← 064/066 · MS 660 · MS 650/640

Stihl 1122 · Section G · 7 of 14 · 32 parts

Ignition system

Fits 064.

Parts diagrams →

Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1111213141516171819220202121222324252728293303132455666778889
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (32)

PosPart numberDescriptionQty
1 1122 400 1203 Flywheel Fitment / change note → 1
2 1122 400 1207 Flywheel Fitment / change note → 1
3 0000 955 0802 Collar nut M8x1 Fitment / change note → 1
4 0000 400 1300 Ignition module Fitment / change note → → replaced by 1122 400 1311, 0000 400 1305, 0000 400 1305 TI 51/1994 1
5 0000 989 1010 Grommet Fitment / change note → 1
6 not sold separately Ignition lead 185 mm not available as a separate item 1
7 0000 448 1250 Lead retainer 1
8 1117 442 0905 Insulating hose 110 mm / 4.3'' 1
9 9022 341 1019 Spline screw IS-M5x20 3
11 0000 998 0604 Torsion spring Fitment / change note → 1
12 1128 405 1000 Spark plug boot Fitment / change note → 1
13 1128 084 1400 Cover Fitment / change note → 1
14 1118 400 4000 NLA Generator 1
15 1118 431 6600 NLA Terminal pin no longer available from factory 1
16 9041 216 0540 NLA Pan head screw M3.5x12 3
17 1121 442 0402 NLA Insulating hose 35 mm / 1.4'' 1
18 1121 405 1900 NLA Support 1
19 1121 440 1103 Short circuit wire 305 mm / 12.1'' 1
20 1119 442 7000 Contact sleeve no longer available from factory 1
21 0751 030 8957 Terminal socket 4.8-1/0.8 no longer available from factory 1
22 1122 440 2201 Ground wire 270 mm / 10 5/8'' 1
23 0751 030 8955 Terminal socket 4.8-1/0.4 no longer available from factory 1
24 0751 030 8969 Terminal socket A5-1.5 no longer available from factory 1
25 1122 442 0400 Insulating hose 100 mm / 4'' 1
27 1122 448 1200 NLA Lead retainer Fitment / change note → 1
28 1122 084 1400 NLA Cover Fitment / change note → 1
29 1106 405 1000 Spark plug boot Fitment / change note → → replaced by 1128 405 1000, 1128 405 1000 TI 30/1995 1
30 0000 998 0603 Torsion spring Fitment / change note → → replaced by 0000 998 0604 TI 30/1995 1
31 not sold separately Ignition module no longer available from factory 1
32 1122 440 1100 NLA Short circuit wire 1
Not numbered on the diagram — assemblies, kits and options
— 0000 405 0600 NLA Ignition lead 1 m option 1
— 0000 930 2251 Ignition lead 10 m option 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · 064

064: original parts retained through the 066 revision

The summary preserves original crankshaft, seal and collar-nut versions as spares for 064; it does not approve new 066 parts.

  • Remark 3 applies to crankshaft item 2, seal item 4 and original collar-nut item 7: original versions remain available as spares for older machines and model 064.
  • The seal row places remark 3 beside the new seal, but the wording explicitly concerns the ORIGINAL version. Section 1.2 and rows 3–4 identify that original as BS 13.5×20×4, 9640 003 1355; the remark is not evidence that the larger seal fits 064.
  • No 064 production range, full crankcase interchange or new 066 crankshaft/flywheel fitment is established. This is historical spare retention, not present availability.

Source: TI 2/1996, p. 1 · TI 2/1996, p. 4 — Summary items 2,4,7 / remark 3 with original seal relationship in 1.2.

Part numbers (3)
  • 1122 030 0407 — Original crankshaftHistorical spare retention · 064 per remark 3
  • 9640 003 1355 — Original oil seal BS 13.5×20×4Historical spare retention · 064; original version specified by remark 3
  • 0000 955 0802 — Original collar nut M8×1Historical spare retention · 064 per remark 3

Conditional replacement · 064

064: replacement module requires the previous 1311 configuration

0000 400 1300 is limited to 064 machines previously equipped with 1122 400 1311; the printed threshold is not a universal model-identification range.

1 31 067 164 — TI22/1998 restriction on the previous 064 module configuration, not the introduction of the optimized replacement or a model-identification range.

