Stihl 4238 · Section J · 9 of 13 · 71 parts
Connector, Guard
Fits TS 410, TS 420.
Historical fitment & changes (4) — includes parts and conditions not shown on this drawing.
Parts (71)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4238 701 0203 | Cast arm | 1 |
| 2 | 4238 700 8105 | Guard Ø 300 mm / 12'' | 1 |
| 3 | 4238 700 8102 | Guard Ø 300 mm / 12'' | 1 |
| 4 | 4238 706 0400 | Stiffener | 2 |
| 5 | 4238 691 0200 | Limit stop | 1 |
| 6 | 9074 478 3025 | Pan head self-tapping screw IS-P4x16 | 1 |
| 7 | 4224 691 0100 | Stop pin | 1 |
| 8 | 9503 003 6440 | Grooved ball bearing 6201-2RS → replaced by 9503 003 6420 TI 5/1994 | 2 |
| 9 | 0000 961 1206 | Ring | 1 |
| 10 | 9456 621 3600 | Circlip 32x1.2 | 2 |
| 11 | 4224 704 0502 | Shaft | 1 |
| 12 | 4201 706 9202 | Washer | 2 |
| 13 | 4224 706 8802 | Rubber ring | 1 |
| 14 | 4224 706 8801 | Rubber ring | 1 |
| 15 | 4205 706 2903 | Flange | 1 |
| 16 | 4238 710 9500 | Adjusting screw | 4 |
| 17 | 0000 670 0207 | Banjo bolt | 1 |
| 18 | 9645 948 0340 | O-ring 6x1.5 | 2 |
| 19 | 9041 216 0630 | Pan head screw M4x8 | 2 |
| 20 | 0000 679 2000 | Gasket | 1 |
| 21 | 4224 708 8300 | Square nut | 2 |
| 22 | 0000 670 0206 | Banjo bolt | 1 |
| 23 | 4238 677 8202 | Connector | 1 |
| 24 | 9771 021 0921 | Hose clip 10/7 | 2 |
| 25 | 4238 677 8200 | Connector | 1 |
| 26 | 4238 708 8200 | Bracket | 1 |
| 27 | 4201 700 4500 | Shut-off cock 1/4" | 1 |
| 28 | 0000 954 1701 | Sealing ring | 1 |
| 30 | 9645 945 7506 | O-ring 10x3 | 1 |
| 31 | 4201 670 1700 | Coupling sleeve 1/2" | 1 |
| 32 | 4201 670 1701 | Coupling sleeve 3/4" | 1 |
| 33 | 9022 341 1070 | Spline screw IS-M5x30 | 1 |
| 34 | 4238 700 2900 | Adjusting lever | 1 |
| 35 | not sold separately | Hose 5.6x1.9x585 mm not available as a separate item | 1 |
| 36 | not sold separately | Hose 5.6x1.9x527 mm not available as a separate item | 1 |
| 37 | 4238 764 8505 | Poly V-belt pulley | 1 |
| 38 | 9291 021 0200 | Washer 10.5 | 1 |
| 39 | 9211 260 1350 | Hexagon nut M10x1 l/h thread | 1 |
| 40 | 4201 708 8402 | Hexagon head screw M10x18 | 1 |
| 41 | 9450 721 2150 | Circlip 20x1.2 | 1 |
| 42 | 4201 708 3004 | Thrust washer Ø 103 mm | 1 |
| 43 | 4201 708 3014 | Thrust washer Ø 103 mm | 1 |
| 44 | 4238 764 8504 | Poly V-belt pulley | 1 |
| 45 | 9074 478 4425 | Pan head self-tapping screw IS-P6x19 | 1 |
| 46 | 4238 700 8107 | Guard | 1 |
| 47 | 4238 700 8109 | Guard | 1 |
| 48 | not sold separately | Screw not available as a separate item | 1 |
| 49 | 9022 341 1070 | Spline screw IS-M5x30 | 1 |
| 50 | 9443 825 7130 | Hollow rivet 7.5x1x6.8 | 1 |
| 51 | 4238 701 0202 | Cast arm | 1 |
| 52 | 4224 700 8108 | Guard Ø 350 mm / 14'' | 1 |
| 53 | 4224 700 8102 | Guard Ø 350 mm / 14'' | 1 |
| 54 | 4224 700 2901 | Adjusting lever | 1 |
| 55 | 4238 670 5200 | Solenoid valve | 1 |
| 56 | 4238 700 7300 | Hose connector | 1 |
| 57 | 0000 894 3100 | Sealing ring | 1 |
| 58 | 4238 403 2200 | Cover | 1 |
| 59 | 9074 478 4425 | Pan head self-tapping screw IS-P6x19 | 1 |
| 60 | 4205 708 3000 | Thrust washer Ø 118 mm | 1 |
| 61 | 4205 708 3010 | Thrust washer Ø 118 mm | 1 |
| 62 | 4224 790 9300 | Rubber buffer | 1 |
| 63 | 9022 341 0910 | Spline screw IS-M5x6 | 1 |
| 64 | 0000 708 4200 | Shaft sleeve option | 1 |
| 65 | 0000 960 0100 | Set of instruction labels | 1 |
| 66 | 0000 960 0101 | Set of instruction labels | 1 |
| 67 | 0000 967 3903 | Instruction label | 1 |
| 68 | 0000 967 7226 | Warning pictogram | 1 |
| 69 | 4223 967 3701 | Instruction label | 1 |
| 70 | 4238 967 3700 NLA | Instruction label | 1 |
| 71 | 4238 967 3701 NLA | Instruction label | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 937 4049 | Hose 5.6x1.9 mm x 1 m not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · TS 410 / TS 420
TS 410 / TS 420: inboard guard preferred for free-hand cutting
The cast arm and magnesium guard can be mounted inboard or outboard, but the source prefers inboard for free-hand work.
