← BE 55, BGE 60

Stihl 4804 · Section C · 3 of 5 · 8 parts

Electric motor BGE 60

Fits BGE 60.

Parts diagrams →

Historical fitment & changes (8) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
123456788
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (8)

PosPart numberDescriptionQty
1 4807 600 0201 Electric motor 100/120 V 1
2 4804 704 3400 Fanwheel 1
3 4804 708 3000 Thrust washer 1
4 4807 440 3006 Wiring harness Fitment / change note → 1
5 4807 440 3011 Wiring harness 1
6 4807 440 3001 Wiring harness Fitment / change note → 1
7 4807 440 3005 Wiring harness 1
8 4807 430 0500 Switch 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · BGE 60

BGE 60: housing, cord grip and household blower configuration

Single-phase electric blower with an integral handle and cord restraint; the vacuum attachment is optional equipment.

  • Page1 introduces BGE60 series4807 for household leaf, paper and debris blowing on flowerbeds, lawns and paths. Photograph shows the blower tube, integral handle and short connecting lead. No internal parts or dimensions are inferred from the photograph.
  • Page2 section1 specifies a single-phase AC drive motor in a high-impact plastic housing. The housing cord grip relieves strain on the plug; the handle is integral with the housing and carries an ON/OFF switch.
  • The vacuum attachment is a SPECIAL ACCESSORY, not included by this introduction. Residential-noise/directive marketing is historical context, not evidence of current legal compliance or permission to operate. No bayonet attachment or interlock design is supplied here.
  • Historical BGE 60, TI38/1998 series 4807, 120 V / 60 Hz specification only. Catalog grouping under 4804 does not equate the series or extend BE 55 procedures to BGE 60. No serial changeover, later-model compatibility or current availability inferred. No hardware operation was performed.

Source: TI 38/1998, p. 1 · TI 38/1998, p. 2 — Introduction and photograph; complete section1.

No additional parts-table entry added.

Service note · BGE 60

BGE 60: 120 V motor and double insulation

120 V, 60 Hz, 1150 W, 9.6 A and 9,800 RPM are the stated BGE60 specification.

  • Complete section2 Motor block: voltage120 V; frequency60 Hz; rating1150 W; rated current9.6 A; rated speed9,800 RPM; DOUBLE INSULATION, shown by the square-in-square symbol. Retain printed rating/current separately rather than replacing either by a computed value.
  • These are source specifications, not a tested speed or a connection/test procedure. The later exact-model motor sheet lists a100/120 V motor; that broader label does not change this TI120 V specification or authorize230/240 V operation. No motor order number appears in this TI.
  • Historical BGE 60, TI38/1998 series 4807, 120 V / 60 Hz specification only. Catalog grouping under 4804 does not equate the series or extend BE 55 procedures to BGE 60. No serial changeover, later-model compatibility or current availability inferred. No hardware operation was performed.

Source: TI 38/1998, p. 2 — Section2 complete motor specifications and insulation symbol.

No additional parts-table entry added.

Service note · BGE 60

BGE 60: airflow, noise, weight and dimensions

Keep blower/vacuum modes, the 50-foot noise distance and tube-excluded dimensions distinct.

  • Blower-mode sound pressure is63 dB(A) at50 ft to ANSI B175.2-1990. It is not sound power or an operator-ear measurement. The historical standard designation is retained, not replaced by a newer method.
  • Maximum air flow362 cfm; in VACUUM MODE at9,800 RPM315 cfm. Air velocity is printed203 ft/s–138 m.p.h. Do not merge the two flow values or treat the rounded speed pair as two operating settings.
  • Weight FULLY ASSEMBLED2.9 kg (6.4 lbs). Dimensions WITHOUT BLOWER TUBE: length375 mm (14.76 in), width210 mm (8.26 in), height330 mm (13.0 in). No unsupported vacuum-assembly weight or full tube-equipped length inferred.
  • Historical BGE 60, TI38/1998 series 4807, 120 V / 60 Hz specification only. Catalog grouping under 4804 does not equate the series or extend BE 55 procedures to BGE 60. No serial changeover, later-model compatibility or current availability inferred. No hardware operation was performed.

