← 024 · 026 · MS 260 · MS 240

Stihl 1121 · Section F · 6 of 17 · 27 parts

Quick chain tensioner

Fits 026.

Parts diagrams →

Historical fitment & changes (7) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
111011121313141515161718192220212223242526273456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (27)

PosPart numberDescriptionQty
1 1121 020 2115 Crankcase Fitment / change note → 1
2 1121 020 2114 Crankcase Fitment / change note → 1
3 0000 988 5211 Connector 1
4 9416 868 6531 Hollow rivet 6.5x0.5x6.8 2
5 9371 470 2610 Cylindrical pin 5x18 2
6 0000 974 1200 Notched pin 2.6x8 1
7 1128 640 9100 Valve 1
8 9523 003 4260 Grooved ball bearing 15x35x13 1
9 9503 003 0320 Grooved ball bearing 16002 1
10 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 5
11 1120 162 5200 Pin 1
12 1121 162 5205 Pin 1
13 1121 162 5200 Pin 2
14 0000 664 2405 Collar screw M8 Fitment / change note → 1
15 1121 648 6610 Bumper strip Fitment / change note → 2
16 1121 021 1102 Cover Fitment / change note → 1
17 9022 313 0660 Spline screw IS-M4x12 2
18 1121 664 1000 Inner side plate Fitment / change note → 1
19 9039 488 0680 Self-tapping screw M4x16 Fitment / change note → 1
20 1121 660 3000 Tensioning gear Fitment / change note → 1
21 1121 664 7301 Nut M4 1
22 1121 640 1700 Chain sprocket cover Fitment / change note → 1
23 9076 478 2996 Pan head self-tapping screw P4x12 Fitment / change note → 1
24 1121 648 3800 Cover plate Fitment / change note → 1
25 1121 648 2200 NLA Adjusting wheel Fitment / change note → 1
26 1125 656 1501 Guard Fitment / change note → 1
27 1121 660 1000 Wing nut Fitment / change note → 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · 026 / MS 260

026 / MS 260: crankcases for clip cap and revised wiring

Ordinary and quick-tensioner crankcases have different replacement numbers.

  • Ordinary crankcase 1121 020 2112 changes to 1121 020 2117; the quick-chain-tensioner version changes from 1121 020 2114 to 1121 020 2115. Keep these configurations separate. Both previous versions remain available for older machines.
  • The revised cases have modified oil filler openings for the clip cap and changes for the ignition-lead routing. This is not a claim that an old cap, old wiring path or either crankcase variant can be freely mixed with the new configuration.
  • Shared IPL sheets do not extend these changes to unnamed variants. Introduction is in progress; the TI gives no numerical serial cutoff. Availability is the historical 2001 factory statement, not current stock. Later catalog numbers do not replace the historical evidence or prove unrestricted interchangeability.

Source: TI 43/2001, p. 4 · TI 43/2001, p. 5 · TI 43/2001, p. 7 · TI 43/2001, p. 8 — Section5, section7 routing context and summary rows22–23/remark1.

Part numbers (4)
  • 1121 020 2112 — Ordinary crankcasePrevious; retained · Only the named model/configuration; see conditions
  • 1121 020 2117 — Ordinary crankcaseNew · Only the named model/configuration; see conditions
  • 1121 020 2114 — Quick-chain-tensioner crankcasePrevious; retained · Only the named model/configuration; see conditions
  • 1121 020 2115 — Quick-chain-tensioner crankcaseNew · Only the named model/configuration; see conditions

Service note · 026 / 026 C

026 C: quick chain tensioner identification and locking function

The C identifies this convenience version; wheel, spiral gear and folding wingnut perform different functions.

  • The 026 C introduced here has a one-hand, tool-free chain tensioner and bar lock. C means a convenience feature, specifically the quick chain tensioner in this bulletin; it is not a universal meaning for C on every model. The cover photograph confirms the illustrated version, not a bar length, pitch or chain specification.
  • In 133TI035 KN, adjusting wheel (1) drives tensioning gear (2); its spiral groove and guides convert rotation into guide-bar travel. Turning the wheel forwards toward the bar nose moves the bar forwards and tensions the chain. Turning it counterclockwise (backwards, as printed) moves the bar back and slackens the chain.
  • Wingnut (3) locks the guide bar. Its handle (4) folds out for hand tightening; when folded flush, handle teeth (5) engage sprocket-cover teeth (6) to help prevent loosening. The wheel, wingnut and locking-element teeth are integrated into the sprocket cover. This function description is not a complete chain-tensioning safety procedure.
  • The first-in-the-world, maintenance-cost and time-saving statements are historical promotional claims, not independently verified performance or fitment evidence.
  • Historical TI 39/1998, series 1121 only. The 026 catalog binding locates the 026 C quick-chain-tensioner version described here; it does not extend these special parts to every 026, to an 024 quick-tensioner conversion or to MS 260 successors. Introduction was in progress; no serial threshold, current availability or measured physical interchange is established. No hardware operation was performed.