- The factory installs the cast arm with its magnesium guard INBOARD. The arm/guard can be remounted OUTBOARD when required. Section 1.5 recommends INBOARD for free-hand cutting because its center of gravity is more advantageous.
- Figures 370TI008 KN and 370TI009 KN show the two configurations. The statement that conversion takes a matter of minutes does not provide the fastener sequence, belt alignment, torque or water-line routing required to perform it; this is not a full conversion procedure.
- The introductory broad application list does not remove the guard or make either position universally preferable. Wheel specification and operating instructions remain separate dependencies.
- Retained 2007 source guidance, not present-day stock availability. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 37/2007, p. 2 · TI 37/2007, p. 9 — TS 410 / TS 420: inboard guard preferred for free-hand cutting.
No additional parts-table entry added.
Service note · TS 410 / TS 420
TS 410 / TS 420: model-specific belts, ratios and machine dimensions
The two belt lengths and wheel-equipped dimensions must stay attached to their model.
- TS 410 ribbed poly belt: 0.46 in × 29.1 in (11.7 mm × 740 mm), designation 5PJ 740 LB, transmission ratio 2.00. TS 420: 0.46 in × 31.5 in (11.7 mm × 801 mm), 5PJ 801 LB, ratio 2.11. These are belt designations, not STIHL order numbers or proof of interchange.
- Weight WITHOUT cutting wheel and WITHOUT fuel: TS 410 = 20.7 lb (9.4 kg); TS 420 = 21.2 lb (9.6 kg). This is not ready-to-cut operating weight.
- Length INCLUDING cutting wheel: TS 410 = 26.57 in (675 mm); TS 420 = 28.54 in (725 mm). Height UP TO GUARD: 14.76 in (375 mm) versus 16.14 in (410 mm). Width INCLUDING HANDLEBAR is 11.81 in (300 mm) for both.
- The table does not specify belt tension, wear limits or a conversion kit between the two wheel sizes. Source inch/metric pairs are retained without using rounded values as manufacturing tolerances.
- Retained English-USA 2007 source guidance, not present-day stock availability or proof for later variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 37/2007, p. 11 — model-specific belts, ratios and machine dimensions.
No additional parts-table entry added.
Service note · TS 410 / TS 420
TS 410 / TS 420: wheel diameters and material-specific versions
TS 410 uses the listed 12-inch wheel size; TS 420 uses 14 inches.
- Both DIAMOND and COMPOSITE rows specify TS 410 = 12 in (300 mm), TS 420 = 14 in (350 mm). The table does not authorize mounting either size on either model.
- DIAMOND wheels, DEPENDING ON VERSION: asphalt, concrete, stone (hard rock), abrasive concrete, green concrete, clay bricks and clay pipes. COMPOSITE wheels, DEPENDING ON VERSION: asphalt, concrete, stone, ductile cast iron pipes and steel.
- These are application families, not a claim that every wheel cuts every listed material. No wheel order number, arbor bore, minimum wheel speed rating or wet/dry permission is supplied in this table; a complete wheel-selection procedure is not established by diameter alone.
- Retained English-USA 2007 source guidance, not present-day stock availability or proof for later variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 37/2007, p. 12 — wheel diameters and material-specific versions.
No additional parts-table entry added.
Service note · TS 410 / TS 420
TS 410 / TS 420: repair allowances: wheel drive and handles
Published minutes apply to trained personnel and properly equipped shops, not every owner repair.
- Section 7.4 applies to TRAINED AND QUALIFIED personnel and PROPERLY EQUIPPED repair shops; values are MINUTES. They are historical labor allowances, not measured performance, required service intervals or abbreviated repair procedures.
- Rows 1–5: (1) replace engine or shortblock = DASH, not zero; (2) wheel guard = 20; (3) wheel-bearing bracket assembly = 25; (4) belt pulley on wheel arbor = 15; (5) wheel-arbor shaft = 15.
- Rows 6–10: (6) arbor-shaft bearing = 25; (7) belt pulley on clutch end = 25; (8) drive belt = 15; (9) front handlebar = 15; (10) cast arm from engine to wheel = 25. All are replacement activities for TS 410/420.
- The blank/dash engine allowance does not mean a complete engine replacement takes no labor. Allowances for combined jobs are not specified and must not be automatically summed.
- Retained English-USA 2007 source guidance, not present-day stock availability or proof for later variants. No numeric serial cutoff is supplied. No physical interchange test was performed.
Source: TI 37/2007, p. 16 — repair allowances: wheel drive and handles.
No additional parts-table entry added.
Wrong number or missing part for the TS 410, TS 420? Report a correction →