← 024 · 026 · MS 260 · MS 240

Stihl 1121 · Section A · 1 of 17 · 31 parts

Crankcase

Fits 026.

Parts diagrams →

Historical fitment & changes (3) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1110111213131415161718192220212324252627282933031456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (31)

PosPart numberDescriptionQty
1 1121 020 2117 Crankcase Fitment / change note → 1
2 1121 020 2112 Crankcase Fitment / change note → → replaced by 1121 020 2117 TI 43/2001 1
3 0000 988 5211 Connector 1
4 9416 868 6531 Hollow rivet 6.5x0.5x6.8 2
5 9371 470 2610 Cylindrical pin 5x18 2
6 0000 974 1200 Notched pin 2.6x8 1
7 1128 640 9100 Valve 1
8 9523 003 4260 Grooved ball bearing 15x35x13 1
9 9503 003 0320 Grooved ball bearing 16002 1
10 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 5
11 1120 162 5200 Pin 1
12 1121 162 5205 Pin 1
13 1121 162 5200 Pin 2
14 0000 953 6605 Collar screw M8 2
15 1122 647 9400 Hose 1
16 1117 640 3800 Pickup body 1
17 9640 003 1600 Oil seal 15x29.6x4 1
18 9640 003 1190 Oil seal 12x20x5 1
19 1121 029 0500 Gasket 1
20 1121 030 0405 Crankshaft 1
21 1120 036 8500 Woodruff key 2x3.7 1
23 9645 948 2470 O-ring 23x3 Fitment / change note → 1
24 0000 350 0510 Filler cap Fitment / change note → 1
25 0000 359 1210 Sealing ring 1
26 0000 350 0900 Rope 1
27 0000 353 0600 Hook 1
28 1110 664 0501 Bumper spike 1
29 9022 341 0960 Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 2
30 9214 320 0700 Lock nut M5 1
31 1124 084 8301 Reflector foil 1
Not numbered on the diagram — assemblies, kits and options
— 1121 007 1050 Set of gaskets 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · 026 / MS 260

026 / MS 260: clip caps and replacement fuel-tank housing

Same cap design does not mean the same fuel/oil cap or sealing ring.

  • Both tanks use the tool-free hinged-clip design, but fuel cap 0000 350 0525 and oil cap 0000 350 0526 have different numbers and seals. Modified filler openings are required; the TI does not authorize a cap-only conversion of an old filler neck.
  • To open the depicted cap, raise the clip and turn about a quarter-turn counterclockwise. To close, align the marks with the clip raised, turn about a quarter-turn clockwise to the stop, then fold the clip down. Proper closure requires the clip lug to engage its recess. These instructions describe the historical cap shown in the TI.
  • Tank housing 1121 350 0829 replaces 1121 350 0828 with a modified neck and new vent. The old housing includes the old vent (summary item16); the new housing includes items14–17: fuel cap, 25 x 3.5 sealing ring, new vent and its 10 x 2 ring. The clip cap was to be supplied with the new housing for about three years, enabling repairs to 026 saws; that historical packaging period is not a current kit-content guarantee. Old housing supply is limited to existing factory stocks.
  • Fuel cap 0000 350 0520 changes to 0000 350 0525 with ring 9645 948 7734 (25 x 3.5). Oil cap 0000 350 0510 changes to 0000 350 0526 with ring 9645 948 2470 (23 x 3). Both old caps remain available for older machines.
  • Shared IPL sheets do not extend these changes to unnamed variants. Introduction is in progress; the TI gives no numerical serial cutoff. Availability is the historical 2001 factory statement, not current stock. Later catalog numbers do not replace the historical evidence or prove unrestricted interchangeability.

Source: TI 43/2001, p. 2 · TI 43/2001, p. 3 · TI 43/2001, p. 7 · TI 43/2001, p. 8 — Sections3–4, all cap-operation diagrams and summary rows12–15,24–25/remarks1–2.

