Stihl 1122 · Section M · 12 of 14 · 39 parts
Carburetor WJ-65A
Fits 064.
Historical fitment & changes (2) — includes parts and conditions not shown on this drawing.
Parts (39)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1122 121 5603 | Fixed jet 0.62 Fitment / change note → | 1 |
| 2 | 1110 121 5100 | Inlet needle | 1 |
| 3 | 1117 122 3005 | Spring | 1 |
| 4 | 1117 121 9200 | Spindle | 1 |
| 5 | 1117 121 5000 | Inlet control lever | 1 |
| 6 | 1114 122 7400 | Round head screw | 1 |
| 7 | 1115 121 5401 | Valve jet | 1 |
| 8 | 1122 121 0700 | Cup plug Fitment / change note → | 1 |
| 9 | 1116 129 0900 | Gasket | 1 |
| 10 | 1117 121 4700 | Metering diaphragm | 1 |
| 11 | 1122 121 0805 | End cover | 1 |
| 12 | 1121 122 7101 | Screw | 4 |
| 13 | 1115 121 3301 | Throttle shutter | 1 |
| 14 | 1115 122 7400 | Round head screw | 2 |
| 15 | 1128 122 3003 | Spring | 2 |
| 16 | 4203 122 3600 | Sealing ring | 2 |
| 17 | 1122 122 6802 | Low speed adjustment screw | 1 |
| 18 | 1122 122 6706 | High speed adjustment screw | 1 |
| 19 | 1122 121 7700 | Clamp | 1 |
| 20 | 1122 122 6200 | Idle speed adjustment screw | 1 |
| 21 | 1122 122 3200 | Torsion spring | 1 |
| 22 | 1122 120 7101 | Throttle shaft with lever | 1 |
| 23 | 1110 122 9300 | Clip | 1 |
| 24 | 1106 122 7400 | Round head screw | 1 |
| 25 | 1122 122 3205 | Torsion spring | 1 |
| 27 | 1117 122 9000 | E-clip | 1 |
| 28 | 1114 121 7800 | Strainer | 1 |
| 29 | 1115 121 4800 | Pump diaphragm | 1 |
| 30 | 1115 129 1100 | Gasket | 1 |
| 31 | 1115 120 0800 | End cover | 1 |
| 32 | 1121 122 7101 | Screw | 4 |
| 33 | 1122 121 2900 | Choke shutter | 1 |
| 34 | 1122 121 5608 NLA | Fixed jet 0.60 option | 1 |
| 35 | 1117 121 0800 NLA | End cover | 1 |
| 36 | 1116 122 9000 | E-clip | 1 |
| 37 | 1120 122 3600 NLA | Sealing ring | 1 |
| 38 | 1122 122 6705 | High speed adjustment screw Fitment / change note → | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1122 120 0616 | Carburetor WJ-65A Fitment / change note → → replaced by 1122 120 0621, 1122 120 0618 TI 1/1998 | 1 |
| — | 1122 007 1060 | Set of carburetor parts | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · 064
064: WJ 41 to WJ 48 carburetor
EY-V adaptation changes fixed jet, high-speed screw and cup plug; carburetor introduction precedes ignition.
X 30 982 432 — 064 adapted carburetor only; not the ignition/flywheel cutoff or a model-production range.
- Page 4 assigns WJ 48 to 064. The table replaces WJ 41 1122 120 0607 with WJ 48 1122 120 0616; both assembly headings say they include items 1–4. New complete carburetor MOQ 1. No new interchangeable repair-kit number is given.
- Fixed jet 0.72 mm 1122 121 5602 becomes 0.62 mm 1122 121 5603. High speed adjusting screw 1122 122 6702 becomes 1122 122 6705. Cup plug 1115 121 0700 becomes 1122 121 0700. All three old component types remain available for older machines (remark 2); each new component has MOQ 1.
- Figure 134TI002 identifies the fixed-jet marking 62 for WJ 48 and 64 for WJ 51/52. Those markings represent 0.62/0.64 mm jets, not 62/64 mm bores or carburetor identities by themselves.
- Original WJ 41 has remark 1: no longer available from factory.
- Carburetor cutoff X 30 982 432 is for 064; page 4 prints only the 064 cutoff, while page 5 supplies BOTH model cutoffs. Neither equals ignition/flywheel cutoff X 31 067 164. Do not rewrite the earlier carburetor introduction to make a single simultaneous conversion boundary.
- The exact-model 2012 carburetor sheet is a navigation context, NOT identification with its later WJ-65A/WJ-67A/WJ-76A configurations. In particular 1122 120 0616 is labeled WJ 48 here but WJ-65A in the later IPL; the shared number does not prove identical calibration or supersession. Preserve the historical jet/screw assignments; no complete current tuning or retrofit procedure is supplied.
- Historical TI 51/1994, dated December 15, 1994; not current stock, universal interchangeability or physical verification. No hardware operation was performed.
Source: TI 51/1994, p. 4 · TI 51/1994, p. 5 — 064: WJ 41 to WJ 48 carburetor.
Part numbers (8)
- 1122 120 0607 — Original WJ 41 carburetororiginal; availability as qualified · 064 only in the exact version/configuration described here
- 1122 120 0616 — New WJ 48 carburetorincludes items 1–4; MOQ 1 · 064 only in the exact version/configuration described here
- 1122 121 5602 — Original fixed jet 0.72 mmolder machines · 064 only in the exact version/configuration described here
- 1122 121 5603 — New fixed jet 0.62 mmMOQ 1 · 064 only in the exact version/configuration described here
- 1122 122 6702 — Original high-speed screwolder machines · 064 only in the exact version/configuration described here
- 1122 122 6705 — New high-speed screwMOQ 1 · 064 only in the exact version/configuration described here
- 1115 121 0700 — Original cup plugolder machines · 064 only in the exact version/configuration described here
- 1122 121 0700 — New cup plugMOQ 1 · 064 only in the exact version/configuration described here
Service note · 064 / 066
064 / 066: revised 13000 rpm maximum with bar and chain
The historical maximum is measured with guide bar and properly tensioned chain, not as a bare-powerhead speed.
- Maximum permissible speed changes: 064 from 12,000 to 13,000 rpm; 066 CDIC A from 13,500 rpm CUT-OFF speed to 13,000 rpm; 066 USA/CDN from 13,500 to 13,000 rpm. These old values belong to their named ignition variants; do not infer that all original modules had electronic governors.
- ALL engine speeds are measured with GUIDE BAR and PROPERLY TENSIONED CHAIN. This is not a bare-powerhead limit or a replacement for exact-version servicing instructions. The ungoverned EY-V has no implied automatic 13,000 rpm limiter.
- The separate 900 rpm ignition cut-in is not an idle speed. No idle setting, H-screw turns or target-specific numerical air gap is supplied. No engine was run or adjusted.
- Footer refers to previous TI 45.94 on 064/066 and is dated December 15, 1994. This is a prior-information pointer, not a required missing retrofit document or proof of blanket later-model applicability.
- Historical TI 51/1994, dated December 15, 1994; not current stock, universal interchangeability or physical verification. No hardware operation was performed.
Source: TI 51/1994, p. 4 · TI 51/1994, p. 5 — 064 / 066: revised 13000 rpm maximum with bar and chain.
No additional parts-table entry added.
Wrong number or missing part for the 064? Report a correction →