Stihl 4804 · Section B · 2 of 5 · 23 parts
Housing BE 55
Fits BE 55.
Historical fitment & changes (9) — includes parts and conditions not shown on this drawing.
Parts (23)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 4804 791 1105 | Handle molding, left 120 V | 1 |
| 1 | 4804 791 1107 | Handle molding, left 230/240 V Fitment / change note → | 1 |
| 2 | 4804 791 1100 | Handle molding, right 120 V | 1 |
| 2 | 4804 791 1101 | Handle molding, right 230/240 V | 1 |
| 3 | 4804 967 1800 | Rating plate 120 V | 1 |
| 3 | 4804 967 1801 | Rating plate 230/240 V | 1 |
| 4 | 4803 791 6600 | Flap | 1 |
| 5 | 4803 791 8200 | Torsion spring | 1 |
| 6 | 9074 478 4425 | Pan head self-tapping screw IS-P6x19 | 8 |
| 7 | 4804 706 8000 | Screen | 1 |
| 8 | 0000 998 0807 | Torsion spring | 1 |
| 9 | 4227 700 1800 | Blower tube Fitment / change note → | 1 |
| 10 | 4227 708 6300 NLA | Nozzle | 1 |
| 11 | 4227 700 7102 | Hose clip Fitment / change note → | 1 |
| 12 | 4227 701 5000 | Screw Fitment / change note → | 1 |
| 13 | 4227 708 0105 | Adapter option | 1 |
| 14 | 4227 700 7105 | Hose clip option | 3 |
| 15 | 4227 708 3405 | Tube option | 3 |
| 16 | 4227 708 6905 | Manifold option | 2 |
| 17 | 0000 967 3668 | Instruction label | 1 |
| 30 | 4804 791 1106 | Handle molding, left 230 V Fitment / change note → → replaced by 4804 791 1107 TI 34/1996 | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 4227 007 1005 | Gutter cleaning kit option | 1 |
| — | 0000 884 0307 | Safety glasses not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · BE 55
BE 55: housing, cord restraint and bayonet blower tube
Integral handle and ON/OFF switch; axially adjustable blower tube has a quick-action bayonet coupling.
- The single-phase motor sits in a high-impact plastic housing with integral handle, supply-cord strain relief and handle-positioned ON/OFF switch. Smooth surfaces are described as easier to clean. The tube adjusts axially and uses a quick-action bayonet coupling; no coupling dimensions or cross-model tube interchange are established.
- Fully assembled weight is 2.9 kg (6.4 lb). Dimensions WITHOUT blower tube: length 375 mm (14.76 in), width 210 mm (8.26 in), height 350 mm (13.78 in). Do not interpret these dimensions as including the tube or vacuum attachment.
- The page 1 product image and domestic leaf/debris blowing and vehicle-drying description identify the introduced machine; marketing claims about power, price and ease of use are not fitment evidence. The optional vacuum accessory is treated separately.
- Historical English TI 04/1994, series 4804 BE 55 only. Shared BE 55/BGE 60 catalog grouping does not extend these assertions to BGE 60, other voltages or later variants. No physical interchange test was performed.
Source: TI 4/1994, p. 1 · TI 4/1994, p. 2 — housing, cord restraint and bayonet blower tube.
No additional parts-table entry added.
Service note · BE 55
BE 55: airflow and noise figures retain their measurement context
595 m³/h maximum airflow; vacuum attachment 535 m³/h at 9,500 rpm; noise values are not interchangeable.
- Maximum airflow is 595 m³/h (350 Cfm); airflow with vacuum attachment is 535 m³/h (315 Cfm) at 9,500 rpm. Air velocity is 59 m/s (132 mph). These are printed performance figures, not bench measurements; the airflow-speed label does not replace the separately specified 9,400 rpm rated motor speed.
- Equivalent sound pressure to ISO 6081 is 85 dB(A) in BOTH blowing and vacuum modes. Equivalent sound power to ISO 3744 is 97 dB(A) blowing and 100 dB(A) vacuum. Preserve pressure versus power and operating mode.
