← 024 · 026 · MS 260 · MS 240

Stihl 1121 · Section G · 7 of 17 · 36 parts

Ignition system

Fits 026.

Parts diagrams →

Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314141515161616161617171818181922021232425262729330313233344456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (36)

PosPart numberDescriptionQty
1 1121 400 1200 Flywheel Fitment / change note → 1
2 1121 400 1207 Flywheel Fitment / change note → 1
3 1118 400 4000 NLA Generator Fitment / change note → 1
4 1118 431 6600 NLA Terminal pin Fitment / change note → no longer available from factory 1
5 1121 442 0402 NLA Insulating hose 35 mm / 1.4'' Fitment / change note → 1
6 9041 216 0540 NLA Pan head screw M3.5x12 3
7 1121 405 1900 NLA Support 1
8 9210 261 1140 Hexagon nut M8x1 1
9 0000 400 1300 Ignition module Fitment / change note → → replaced by 1122 400 1311, 0000 400 1305, 0000 400 1305 TI 51/1994 1
10 not sold separately Ignition lead 150 mm not available as a separate item 1
11 0000 989 1010 Grommet 1
12 0000 448 1250 Lead retainer 1
13 1121 440 3002 Wiring harness Fitment / change note → 1
14 0751 030 8957 Terminal socket 4.8-1/0.8 Fitment / change note → no longer available from factory 1
15 0751 030 8969 Terminal socket A5-1.5 Fitment / change note → no longer available from factory 1
16 1110 442 7000 NLA Contact sleeve Fitment / change note → no longer available from factory 2
17 0000 989 0507 Grommet Fitment / change note → 1
18 1125 442 0402 Insulating hose 90 mm / 3.5'' 1
19 1121 440 3003 NLA Wiring harness Fitment / change note → 1
20 1118 431 6700 NLA Terminal socket no longer available from factory 1
21 not sold separately Terminal socket not available as a separate item 1
23 1119 442 7000 Contact sleeve Fitment / change note → no longer available from factory 1
24 0751 030 8953 NLA Terminal socket 4.8-1 no longer available from factory 1
25 1121 405 8001 Insulating hose 90 mm / 3.5'' Fitment / change note → 1
26 not sold separately Lead 270 mm / 10.6'' not available as a separate item 1
27 0751 030 8969 Terminal socket A5-1.5 Fitment / change note → no longer available from factory 1
29 9022 341 1019 Spline screw IS-M5x20 2
30 1121 084 1410 Cover Fitment / change note → 1
31 1128 405 1000 Spark plug boot 1
32 0000 998 0604 Torsion spring 1
33 1106 405 1000 Spark plug boot → replaced by 1128 405 1000, 1128 405 1000 TI 30/1995 1
34 0000 998 0603 Torsion spring → replaced by 0000 998 0604 TI 30/1995 1
Not numbered on the diagram — assemblies, kits and options
— 0000 405 0600 NLA Ignition lead 1 m option 1
— 0000 930 2251 Ignition lead 10 m option 1
— 1121 007 1033 Ground wire kit 1
— 0751 010 1110 Lead 10 m / 33' 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · 026

026 VH: harness insulation and generator lead

The replacement harness and generator require source-specific preparation, routing and insulated connectors.

  • Harness 1121 440 3000 contains ground, short circuit and generator-connecting wires. At the fan housing it passes through insulating tube 1121 405 8001, diameter 9 mm. Grommet 0000 989 0507 serves the carburetor-box entry.
  • Tube 1121 442 0402 insulates both the generator-to-connecting-wire and connecting-wire-to-heater joints. The summary lists two 35 mm lengths. It is not interchangeable by inference with the separate diameter9mm fan-housing tube.
  • Before fitting the replacement harness, the source says cut off unnecessary wire (1) just behind the crimped joint in drawing133TI026 KN. The wire is identified by the original illustration, not by an invented color or electrical pinout; this is not an instruction to cut arbitrary harness wires.
  • The standard generator lead on carburetor-heated machines is 102 mm (4 inch), with a connector pin that mates to the harness terminal socket behind the ignition module. For replacement generator 1118 400 4000, shorten the lead to that length and attach terminal pin 1118 431 6600. No crimp-tool/die specification or strip length is provided here.
  • Push retainer (1) into the crankcase recess, place connection (2) as drawing133TI017 KN, completely cover connectors with the tube, then install the ignition module. Route the wire in crankcase slot (3), clear of the flywheel. Do not infer an ignition-module air gap, fastener torque or retainer ordering number.