  • Use of optimized 0000 400 1300 is limited to 064 machines previously equipped with 1122 400 1311, printed as from machine number 1 31 067 164, referring to TI51/1994. Check the actual previous-module configuration; the serial is not a blanket authorization for any machine above it.
  • The reactivated 0000 400 1300 number identifies the optimized aluminium-flywheel module here. The modified version has an integrated 400 mm (15 3/4 inch) ignition lead, no separate ignition lead and no short-circuit wire. The reused number alone does not distinguish all older constructions.
  • All other 064 machine numbers are directed to Spare Parts for Previous Models in the parts list. No module choice for those older configurations is inferred here. TI51/1994 is retained and separately queued, not semantically reviewed by this citation.
  • Existing 0000 400 1305 stock is not recommended for 064. The 046/066 stock permission does not override this 064 restriction.
  • TI22/1998 reports isolated reliability problems with the former universal module on aluminium-flywheel machines. Different timing requirements led to two optimized modules; this is historical manufacturer field-test guidance, not a project hardware test.
  • Order only 0000 400 1300 or 1122 400 1314 according to the named model and restrictions. There is no automatic one-number replacement for 0000 400 1305.
  • The 02.98 microfiche/CD-ROM issue documents the future part numbers. Both summary rows say the original 0000 400 1305 is no longer available from the factory; that does not revoke the expressly permitted use of existing stocks on eligible 046/066 machines.
  • Introduction is in progress, without a new production cutoff. Factory availability is a 1998 statement, not current stock or proof of physical interchange.

Source: TI 22/1998, p. 1 · TI 22/1998, p. 2 — Sections 1–6: history, split, service note and ordering.

Part numbers (3)
  • 0000 400 1305 — Former universal ignition moduleEarlier recommendation · Not the later recommended 064 choice
  • 0000 400 1300 — Optimized aluminium-flywheel ignition moduleRestricted replacement · 064 previously equipped with 1122 400 1311
  • 1122 400 1311 — Previous ignition moduleRequired prior configuration · 064 branch; from printed machine number 1 31 067 164

Historical fitment · 064

064: series 1122 replacement ignition assignment

0000 400 1300 and the listed flywheel pairing for series 1122; 205 mm ignition lead.

  • Listed configuration: 0000 400 1300 with flywheel 1122 400 1203.
  • Printed ignition-lead length: 205 mm (8 1/16 in). Preserve the printed metric and inch values; no rounding correction is inferred.
  • TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
  • Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
  • Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
  • Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
  • Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.
  • TI22/1998 separately restricts the 064 replacement to machines previously equipped with 1122 400 1311, printing 1 31 067 164. This later table does not explicitly revoke that previous-configuration restriction.

Source: TI 1/1999, p. 1 · TI 1/1999, p. 2 — 1.1 general restrictions and 1.2.1 chainsaw assignments.

Part numbers (2)
  • 0000 400 1300 — Replacement ignition moduleAssigned replacement · 064, series 1122, only with the listed flywheel branch
  • 1122 400 1203 — Listed configuration flywheelRequired pairing · 064, series 1122; listed configuration only

Service note · 064

064: CDIC to EY-V ignition and 75-degree terminal

Ungoverned EY-V uses revised terminal hardware; old components remain for older machines.

X 31 067 164 — Ignition and flywheel modification for 064/066 only; NOT the earlier carburetor cutoffs.

  • Section 1.1 replaces governed CDIC 1122 400 1303 with EY-V 1122 400 1311 WITHOUT electronic speed governor. Ignition leads, short circuit wires and spark plug terminals change. The 066-style 75° spark plug terminal, leg spring and cover standardize the 064.
  • Page 2 prints the 064 new-module entry as the incomplete “1122 400 131”; page 1 and the other EY-V rows explicitly print 1122 400 1311. Preserve this source truncation; use the complete number from those corroborating entries, not an invented padded number.
  • Both ignition modules include keys 1–2: cable retainer 1122 448 1200 becomes 1125 448 1201; grommet 0000 989 1010 is unchanged. Key 3 terminal 1106 405 1000 becomes 1128 405 1000; key 4 cover 1122 084 1400 becomes 1128 084 1400; key 5 leg spring 0000 998 0603 becomes 0000 998 0604. Original versions marked 1 remain available for older machines. All other parts as before.
  • Printed new-module MOQ is 1; terminal 1, cover 5 and leg spring 10. These are supply quantities, not five covers or ten springs on a saw.
  • The spline screw IS M5 x 20 remains 9022 371 1022, but remark 2 changes installed quantity from TWO to THREE. MOQ H is an order quantity, not an installed count; blank cells are not zero.
  • Converting CDIC/CDIC A to EY-V requires the NEW flywheel version and correct key slot (page 3); a module-only swap is not the printed conversion. The later 2012 ignition IPL uses other module/screw listings; no silent equivalence or supersession is inferred.
  • Historical TI 51/1994, dated December 15, 1994; not current stock, universal interchangeability or physical verification. No hardware operation was performed.

Source: TI 51/1994, p. 1 · TI 51/1994, p. 2 · TI 51/1994, p. 3 — 064: CDIC to EY-V ignition and 75-degree terminal.