- Page 1 separately states a bystander sound level below 65 dB(A) at 50 ft. That distance-specific claim is not the ISO 6081 pressure row, sound power, or proof of safe unprotected exposure. No new noise test or conversion was performed.
- Historical English TI 04/1994, series 4804 BE 55 only. Shared BE 55/BGE 60 catalog grouping does not extend these assertions to BGE 60, other voltages or later variants. No physical interchange test was performed.
Source: TI 4/1994, p. 1 · TI 4/1994, p. 2 — airflow and noise figures retain their measurement context.
No additional parts-table entry added.
Service note · BE 55
BE 55: motor-housing screw torque
IS-P 6×19 spline screw: 3.0 Nm (2.2 lbf ft), confined to the motor housing.
- Section 5 specifies spline screw IS-P 6×19 for the motor housing at 3.0 Nm (2.2 lbf ft). No part number or screw count is supplied in this table.
- This is a component- and fastener-specific setting, not a general torque for the motor, vacuum attachment or every screw in series 4804. Do not infer a replacement screw number from dimensions alone.
- Historical English TI 04/1994, series 4804 BE 55 only. Shared BE 55/BGE 60 catalog grouping does not extend these assertions to BGE 60, other voltages or later variants. No physical interchange test was performed.
Source: TI 4/1994, p. 3 — motor-housing screw torque.
No additional parts-table entry added.
Service note · BE 55
BE 55: listed spline-screw and connector service tools
0812 542 2104 and 5910 890 2400 for IS spline screws; 5910 890 8210 for connectors/lugs.
- The torque-wrench screwdriver bit I-5×120×6.3 is 0812 542 2104; T-handle screwdriver QI-5×150 is 5910 890 2400. Both are listed for IS spline screws. The original scan confirms the tool designations; these are tools, not installed blower components.
- Crimping tool 5910 890 8210 is listed for electric connectors, lugs, etc. No crimp-die size, terminal specification, replacement connector number or electrical acceptance criterion is provided. Tool listing is not permission to operate a connected machine.
- Historical English TI 04/1994, series 4804 BE 55 only. Shared BE 55/BGE 60 catalog grouping does not extend these assertions to BGE 60, other voltages or later variants. No physical interchange test was performed.
Source: TI 4/1994, p. 4 — listed spline-screw and connector service tools.
Part numbers (3)
- 0812 542 2104 — Torque-wrench screwdriver bit I-5×120×6.3service-tool · BE 55 — listed spline-screw and connector service tools
- 5910 890 2400 — T-handle screwdriver QI-5×150service-tool · BE 55 — listed spline-screw and connector service tools
- 5910 890 8210 — Crimping tool for electrical connectors/lugsservice-tool · BE 55 — listed spline-screw and connector service tools
Service note · BE 55
BE 55: repair-manual reference is conditional
FE 35/40/55 and EC 70 instructions may be used only where applicable to BE 55.
- Section 7 permits the service manual for FE 35, FE 40, FE 55 and EC 70 to be used as a reference WHERE APPLICABLE for BE 55 repairs. This is not a claim that the machines, components, wiring, voltages or all procedures are identical.
- If the unit is started during repairs or maintenance, the bulletin requires all local safety regulations and the owner manual precautions to be observed. The bulletin does not reproduce those precautions or a full repair procedure. Referenced manuals have not been reviewed by proxy or admitted as whole manuals in this TI batch; their absence here does not invalidate this bounded reference statement.
- Historical English TI 04/1994, series 4804 BE 55 only. Shared BE 55/BGE 60 catalog grouping does not extend these assertions to BGE 60, other voltages or later variants. No physical interchange test was performed.
Source: TI 4/1994, p. 4 — repair-manual reference is conditional.
No additional parts-table entry added.
Service note · BE 55
BE 55: historical workshop repair-time allowances
10 minutes each for cord/plug, housing, switch and motor; 5 minutes for electrical safety check.
- The BE 55 series 4804 table gives minutes: cord with plug 10; motor housing 10; switch 10; motor 10; electrical safety check 5. These times assume trained personnel in a properly equipped service workshop.
- These are task allowances, not machine operating durations, guaranteed owner repair times, a cumulative job quote or electrical pass/fail criteria. The safety check remains a distinct row; no test voltage, leakage limit or test sequence is provided. Publication footer: Waiblingen, February 4,1994.