Source: TI 12/1996, p. 3 · TI 12/1996, p. 5 — Sections2.3,2.4.1 and section2.5 items3,6–9.

Part numbers (6)
  • 1121 440 3000 — Wiring harnessReplacement preparation required · 026 VH
  • 1121 405 8001 — Insulating tube, diameter9mmFan-housing protection · 026 VH
  • 0000 989 0507 — GrommetCarburetor-box entry · 026 VH
  • 1121 442 0402 — Hose, two 35mm lengthsConnector insulation · Both heater circuit joints
  • 1118 400 4000 — GeneratorReplacement lead modification · 026 VH
  • 1118 431 6600 — Terminal pinReplacement-generator companion · 102mm generator lead

Conditional replacement · 024 / 026 / 028 / 029 / 034 / 036 / 038 / 039 / 048

024–048 listed saws: aluminium-flywheel ignition module split

024, 026, 028, 029, 034, 036, 038, 039 and 048 use optimized 0000 400 1300, not the former universal 1305 recommendation.

  • Applies only to the explicitly named 024, 026, 028, 029, 034, 036, 038, 039 and 048 aluminium-flywheel saws. The 044 and restricted 064 branches are separate records; a numeric span in the title does not include unnamed models.
  • The reactivated 0000 400 1300 number identifies the optimized aluminium-flywheel module here. The modified version has an integrated 400 mm (15 3/4 inch) ignition lead, no separate ignition lead and no short-circuit wire. The reused number alone does not distinguish all older constructions.
  • Only 0000 400 1300 is recommended for these machines. The permission to use existing 0000 400 1305 stock belongs to 046/066, not these models. No machine-number limit is supplied for these nine saws.
  • TI22/1998 reports isolated reliability problems with the former universal module on aluminium-flywheel machines. Different timing requirements led to two optimized modules; this is historical manufacturer field-test guidance, not a project hardware test.
  • Order only 0000 400 1300 or 1122 400 1314 according to the named model and restrictions. There is no automatic one-number replacement for 0000 400 1305.
  • The 02.98 microfiche/CD-ROM issue documents the future part numbers. Both summary rows say the original 0000 400 1305 is no longer available from the factory; that does not revoke the expressly permitted use of existing stocks on eligible 046/066 machines.
  • Introduction is in progress, without a new production cutoff. Factory availability is a 1998 statement, not current stock or proof of physical interchange.

Source: TI 22/1998, p. 1 · TI 22/1998, p. 2 — Sections 1–6: history, split, service note and ordering.

Part numbers (2)
  • 0000 400 1305 — Former universal ignition moduleEarlier recommendation · Named saws; superseded by model-specific guidance
  • 0000 400 1300 — Optimized aluminium-flywheel ignition moduleLater replacement · Only the nine explicitly named saw models

Historical fitment · 024 / 026

024 / 026: series 1121 replacement ignition assignment

0000 400 1300 and the listed flywheel pairings for series 1121; 150 mm ignition lead.

  • Standard: 0000 400 1300 with flywheel 1121 400 1200.
  • Heating: 0000 400 1300 with flywheel 1121 400 1207.
  • Printed ignition-lead length: 150 mm (5 7/8 in). Preserve the printed metric and inch values; no rounding correction is inferred.
  • TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
  • Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
  • Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
  • Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
  • Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.

Source: TI 1/1999, p. 1 · TI 1/1999, p. 2 — 1.1 general restrictions and 1.2.1 chainsaw assignments.

Part numbers (3)
  • 0000 400 1300 — Replacement ignition moduleAssigned replacement · 024 / 026, series 1121, only with the listed flywheel branch
  • 1121 400 1200 — Standard flywheelRequired pairing · 024 / 026, series 1121; standard only
  • 1121 400 1207 — Heating flywheelRequired pairing · 024 / 026, series 1121; heating only

Conditional replacement · 026 / MS 260

026 / MS 260: ignition-lead routing, harness and 44 mm cylinder

Routing changes involve the crankcase, shroud and cylinder; the second illustrated harness is not assigned a variant.