Source: TI 39/1998, p. 1 · TI 39/1998, p. 2 — Complete introduction/photo and section1; six callouts of133TI035 KN; section2 closing paragraph.

No additional parts-table entry added.

Conditional replacement · 026 / 026 C

026 C: quick tensioner retrofit requires a different crankcase

A sprocket-cover-only conversion is not supported: the crankcase must be replaced at the same time.

  • The 026 C quick-tensioner version uses a modified crankcase. Machines without this tensioner can be backfitted only if the crankcase is replaced at the same time. The TI therefore says there is no quick chain tensioner conversion kit; this is a 1998 supply statement, not proof about all later products.
  • Page3 item1 crankcase 1121 020 2114 includes item2, one M8 collar screw 0000 664 2405. Both carry remark1: replacement parts for machines with quick chain tensioner. All other crankcase parts are as before; that sentence does not waive the replacement-crankcase requirement or identify a complete conversion bill of materials.
  • The retained 2012 026 quick-tensioner sheet also lists crankcase 1121 020 2115. This TI does not explain that later number; no automatic supersession or reverse interchange is inferred.
  • Historical TI 39/1998, series 1121 only. The 026 catalog binding locates the 026 C quick-chain-tensioner version described here; it does not extend these special parts to every 026, to an 024 quick-tensioner conversion or to MS 260 successors. Introduction was in progress; no serial threshold, current availability or measured physical interchange is established. No hardware operation was performed.

Source: TI 39/1998, p. 2 · TI 39/1998, p. 3 — Section2 retrofit restriction; page3 items1–2,remark1 and all-other-parts statement.

Part numbers (2)
  • 1121 020 2114 — Crankcase; includes item2Required crankcase · 026 C with quick chain tensioner; TI 39/1998 only
  • 0000 664 2405 — Collar screw M8; one included with crankcaseIncluded component · 026 C with quick chain tensioner; TI 39/1998 only

Historical fitment · 026 / 026 C

026 C: bar support, side plate and crankcase bumper strips

The center screw clamps the bar; the other two collar screws resist twisting. The strips belong in the crankcase.

  • In 133TI036 KN, only center collar screw (1) secures the guide bar; the two collar screws (2) help prevent twisting. Hardened steel side plate (3) and two bumper strips (4) protect the crankcase from excessive wear. These are page2 figure numbers, not the page3 parts-table item numbers.
  • Page3 item3 lists two bumper strips 1121 648 6610. Remark2 explicitly locates them in the crankcase, NOT in the chain sprocket cover. Item5 inner side plate 1121 664 1000 carries quick-tensioner-only remark1; item6 self-tapping screw BM4x16 9039 488 0680 has no remark marker. The blank marker is not evidence of universal fitment.
  • The exploded drawing 133TI037 KN shows the strips above and below the bar-mount area, the separate cover, plate and screw. No extra part numbers are assigned to the two anti-twist collar screws from this figure alone.
  • Historical TI 39/1998, series 1121 only. The 026 catalog binding locates the 026 C quick-chain-tensioner version described here; it does not extend these special parts to every 026, to an 024 quick-tensioner conversion or to MS 260 successors. Introduction was in progress; no serial threshold, current availability or measured physical interchange is established. No hardware operation was performed.

Source: TI 39/1998, p. 2 · TI 39/1998, p. 3 — Section2 mounting/support bullets;133TI036 KN and133TI037 KN; items3,5–6,remarks1–2.

Part numbers (3)
  • 1121 648 6610 — Bumper strip; two, fitted in crankcaseHistorical component · 026 C with quick chain tensioner; TI 39/1998 only
  • 1121 664 1000 — Hardened inner side plate; remark1Historical component · 026 C with quick chain tensioner; TI 39/1998 only
  • 9039 488 0680 — Self-tapping screw BM4x16; item6 has no remark markerHistorical component · 026 C with quick chain tensioner; TI 39/1998 only

Conditional replacement · 024 / 026 / 026 C

024 / 026: guide-ledge cover 1121 021 1102 replaces 1101

The small cover with a molded guide ledge is the universal 024/026 replacement, not the complete quick-tensioner sprocket cover.

  • The integrally molded guide ledge (arrow in 133TI036 KN) eases assembly of the chain sprocket cover. Page3 item4 identifies this small cover as 1121 021 1102; remark3 permits it as a universal replacement for all model 024 and 026 saws in place of 1121 021 1101.
  • Do not transfer this compatibility claim to item9 chain sprocket cover 1121 640 1700, to the special crankcase or to the whole quick chain tensioner. The modified-crankcase retrofit requirement still applies. The reverse 1101-for-1102 direction is not established.
  • Historical all-024/026 wording is preserved; successor-model applicability is not inferred from shared series1121. The retained2012 026 quick-tensioner sheet provides a matching1102 row; the earlier1101 is retained as source evidence rather than silently deleted.
  • Historical TI 39/1998, series 1121: small-cover compatibility only. No serial threshold, reverse interchange, MS 240/MS 260 successor applicability or current supply is established. No hardware operation was performed.