Part numbers (12)
  • 1122 400 1303 — Original governed CDIC moduleolder machines · 064 only in the exact version/configuration described here
  • 1122 400 1311 — New ungoverned EY-V moduleincludes keys 1–2 · 064 only in the exact version/configuration described here
  • 1122 448 1200 — Original cable retainer; key 1older machines · 064 only in the exact version/configuration described here
  • 1125 448 1201 — New cable retainer; key 1included · 064 only in the exact version/configuration described here
  • 0000 989 1010 — Grommet; key 2unchanged · 064 only in the exact version/configuration described here
  • 1106 405 1000 — Original terminal; key 3older machines · 064 only in the exact version/configuration described here
  • 1128 405 1000 — 75-degree terminal; key 3MOQ 1 · 064 only in the exact version/configuration described here
  • 1122 084 1400 — Original cover; key 4older machines · 064 only in the exact version/configuration described here
  • 1128 084 1400 — New cover; key 4MOQ 5 · 064 only in the exact version/configuration described here
  • 0000 998 0603 — Original leg spring; key 5older machines · 064 only in the exact version/configuration described here
  • 0000 998 0604 — New leg spring; key 5MOQ 10 · 064 only in the exact version/configuration described here
  • 9022 371 1022 — Spline screw IS M5 x 20; key 6installed quantity 2 to 3 · 064 only in the exact version/configuration described here

Service note · 064 / 066

064 / 066: EY-V 900 rpm cut-in and exact air-gap requirement

Starting cut-in is not idle speed or maximum speed; this TI gives no numeric air-gap dimension.

  • New-module features: practically no backfiring, defined cut-in RPM, retarded timing during starting and idle for smoother idling, longer burning spark than CDIC/CDIC A for improved flame propagation, and reliable combustion during starting. These are historical manufacturer claims, not measurements reproduced here.
  • The footnote attributes backfire suppression to modified timing and a defined cut-in speed of 900 rpm. This is NOT an idle setting, electronic speed limit, or guarantee of zero backfire.
  • The air gap MUST be maintained exactly; too wide a gap prevents reaching the cut-in threshold. NO NUMERIC AIR GAP is printed. Do not derive an adjustment dimension from the schematic or a similar module.
  • Historical TI 51/1994, dated December 15, 1994; not current stock, universal interchangeability or physical verification. No hardware operation was performed.

Source: TI 51/1994, p. 2 — 064 / 066: EY-V 900 rpm cut-in and exact air-gap requirement.

Part numbers (1)
  • 1122 400 1311 — EY-V module900 rpm starting cut-in, not governed maximum · 064/066 only in the exact version/configuration described here

Service note · 064

064: EY-V flywheel revision and X/B versus P key slots

Unchanged part numbers conceal a changed slot position and magnet material; conversion needs the modified flywheel.

X 31 067 164 — Ignition and flywheel modification for 064/066 only; NOT the earlier carburetor cutoffs.

  • Introduction of EY-V changes the flywheel key-slot position AND magnet material. Replacement flywheels differ from production-line flywheels by having a SECOND key slot, marked P and X. Do not assume every production wheel has two slots.
  • For repair, use slot X (sometimes marked B on 064) for modules WITHOUT speed cut-off; use slot P for electronically governed CDIC/CDIC A. Figure 134TI001 shows both ignition categories pointing to their corresponding keyways; it does not provide timing degrees or a machining procedure.
  • If CDIC/CDIC A is exchanged for EY-V 1122 400 1311, the flywheel MUST be replaced by the NEW version and installed in the correct slot. A matching old part number alone does not establish the revised geometry or magnet material.
  • 064 standard flywheel 1122 400 1203 and heated-handle flywheel 1122 400 1207 keep their numbers. Only modified versions are available from the factory at the TI date. Standard and heated wheels remain distinct; blank MOQ cells do not specify zero.
  • The later 2012 IPL retains these historical numbers but also lists other ignition equipment. No later-part supersession, timing compatibility or MS 640/MS 660 applicability is established by this TI.
  • Historical TI 51/1994, dated December 15, 1994; not current stock, universal interchangeability or physical verification. No hardware operation was performed.

Source: TI 51/1994, p. 3 — 064: EY-V flywheel revision and X/B versus P key slots.

Part numbers (3)
  • 1122 400 1203 — Standard flywheelsame number; modified version only · 064 only in the exact version/configuration described here
  • 1122 400 1207 — Heated-handle flywheelsame number; modified version only · 064 only in the exact version/configuration described here
  • 1122 400 1311 — EY-V conversion modulerequires new flywheel version · 064 only in the exact version/configuration described here

Wrong number or missing part for the 064? Report a correction →