  • The ignition lead is carried in an insulating tube within the crankcase cable channel. A retainer near the annular-buffer mounting holds it in position. The shroud wall between carburetor box and cylinder has a molded guide; three cylinder fins were shortened to accommodate it. This describes the revised manufactured geometry, not an instruction to grind an old cylinder.
  • Short-circuit and ground wires are enclosed in shrink tube and routed as a harness to the carburetor box in an insulating tube. The yellow/green ground wire is secured by the lower ignition-module mounting screw.
  • The summary defines harness 1121 440 3002 as including cable lug 0751 030 8969 (A5-1.5, unchanged), contact sleeve 1110 442 7000 replacing 1119 442 7000, terminal socket 0751 030 8957 (4.8-1/0.8, unchanged), and insulating tube. The previous contact sleeve and 90 mm tube 1121 405 8001 remain available for older machines, but the new tube is not supplied separately and has no independent part number in this table.
  • The diagram additionally labels harness 1121 440 3003, but the TI does not assign its model/variant or list it in the summary. It is retained as an unassigned illustrated reference, not approved as a substitute for 1121 440 3002 or attributed to a heated variant.
  • For the explicitly named 026 and MS 260, the 44 mm cylinder with piston changes from 1121 020 1209 to 1121 020 1203. The previous version is supplied only while factory stocks last. The coordinated routing geometry does not establish universal component interchange.
  • Shared IPL sheets do not extend these changes to unnamed variants. Introduction is in progress; the TI gives no numerical serial cutoff. Availability is the historical 2001 factory statement, not current stock. Later catalog numbers do not replace the historical evidence or prove unrestricted interchangeability.

Source: TI 43/2001, p. 2 · TI 43/2001, p. 4 · TI 43/2001, p. 5 · TI 43/2001, p. 7 · TI 43/2001, p. 8 — Section7 routing and both harness drawings; summary rows28–32,38/remarks1–3.

Part numbers (9)
  • 1121 440 3002 — Wiring harnessSummary assembly including items29–32 · Only the named model/configuration; see conditions
  • 1121 440 3003 — Illustrated wiring harnessUnassigned diagram reference; no variant fitment established · No model/variant assigned by TI43
  • 0751 030 8969 — Cable lug A5-1.5Unchanged · Only the named model/configuration; see conditions
  • 1119 442 7000 — Contact sleevePrevious; retained · Only the named model/configuration; see conditions
  • 1110 442 7000 — Contact sleeveNew · Only the named model/configuration; see conditions
  • 0751 030 8957 — Terminal socket 4.8-1/0.8Unchanged · Only the named model/configuration; see conditions
  • 1121 405 8001 — Insulating tube 90 mmPrevious; retained · Only the named model/configuration; see conditions
  • 1121 020 1209 — 44 mm cylinder with pistonPrevious; stocks only · Only the named model/configuration; see conditions
  • 1121 020 1203 — 44 mm cylinder with pistonNew · Only the named model/configuration; see conditions

Service note · 024 / 026

024/026 spark-plug boot seal: production deletion, spare retained

Near-future deletion has no printed machine-number boundary.

  • Section 3 says seal 1121 084 1410 ON THE SPARK PLUG BOOT will be discontinued on the production line IN THE NEAR FUTURE, but remains available as a REPLACEMENT PART. The seal is not the spark-plug boot itself, and no replacement seal number is introduced.
  • The X 36 348 620 cutoff belongs to sections 1 and 2. Do NOT assign it to this undated future deletion. No instruction to remove seals from existing machines, current-stock promise or reason for deletion is stated.
  • Last Technical Information on models 024, 026: 38.96 is bibliographic context, not a delegated procedure. The four-page original has copyright 1997 and document number 6045, with no exact issue date printed. The retained catalogue title mentions Electric hand, but the original contents and section 3 concern the SPARK-PLUG BOOT SEAL; no electric-handle change is asserted by this TI.
  • Historical TI18/1997 evidence for 024 and 026 only, not MS240/MS260 or other successors. Model-sheet links aid discovery, not universal variant fitment. Factory supply statements describe the bulletin date, not current stock. No reciprocal interchange or physical verification inferred. No hardware operation was performed.

Source: TI 18/1997, p. 1 · TI 18/1997, p. 4 — 024/026 spark-plug boot seal: production deletion, spare retained.

Part numbers (1)
  • 1121 084 1410 — Seal on spark-plug bootProduction deletion announced; replacement retained · 024/026; 024/026 spark-plug boot seal: production deletion, spare retained; configuration restrictions in note

Wrong number or missing part for the 026? Report a correction →