- Historical English TI 04/1994, series 4804 BE 55 only. Shared BE 55/BGE 60 catalog grouping does not extend these assertions to BGE 60, other voltages or later variants. No physical interchange test was performed.
Source: TI 4/1994, p. 4 — historical workshop repair-time allowances.
No additional parts-table entry added.
Historical fitment · BE 55
BE 55: three-terminal switch and matching 0/I housing
0505 becomes 0502; revised left housing removes II. Old parts remain available for other models.
Later reviewed guidance: BE 55: 1997 switch revision and differing old-part supply wording
- Section 1 replaces switch 4804 430 0505 with 4804 430 0502. Only positions 0 and I may be selected, and the new switch has THREE connector tags instead of FOUR. Figure 358TI002 identifies drawing 1 as original and 2 as new; these drawing labels are not terminal numbers.
- Section 2 replaces left housing 4804 791 1106 with 4804 791 1107 to match the changed switch. The new marking is 0 and I only; II is deleted. Figure 358TI001 shows the marking area. Do not retain a two-speed claim for the revised configuration or assume the original and modified switches have identical connections.
- The TI attributes this change to licensing regulations without identifying a jurisdiction or standard; it is a historical source statement, not a present compliance determination. Introduction is IN PROGRESS with no serial cutoff or precise date. Remark 1 retains the original switch and housing for OTHER MODELS, not as an unconditional alternative for this modified BE 55.
- The later exact BE 55 IPL describes 0505/1106 as 230 V and 0502/1107 as 230/240 V; separate 120 V parts are also listed. TI34 itself does not specify a voltage conversion. Do not extend the change to the 120 V components, to BGE 60 on the combined catalog product, or to other models that retain the originals.
- Historical TI 34/1996 evidence; not current stock or verified physical interchange. No hardware operation was performed.
Source: TI 34/1996, p. 1 · TI 34/1996, p. 2 — BE 55: three-terminal switch and matching 0/I housing.
Part numbers (4)
- 4804 430 0505 — Original four-tag switchOriginal; retained for other models · BE 55 original configuration; not unrestricted revised-machine spare
- 4804 430 0502 — Modified three-tag 0/I switchNew switch · BE 55 configuration described by TI34
- 4804 791 1106 — Original left housingOriginal; retained for other models · BE 55 original switch markings
- 4804 791 1107 — Modified left housingNew 0/I markings; II deleted · BE 55 modified-switch configuration
Historical fitment · BE 55
BE 55: 1997 switch revision and differing old-part supply wording
German TI38 says older machines; English TI34 says other models. Neither establishes unrestricted interchange.
- Section 1 replaces switch 4804 430 0505 with 4804 430 0502: only positions 0 and I can be selected; THREE flat connector tags in a row replace FOUR. Figure 358TI002 KN labels 1 as former and 2 as new; these are version labels, NOT terminal numbers.
- Section 2 replaces left housing 4804 791 1106 with 4804 791 1107 to match the switch. Only 0 and I remain printed; position II is deleted. Figure 358TI001 KN locates the marking. Do not treat the old four-tag and new three-tag switches as identical connections or infer an unprinted mixed-component retrofit.
- Summary remark 1 explicitly says the former switch and housing remain available for OLDER MACHINES (German: für ältere Geräte weiterhin lieferbar). Earlier English TI34/1996 page 2 instead says OTHER MODELS. This is a retained source-wording conflict, not silently normalized to one availability scope. Neither statement proves unrestricted interchange with the modified configuration. No evidence establishes whether translation, market or revision explains the difference.
- Introduction is GRADUAL (einfließend), without a serial cutoff or precise introduction date. Changed approval regulations are given as the reason, but no jurisdiction or named standard is supplied. This is not a present compliance determination or evidence that the earlier English issue was withdrawn.
- The exact BE 55 catalog motor/housing sheets list 0505/1106 as 230 V and 0502/1107 as 230/240 V, alongside distinct 120 V components. The TI itself does not state a voltage conversion. Keep BE 55 separate from BGE 60 despite their shared product heading; do not extend this change to 120 V parts.
