.
- BASIC setting WITHOUT limiter cap: L = 1 turn open; H = 1.5 turns open. The two H conditions are different configurations, not interchangeable alternatives or permission to remove the limiter.
- This table gives no limiter-removal/refitting sequence, warm-engine tuning sequence or altitude compensation. The page 15 kit is explicitly for C1Q-S118; navigation through the later shared C1Q-S118C / C1Q-167A catalog sheet does NOT establish these settings or kit compatibility for all later carburetors.
- Retained English-USA 2007 source guidance, not present-day stock availability or proof for later variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 37/2007, p. 10 · TI 37/2007, p. 11 · TI 37/2007, p. 15 — fuel capacity and limiter-dependent carburetor settings.
No additional parts-table entry added.
Service note · TS 410 / TS 420
TS 410 / TS 420: manual references, catalog edition and serial location
The serial number is underneath the machine on the tank housing; no serial range is given.
- Section 6 says spare-parts lists will be available at market launch; the ORIGINAL SCAN names STIHL service catalogue (CD-ROM), starting with edition 03/2007. That catalogue name is absent from extracted body text. This is a historical inclusion statement, not proof that any particular installation has that edition.
- Section 7 requires applicable national safety regulations and the instruction-manual safety instructions if starting the machine during service. Sections 7.1/7.2 refer tightening torques and servicing/repair to the TS 410/420 SERVICE MANUAL. No fastening torques or complete repair procedures are printed here.
- Section 7.3 and figure 370TI007 KN locate the serial number on the TANK HOUSING, UNDERNEATH the machine, at the illustrated # pointer. The # is a location marker, not part of a serial value. No numeric serial cutoff, production range or decoding method is supplied.
- The instruction-manual fuel ratio and safety instructions, existing-tool list and service-manual repair/torque details remain explicitly REFERENCED content, not recovered content in this TI. This review closes the TI’s reference statements only; whole-manual acquisition and acceptance remain separate.
- Retained English-USA 2007 source guidance, not present-day stock availability or proof for later variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 37/2007, p. 10 · TI 37/2007, p. 13 · TI 37/2007, p. 15 — manual references, catalog edition and serial location.
No additional parts-table entry added.
Service note · TS 410 / TS 420
TS 410 / TS 420: new tank housing requires new cover and screws
The tank/filter joint has an explicit serial introduction, unlike the carburetor stages.
- Tank housing 4238 350 0813 becomes 4238 350 0850, with modified threaded inserts for the filter cover (arrows in 370TI048). New tank housing INCLUDES improved filter cover and new screws; summary item 13 includes items 14,15,17 and refers other unchanged parts to the spare-parts list.
- Section 2 states modifications introduced at serial #170 073 909 for the tank housing/filter cover/screw connection. The summary also says introduction CONTINUOUSLY. Preserve BOTH source statements; do not extend this section-specific serial to the carburetor stages or the separately described fan cover, and do not invent a universal early/late matcher.
- Old tank housing is no longer available; new housing can also be used on older machines. Whenever a NEW TANK HOUSING is installed, ALWAYS fasten the NEW FILTER COVER with the NEW SCREWS. Retained old bushings or an unchanged filter-cover number do not waive this requirement.
- Historical English 2009 source for TS 410 and TS 420, series 4238; supply statements are not present-day stock claims. No physical interchange test was performed.
Source: TI 22/2009, p. 4 · TI 22/2009, p. 5 · TI 22/2009, p. 7 — new tank housing requires new cover and screws.
Part numbers (4)
- 4238 350 0813 — Tank housingPrevious · TS 410 / TS 420; source revision and pairing restrictions apply
- 4238 350 0850 — Tank housing with improved insertsNew; includes new cover/screws · TS 410 / TS 420; source revision and pairing restrictions apply
- 4238 140 1000 — Filter coverNew revision required with new housing · TS 410 / TS 420; source revision and pairing restrictions apply
- 0000 951 1109 — New filter-cover screwRequired with new housing · TS 410 / TS 420; source revision and pairing restrictions apply
Service note · TS 410 / TS 420
TS 410 / TS 420: C-index filter cover retains its number but changes bushings
New lead-in screws also change strength class; integrated bushings are not spares.
- Filter cover 4238 140 1000 retains its number. Figure 370TI049 identifies the NEW cover as index C OR HIGHER, with permanently integrated knurled bushings replacing old separate bushing 0000 963 0809. New knurled bushings are NOT available as spare parts; old bushing remains available for previous covers.
- FOUR previous IS-M5x20-12.9 screws 9022 371 1020 are replaced by IS-M5x20-10.9 screws 0000 951 1109. New screws have a LEAD-IN (drawing 6) to simplify mounting. Preserve both 20 mm length and changed 12.9-to-10.9 class; the same M5 size does not make an arbitrary screw equivalent. No tightening torque is given.
- Previous screw remains available FOR OTHER APPLICATIONS. Summary row 14 marks the previous cover version discontinued and the new version usable on older machines, despite the unchanged order number; row 17 permits new screws on older machines. New tank housing still requires BOTH new cover AND new screws. No separate new bushing number is invented from the -*- summary cell.
- Historical English 2009 source for TS 410 and TS 420, series 4238; supply statements are not present-day stock claims. No physical interchange test was performed.
Source: TI 22/2009, p. 5 · TI 22/2009, p. 7 — C-index filter cover retains its number but changes bushings.
Part numbers (4)
- 4238 140 1000 — Filter coverSame number; C-index or higher new version · TS 410 / TS 420; source revision and pairing restrictions apply
- 0000 963 0809 — Separate bushingRetained for previous cover · TS 410 / TS 420; source revision and pairing restrictions apply
- 9022 371 1020 — IS-M5x20-12.9 screwPrevious; other-application supply · TS 410 / TS 420; source revision and pairing restrictions apply
- 0000 951 1109 — IS-M5x20-10.9 screw with lead-inNew; four screws · TS 410 / TS 420; source revision and pairing restrictions apply
Wrong number or missing part for the TS 410, TS 420? Report a correction →