Source: TI 38/1998, p. 2 — Section2 complete noise table, airflow, weight and dimensions.

No additional parts-table entry added.

Service note · BGE 60

BGE 60: spline drivers and connector crimping tool

The three listed tools have specific screw/connector applications; no electrical test settings are given.

  • Section5 lists screwdriver bit for torque wrench I-5 x120 x6.3,0812 542 2104, for IS spline screws; T-handle screwdriver QI-5 x150,5910 890 2400, also for IS spline screws; crimping tool5910 890 8210 for cable connectors,lugs,etc.
  • The tool table supplies no terminal pinout, wire size, crimp die, insulation-test instrument or Hi-Pot voltage/duration/leakage limit. A listed hand driver is not itself a torque-limiting device. Tool names/numbers are procedural references, not motor replacement parts.
  • Historical BGE 60, TI38/1998 series 4807, 120 V / 60 Hz specification only. Catalog grouping under 4804 does not equate the series or extend BE 55 procedures to BGE 60. No serial changeover, later-model compatibility or current availability inferred. No hardware operation was performed.

Source: TI 38/1998, p. 3 — Section5 complete three-row table.

No additional parts-table entry added.

Service note · BGE 60

BGE 60: repair times and motor-failure warranty exception

The starred 0.2-hour motor entry covers historical whole-machine warranty handling, not motor replacement labor.

  • Section7 assumes trained personnel in a properly equipped service workshop. Units are TENTHS OF AN HOUR;0.1h=6minutes. All repair times INCLUDE electrical leakage test (Hi-Pot test) time; this is not a test procedure or evidence a machine passed.
  • Complete table: code1 Power Cord0.4h;2 On/Off Switch0.4h;3 Replace Motor Housing0.5h;4 Drive Tube,Drive Shaft DASH;5 Blower Tube0.3h;6 Replace Gear Box/Arbor Assy.DASH;7 Replace Arbor Gears DASH;8 Replace Motor STARRED0.2h;20 Misc.Repairs0.5h. Dashes are not zero-time repairs, missing part recommendations or blower drive-shaft/gearbox fitment.
  • The asterisk says REPLACE COMPLETE MACHINE for WARRANTY failures of the BGE60 motor. The0.2h allowance is for completing the warranty claim and returning the machine to the STIHL Distributor. Do not present it as12minutes of motor-removal/installation labor, an owner obligation, current warranty entitlement or an instruction to contact a distributor.
  • No additivity or total repair duration is specified. This bulletin supplies no Hi-Pot settings, discharge procedure or detailed electrical repair method; those remain unestablished and no energized test was performed.
  • Historical BGE 60, TI38/1998 series 4807, 120 V / 60 Hz specification only. Catalog grouping under 4804 does not equate the series or extend BE 55 procedures to BGE 60. No serial changeover, later-model compatibility or current availability inferred. No hardware operation was performed.

Source: TI 38/1998, p. 4 — Section7 complete nine-row repair table, all preconditions, asterisk and Hi-Pot note.

No additional parts-table entry added.

Conditional replacement · BGE 60

BGE 60: 2002 capacitor harness is not an older-machine replacement

4807 440 3006 is for new machine versions only; retain 4807 440 3001 for older USA/CDN machines.