Source: TI 39/1998, p. 2 · TI 39/1998, p. 3 — Section2 cover/arrow; page3 item4 and remark3.

Part numbers (2)
  • 1121 021 1101 — Previous small coverPrevious part · 024 / 026; replaced by1102 under remark3
  • 1121 021 1102 — Cover with integrally molded guide ledgeReplacement · All model024 and026 saws, per historical remark3

Historical fitment · 026 / 026 C

026 C: tensioning gear and historical M4x10 nut discrepancy

The 1998 assembly includes nut 9268 929 0650; the retained 2012 sheet lists a different nut, without an established relationship.

  • Page3 item7 tensioning gear 1121 660 3000 includes item8 nut M4x10 9268 929 0650. Both carry quick-tensioner remark1. Page2 calls the guide-bar attachment an M4x10 hexagon nut; preserve the printed description rather than silently changing it to a screw.
  • The exploded figure shows item8 at the guide-bar/tensioning-gear interface. The retained SCS01-2012 USA 026 quick-tensioner sheet instead lists nut M4 1121 664 7301 at position21. Different item numbering and the later number are not proof of supersession, dimensional equivalence or interchange. This discrepancy remains unresolved.
  • No tightening torque, thread specification beyond the printed M4x10, conversion recipe or separate fastener substitution is established by this TI.
  • Historical TI 39/1998, series 1121 only. The 026 catalog binding locates the 026 C quick-chain-tensioner version described here; it does not extend these special parts to every 026, to an 024 quick-tensioner conversion or to MS 260 successors. Introduction was in progress; no serial threshold, current availability or measured physical interchange is established. No hardware operation was performed.

Source: TI 39/1998, p. 2 · TI 39/1998, p. 3 — Section2 gear attachment; page3 items7–8 and remark1; bounded comparison to2012 catalog.

Part numbers (2)
  • 1121 660 3000 — Tensioning gear; includes item8Assembly · 026 C with quick chain tensioner; TI 39/1998 only
  • 9268 929 0650 — Nut M4x10 as printedIncluded historical nut · 026 C with quick chain tensioner; TI 39/1998 only

Historical fitment · 026 / 026 C

026 C: quick-tensioner sprocket-cover contents and separate wingnut

The 1998 cover assembly includes items10–13; wingnut item14 is listed separately.

  • Page3 item9 chain sprocket cover 1121 640 1700 includes items10 through13: PT4x12 screw 9076 478 2996, cover plate 1121 648 3800, adjusting wheel 1121 648 2200 and guard 1125 656 1501. The wingnut 1121 660 1000 is item14, outside that stated inclusion range.
  • Remark1 (quick-tensioner replacement only) marks items9,10,11,12 and14. Item13 guard has no marker; it remains listed in this assembly, not a new universal fitment claim. The figure shows the separate wingnut and all numbered parts, including the guard at the lower rear of the sprocket cover.
  • Introduction is printed as in progress, with no machine-number cutoff. Last-TI citations18.97 and39.97 (USA only), copyright1998 and footer6381 are bibliographic context, not additional production dates, component restrictions or source dependencies for these assertions. No current kit completeness is claimed.
  • Historical TI 39/1998, series 1121 only. The 026 catalog binding locates the 026 C quick-chain-tensioner version described here; it does not extend these special parts to every 026, to an 024 quick-tensioner conversion or to MS 260 successors. Introduction was in progress; no serial threshold, current availability or measured physical interchange is established. No hardware operation was performed.

Source: TI 39/1998, p. 2 · TI 39/1998, p. 3 — Section2 closing paragraph; full133TI037 KN; items9–14,remark1,introduction and footer.

Part numbers (6)
  • 1121 640 1700 — Chain sprocket cover; includes items10–13Assembly · 026 C with quick chain tensioner; TI 39/1998 only
  • 9076 478 2996 — Screw PT4x12; item10Included component · 026 C with quick chain tensioner; TI 39/1998 only
  • 1121 648 3800 — Cover plate; item11Included component · 026 C with quick chain tensioner; TI 39/1998 only
  • 1121 648 2200 — Adjusting wheel; item12Included component · 026 C with quick chain tensioner; TI 39/1998 only
  • 1125 656 1501 — Guard; item13, no remark markerIncluded component · 026 C with quick chain tensioner; TI 39/1998 only
  • 1121 660 1000 — Wingnut; item14Separately listed · 026 C with quick chain tensioner; TI 39/1998 only

Wrong number or missing part for the 026? Report a correction →