- The footer cites prior BE 55 TI04.94, not TI34.96. The matching diagrams and numbers support comparison of the two retained issues, not an invented publication chronology or a second hardware change.
- Historical German TI38/1997, not current stock or verified physical interchange. No hardware operation was performed.
Source: TI 38/1997, p. 1 · TI 38/1997, p. 2 — Sections1–2, both version/marking drawings, page2 summary rows1–2, introduction and supply remark1.
Referenced bulletin evidence: TI 34/1996, p. 2 — Earlier English summary, wiring and supply remarks; wording difference retained.
Part numbers (4)
- 4804 430 0505 — Original four-tag switchFormer version retained for older machines in TI38 · BE 55 configuration in German TI38/1997; not BGE 60 or a voltage conversion
- 4804 430 0502 — Modified three-tag switchNew 0/I-only version · BE 55 configuration in German TI38/1997; not BGE 60 or a voltage conversion
- 4804 791 1106 — Original left housingFormer version retained for older machines in TI38 · BE 55 configuration in German TI38/1997; not BGE 60 or a voltage conversion
- 4804 791 1107 — Modified left housingNew 0/I markings; II deleted · BE 55 configuration in German TI38/1997; not BGE 60 or a voltage conversion
Conditional replacement · BE 55
BE 55: marked blower tube from X 38 705 142
New tube includes clamp and screw; earlier tubes remain interchangeable according to the TI.
X 38 705 142 — Blower-tube production introduction only; not the vacuum-attachment introduction, a model-identification range or a lower bound on older-machine replacement.
- Section 2 replaces blower tube 4227 708 3400 with 4227 700 1800 FROM machine number X 38 705 142. Both prose and the second summary print this cutoff. Preserve the X prefix; it is production introduction of this blower-tube revision, not a BE 55 identity range or the vacuum-attachment introduction.
- The housing and blower tube now carry MARKINGS to assure correct assembly and alignment. ORIGINAL AND NEW BLOWER TUBES ARE FULLY INTERCHANGEABLE according to the source. Summary remark 2 also permits the new version on OLDER MACHINES, so the production cutoff is not a lower limit on replacement eligibility.
- Blower summary item 1 new tube includes item 2 clamp 4227 700 7102; item 2 includes item 3 screw 4227 701 5000. Original clamp/screw columns are dashes, not additional part numbers. No tightening torque, clamp size or unprinted assembly procedure is invented.
- Blower summary remark 1 keeps original tube 4227 708 3400 available from the factory ONLY AS LONG AS EXISTING STOCKS LAST. The duplicated wording “wird will” in the original remark does not alter the stock-exhaustion meaning. This is not current availability.
- The exact BE 55 housing IPL lists tube 4227 700 1800, hose clip 4227 700 7102 and screw 4227 701 5000, agreeing with these new part numbers. The BGE 60 housing sheet instead lists blower tube 4807 700 1800; shared grouping or shared fasteners do not extend BE 55 interchange to BGE 60. Footer prior TI38.97, copyright1998 and documentation6274 are bibliographic context, not delegated assembly instructions or extra cutoffs.
- Historical TI09/1998, BE 55 electric blower, series 4804 ONLY. The shared BE 55/BGE 60 catalog grouping does not extend these statements to BGE 60. Factory availability is historical, not current stock. Source-stated interchange is not a reproduced physical fit test. No hardware operation was performed.
Source: TI 9/1998, p. 1 · TI 9/1998, p. 2 — Section 2 complete prose, three summary rows/inclusions, exact cutoff, both remarks and footer.
Part numbers (4)
- 4227 708 3400 — Original blower tubeFactory supply only while existing stocks last · BE 55; exact configuration and restrictions in this note
- 4227 700 1800 — Marked blower tube; includes clamp item 2New; source-stated full interchange · BE 55; exact configuration and restrictions in this note
- 4227 700 7102 — Clamp; includes screw item 3New tube inclusion · BE 55; exact configuration and restrictions in this note
- 4227 701 5000 — ScrewIncluded in clamp · BE 55; exact configuration and restrictions in this note
Wrong number or missing part for the BE 55? Report a correction →