Part numbers (8)
  • 1121 350 0828 — Fuel-tank housingPrevious; stocks only · Only the named model/configuration; see conditions
  • 1121 350 0829 — Fuel-tank housing with items14–17New · Only the named model/configuration; see conditions
  • 0000 350 0520 — Fuel capPrevious; retained · Only the named model/configuration; see conditions
  • 0000 350 0525 — Fuel clip capNew; fuel only · Only the named model/configuration; see conditions
  • 9645 948 7734 — Sealing ring 25 x 3.5New fuel-cap seal · Only the named model/configuration; see conditions
  • 0000 350 0510 — Oil capPrevious; retained · Only the named model/configuration; see conditions
  • 0000 350 0526 — Oil clip capNew; oil only · Only the named model/configuration; see conditions
  • 9645 948 2470 — Sealing ring 23 x 3New oil-cap seal · Only the named model/configuration; see conditions

Conditional replacement · 026 / MS 260

026 / MS 260: crankcases for clip cap and revised wiring

Ordinary and quick-tensioner crankcases have different replacement numbers.

  • Ordinary crankcase 1121 020 2112 changes to 1121 020 2117; the quick-chain-tensioner version changes from 1121 020 2114 to 1121 020 2115. Keep these configurations separate. Both previous versions remain available for older machines.
  • The revised cases have modified oil filler openings for the clip cap and changes for the ignition-lead routing. This is not a claim that an old cap, old wiring path or either crankcase variant can be freely mixed with the new configuration.
  • Shared IPL sheets do not extend these changes to unnamed variants. Introduction is in progress; the TI gives no numerical serial cutoff. Availability is the historical 2001 factory statement, not current stock. Later catalog numbers do not replace the historical evidence or prove unrestricted interchangeability.

Source: TI 43/2001, p. 4 · TI 43/2001, p. 5 · TI 43/2001, p. 7 · TI 43/2001, p. 8 — Section5, section7 routing context and summary rows22–23/remark1.

Part numbers (4)
  • 1121 020 2112 — Ordinary crankcasePrevious; retained · Only the named model/configuration; see conditions
  • 1121 020 2117 — Ordinary crankcaseNew · Only the named model/configuration; see conditions
  • 1121 020 2114 — Quick-chain-tensioner crankcasePrevious; retained · Only the named model/configuration; see conditions
  • 1121 020 2115 — Quick-chain-tensioner crankcaseNew · Only the named model/configuration; see conditions

Conditional replacement · 026 / 026 C

026 C: quick tensioner retrofit requires a different crankcase

A sprocket-cover-only conversion is not supported: the crankcase must be replaced at the same time.

  • The 026 C quick-tensioner version uses a modified crankcase. Machines without this tensioner can be backfitted only if the crankcase is replaced at the same time. The TI therefore says there is no quick chain tensioner conversion kit; this is a 1998 supply statement, not proof about all later products.
  • Page3 item1 crankcase 1121 020 2114 includes item2, one M8 collar screw 0000 664 2405. Both carry remark1: replacement parts for machines with quick chain tensioner. All other crankcase parts are as before; that sentence does not waive the replacement-crankcase requirement or identify a complete conversion bill of materials.
  • The retained 2012 026 quick-tensioner sheet also lists crankcase 1121 020 2115. This TI does not explain that later number; no automatic supersession or reverse interchange is inferred.
  • Historical TI 39/1998, series 1121 only. The 026 catalog binding locates the 026 C quick-chain-tensioner version described here; it does not extend these special parts to every 026, to an 024 quick-tensioner conversion or to MS 260 successors. Introduction was in progress; no serial threshold, current availability or measured physical interchange is established. No hardware operation was performed.

Source: TI 39/1998, p. 2 · TI 39/1998, p. 3 — Section2 retrofit restriction; page3 items1–2,remark1 and all-other-parts statement.

Part numbers (2)
  • 1121 020 2114 — Crankcase; includes item2Required crankcase · 026 C with quick chain tensioner; TI 39/1998 only
  • 0000 664 2405 — Collar screw M8; one included with crankcaseIncluded component · 026 C with quick chain tensioner; TI 39/1998 only

Wrong number or missing part for the 026? Report a correction →