Stihl 4311 · Section C · 3 of 13 · 22 parts
Ignition system, Clutch
Fits BT 106.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (22)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4129 400 1200 | Flywheel Fitment / change note → | 1 |
| 2 | 9291 021 0180 | Washer 8.4 | 1 |
| 3 | 9210 260 1100 | Hexagon nut M8 | 1 |
| 4 | 4222 400 1300 | Ignition coil Fitment / change note → | 1 |
| 5 | not sold separately | Ignition lead 175 mm | 1 |
| 5 | 0000 405 0600 NLA | Ignition lead 1 m option | 1 |
| 5 | 0000 930 2251 | Ignition lead 10 m option | 1 |
| 6 | 0000 989 1010 | Grommet | 1 |
| 7 | 4126 440 1101 | Short circuit wire | 1 |
| 8 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 2 |
| 9 | 4126 432 9200 | Grommet | 1 |
| 10 | 4112 432 9202 | Grommet | 1 |
| 11 | 4129 084 1000 | Fan housing | 1 |
| 12 | 4126 400 1001 | Trigger unit Fitment / change note → | 1 |
| 13 | 9022 341 0980 | Spline screw IS-M5x16 | 4 |
| 14 | 9022 313 0660 | Spline screw IS-M4x12 | 1 |
| 15 | 4113 160 2000 | Clutch | 1 |
| 16 | 0000 997 6100 | Tension spring | 1 |
| 17 | 4129 997 1200 | Tension spring | 1 |
| 18 | 4117 162 8900 | Washer | 2 |
| 19 | 4129 162 8900 | Washer | 2 |
| 20 | 4129 162 4200 | Collar screw | 2 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · BT 106
BT 106: series 4311 replacement ignition assignment
4222 400 1300 + 4126 400 1001 with flywheel 4129 400 1200; 175 mm ignition lead.
- Printed series 4311. Use 4222 400 1300 and 4126 400 1001 with flywheel 4129 400 1200.
- Printed ignition-lead length: 175 mm (6 7/8 in). Preserve both printed units.
- TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
- Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
- Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
- Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
- Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.
- Footnote 1 identifies an ignition coil; footnote 2 identifies a separate trigger unit. These are components of the listed system, not two interchangeable replacement modules.
Source: TI 1/1999, p. 1 · TI 1/1999, p. 3 — 1.1 general restrictions and 1.2.2 power-tool assignments.
Part numbers (3)
- 4222 400 1300 — Ignition coilAssigned component · BT 106, printed series 4311, listed combination only
- 4126 400 1001 — Trigger unitAssigned component · BT 106, printed series 4311, listed combination only
- 4129 400 1200 — Assigned flywheelRequired pairing · BT 106, printed series 4311
Wrong number or missing part for the BT 106? Report a correction →