  • The complete summary row lists cable harness (USA, CDN): previous 4807 440 3001; new 4807 440 3006. Remarks 1 and 2 explicitly retain the previous harness for older models and restrict the new version to new machine versions. The leading replacement wording is NOT unconditional supersession.
  • Page 1 states that the new harness incorporates an integrated capacitor and CANNOT be used for older models. Drawing 291TI000 KN places the previous harness at TOP and new capacitor harness at BOTTOM. The capacitor is part of the depicted harness change; no standalone capacitor order number or capacitance/rating is given.
  • The retained SCS 01-2012 exact BGE 60 motor sheet lists BOTH 3006 at position 4 and 3001 at position 6; their coexistence does not imply interchange. The same sheet also lists 4807 440 3011 at 5 and4807 440 3005 at 7: TI 22 supplies no mapping or replacement authorization for those two numbers.
  • All other parts as before is the summary statement, not permission to ignore the adapted housings discussed on page 1. No serial/date threshold identifies a particular machine as new. Last-TI reference 38.1998 establishes chronology, not backdating of the capacitor to the 1998 introduction.
  • Historical BGE 60, series 4807, TI 22/2002 English/USA only; the numbered harness row is USA/CDN. No serial changeover, BE 55 applicability, 230 V conversion, current stock availability or energized repair/test procedure is established. No hardware operation was performed.

Source: TI 22/2002, p. 1 · TI 22/2002, p. 2 — Complete cable-harness text,291TI000 KN comparison,summary row and both remarks; last-TI reference.

Part numbers (2)
  • 4807 440 3001 — Cable harness (USA, CDN)Previous version retained · Older BGE 60 machine versions; retained availability is historical
  • 4807 440 3006 — Cable harness (USA, CDN)Restricted new version · New BGE 60 machine versions only; NOT older machines

Service note · BGE 60

BGE 60: 2002 housing compatibility is one-way

New housing halves may serve earlier BGE 60 machines; that does not permit the new harness on an older machine.

  • Page 1 service note says BOTH housing halves were adapted to accept the modified harness. New housing halves CAN also be used for previous machine models. The separate prohibition on fitting the new harness to older machines remains in force; replacing housings is not an authorized conversion recipe.
  • Drawing 291TI002 KN compares LEFT-HAND housing halves; 291TI003 KN compares RIGHT-HAND halves. In EACH pair, LEFT is previous and RIGHT is new. The added/changed internal retaining geometry accommodates the capacitor/wire arrangement; no cut, drill, glue or hand-modification method is specified.
  • The reverse direction (old housings on a new machine) is not authorized. No new/previous housing order numbers, dimensional tolerances or required modification of an old shell are printed. Retained 2012 handle-molding numbers do not establish which 2002 revision is on an individual machine.
  • Historical BGE 60, series 4807, TI 22/2002 English/USA only; the numbered harness row is USA/CDN. No serial changeover, BE 55 applicability, 230 V conversion, current stock availability or energized repair/test procedure is established. No hardware operation was performed.

Source: TI 22/2002, p. 1 — Entire service note and both labeled housing-comparison diagrams.

No additional parts-table entry added.

Service note · BGE 60

BGE 60: 2002 capacitor and cable routing diagram

Use the new-version routing figure; this is not a pinout or electrical safety-test specification.

  • Page 2 Routing requires BOTH cable routing and capacitor position to match 291TI004 KN. The square-bodied capacitor is drawn in the upper-left internal pocket, below the switch region; the leads follow the depicted molded routes around the motor and to its terminals. These are orientation cues to the original figure, not an inferred wire-color map.
  • The entire drawing, including the housing edge, motor, terminals and supports, was reviewed. Do not substitute the earlier capacitor-free harness picture or BE 55 routing. No conductor colors, terminal numbering, capacitor discharge method, electrical test voltage/duration/leakage limit or complete circuit schematic is provided.
  • This is a later new-version BGE 60 harness instruction only, not a substitute for the owner-safety precautions and Hi-Pot procedure absent from the 1998 introduction. The footer identifies copyright 2002 and document 7745; no production serial or original 1998 electrical configuration can be inferred.
  • Historical BGE 60, series 4807, TI 22/2002 English/USA only; the numbered harness row is USA/CDN. No serial changeover, BE 55 applicability, 230 V conversion, current stock availability or energized repair/test procedure is established. No hardware operation was performed.

Source: TI 22/2002, p. 2 — Complete routing instruction and291TI004 KN figure; footer.

No additional parts-table entry added.

Wrong number or missing part for the BGE 60? Report a correction →