Stihl 1121 · Section G · 7 of 17 · 27 parts
Ignition system
Fits MS 260, MS 260 C.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (27)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1121 400 1200 | Flywheel | 1 |
| 2 | 1121 400 1207 | Flywheel | 1 |
| 3 | 1118 400 4000 NLA | Generator | 1 |
| 4 | 1118 431 6600 NLA | Terminal pin no longer available from factory | 1 |
| 5 | 1121 442 0402 NLA | Insulating hose 35 mm / 1.4'' | 2 |
| 6 | 9041 216 0540 NLA | Pan head screw M3.5x12 | 3 |
| 7 | 1121 405 1900 NLA | Support | 1 |
| 8 | 9210 261 1140 | Hexagon nut M8x1 | 1 |
| 9 | 0000 400 1300 | Ignition module → replaced by 1122 400 1311, 0000 400 1305, 0000 400 1305 TI 51/1994 | 1 |
| 10 | not sold separately | Ignition lead 150 mm not available as a separate item | 1 |
| 11 | 0000 989 1010 | Grommet | 1 |
| 12 | 0000 448 1250 | Lead retainer | 1 |
| 13 | 1121 440 3002 | Wiring harness Fitment / change note → | 1 |
| 14 | 0751 030 8957 | Terminal socket 4.8-1/0.8 Fitment / change note → no longer available from factory | 1 |
| 15 | 0751 030 8969 | Terminal socket A5-1.5 Fitment / change note → no longer available from factory | 1 |
| 16 | 1110 442 7000 NLA | Contact sleeve Fitment / change note → no longer available from factory | 2 |
| 17 | 0000 989 0507 | Grommet | 1 |
| 18 | 1125 442 0402 | Insulating hose 90 mm / 3.5'' | 1 |
| 19 | 1121 440 3003 NLA | Wiring harness Fitment / change note → | 1 |
| 20 | 1118 431 6700 NLA | Terminal socket no longer available from factory | 1 |
| 21 | not sold separately | Terminal socket not available as a separate item | 1 |
| 22 | 1118 431 6600 NLA | Terminal pin no longer available from factory | 1 |
| 23 | 9022 341 1019 | Spline screw IS-M5x20 | 2 |
| 24 | 1128 405 1000 | Spark plug boot | 1 |
| 25 | 0000 998 0604 | Torsion spring | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 405 0600 NLA | Ignition lead 1 m option | 1 |
| — | 0000 930 2251 | Ignition lead 10 m option | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Conditional replacement · 026 / MS 260
026 / MS 260: ignition-lead routing, harness and 44 mm cylinder
Routing changes involve the crankcase, shroud and cylinder; the second illustrated harness is not assigned a variant.
- The ignition lead is carried in an insulating tube within the crankcase cable channel. A retainer near the annular-buffer mounting holds it in position. The shroud wall between carburetor box and cylinder has a molded guide; three cylinder fins were shortened to accommodate it. This describes the revised manufactured geometry, not an instruction to grind an old cylinder.
- Short-circuit and ground wires are enclosed in shrink tube and routed as a harness to the carburetor box in an insulating tube. The yellow/green ground wire is secured by the lower ignition-module mounting screw.
- The summary defines harness 1121 440 3002 as including cable lug 0751 030 8969 (A5-1.5, unchanged), contact sleeve 1110 442 7000 replacing 1119 442 7000, terminal socket 0751 030 8957 (4.8-1/0.8, unchanged), and insulating tube. The previous contact sleeve and 90 mm tube 1121 405 8001 remain available for older machines, but the new tube is not supplied separately and has no independent part number in this table.
- The diagram additionally labels harness 1121 440 3003, but the TI does not assign its model/variant or list it in the summary. It is retained as an unassigned illustrated reference, not approved as a substitute for 1121 440 3002 or attributed to a heated variant.
- For the explicitly named 026 and MS 260, the 44 mm cylinder with piston changes from 1121 020 1209 to 1121 020 1203. The previous version is supplied only while factory stocks last. The coordinated routing geometry does not establish universal component interchange.
- Shared IPL sheets do not extend these changes to unnamed variants. Introduction is in progress; the TI gives no numerical serial cutoff. Availability is the historical 2001 factory statement, not current stock. Later catalog numbers do not replace the historical evidence or prove unrestricted interchangeability.
Source: TI 43/2001, p. 2 · TI 43/2001, p. 4 · TI 43/2001, p. 5 · TI 43/2001, p. 7 · TI 43/2001, p. 8 — Section7 routing and both harness drawings; summary rows28–32,38/remarks1–3.
Part numbers (9)
- 1121 440 3002 — Wiring harnessSummary assembly including items29–32 · Only the named model/configuration; see conditions
- 1121 440 3003 — Illustrated wiring harnessUnassigned diagram reference; no variant fitment established · No model/variant assigned by TI43
- 0751 030 8969 — Cable lug A5-1.5Unchanged · Only the named model/configuration; see conditions
- 1119 442 7000 — Contact sleevePrevious; retained · Only the named model/configuration; see conditions
- 1110 442 7000 — Contact sleeveNew · Only the named model/configuration; see conditions
- 0751 030 8957 — Terminal socket 4.8-1/0.8Unchanged · Only the named model/configuration; see conditions
- 1121 405 8001 — Insulating tube 90 mmPrevious; retained · Only the named model/configuration; see conditions
- 1121 020 1209 — 44 mm cylinder with pistonPrevious; stocks only · Only the named model/configuration; see conditions
- 1121 020 1203 — 44 mm cylinder with pistonNew · Only the named model/configuration; see conditions
Wrong number or missing part for the MS 260, MS 260 C? Report a correction →