← 064/066 · MS 660 · MS 650/640

Stihl 1122 · Section N · 13 of 14 · 34 parts

Shroud, Air filter

Fits 064.

Parts diagrams →

Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161718192202122232324252627282933031324567889
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (34)

PosPart numberDescriptionQty
1 1122 080 1603 Shroud → replaced by 1122 080 1608 TI 1/2003 1
2 1122 967 1503 Model plate 064 Fitment / change note → 1
3 1125 080 8000 Shutter 1
4 9646 945 0590 O-ring 8x2 1
5 9099 021 3760 Self-tapping screw 4.8x13 1
6 1121 084 7100 Cap 1
7 1124 084 8300 Reflector foil 1
8 9022 341 0980 Spline screw IS-M5x16 3
9 1122 121 7000 NLA Baffle 1
10 1122 120 1621 NLA Air filter 1
11 1122 120 4101 NLA Baffle 1
12 1124 141 8300 Slotted nut 2
13 1122 122 6605 NLA Collar screw 1
14 1122 120 1615 NLA Air filter 1
15 1128 129 1100 Gasket 1
16 1122 120 3411 Filter base Fitment / change note → 1
17 9121 319 0960 Stud M5x12x9 Fitment / change note → 1
18 9216 261 0700 Hexagon nut M5 2
19 0000 140 4402 Air filter HD2 1
20 0000 124 0800 Filter insert Fitment / change note → 1
21 0000 141 0300 Prefilter Fitment / change note → 1
22 1122 140 1001 Filter cover 1
23 1124 140 9500 Twist lock 1
24 1122 140 1900 NLA Carburetor box cover 1
25 1122 140 1901 Carburetor box cover option 1
26 1122 141 2500 Cover option 1
27 9438 929 4040 NLA Blind rivet 5x8 option 4
28 1122 084 8206 Cover plate → replaced by 1122 084 8207 TI 1/1998 option 1
29 9022 313 0660 Spline screw IS-M4x12 option 3
30 0000 120 1601 Air filter, fleece option 1
31 0000 141 0600 Prefilter option 1
32 0000 124 1000 Supporting plate option 1
Not numbered on the diagram — assemblies, kits and options
— 1122 007 1031 NLA Air filter kit HD Fitment / change note → option 1
— 0000 120 1655 Air filter option 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · 044 / 064 / 066 / 084

044 / 064 / 066 / 084: dry HD filter requires inner foam

Dry fleece replacement, cleaning and model-specific foam rule.

Later reviewed guidance: 066 new filter system: winter mesh, dry HD and foam scope

  • Dry fleece HD filter 0000 120 1652 replaces oil-impregnated HD filter 0000 120 1650. The new filter carries the crossed-out OIL pictogram and does not need oil impregnation. This is not a blanket no-oil rule for the original filter or unrelated filter materials.
  • When cutting power noticeably drops, clean felt prefilter 0000 141 0300. After several prefilter cleanings, or if power remains low with a clean prefilter, remove the felt prefilter and clean the HD filter; carefully blow from the clean-air side if possible. On 044/064/066/084 also remove inner foam 0000 124 0800 for cleaning.
  • For stubborn dirt or caked fleece, wash filter parts in a clean non-flammable solution, such as warm soapy water. No air-pressure value, solvent recipe, drying duration or oiling step is supplied by this bulletin.
  • Fine trapped dirt may remain after cleaning and shorten cleaning intervals with extended use. Replace the filter when those intervals are no longer practical, or if thorough cleaning after long operation still leaves a noticeable cutting-power loss. No fixed service-hour limit or diagnosis excluding other causes is established.
  • Introduction is in progress, without a numeric cutoff. Original filter 0000 120 1650 was no longer supplied by the factory in this historical source, not a present stock assertion. An included instruction sheet is mentioned but is not reproduced or claimed reviewed here; the printed bulletin procedures above stand on their own.
  • Inner foam element 0000 124 0800 is included in the supplied HD filter and is required for 044, 064, 066 and 084. Refit the applicable inner foam after cleaning; the 046/088 removal rule does not apply to these models.
  • No later MS-model, every air-filter system or physical interchange claim is inferred from the shared part number.

Source: TI 43/1996, p. 1 · TI 43/1996, p. 2 — Both complete pages: dry fleece identification, cleaning, service life, installation and supply summary.

Part numbers (4)
  • 0000 120 1650 — Oil-impregnated HD air filterOriginal · 044 / 064 / 066 / 084
  • 0000 120 1652 — Dry fleece HD air filterReplacement · 044 / 064 / 066 / 084
  • 0000 141 0300 — Felt prefilterCleaning subject · 044 / 064 / 066 / 084
  • 0000 124 0800 — Inner foam elementRequired · 044 / 064 / 066 / 084

Conditional replacement · 064 / 066

064 / 066: modified HD filter needs the old gasket removed

From X 31 067 595: remove gasket 1124 129 0900 before the modified HD element; oil before first use, foam inside, felt TOP outward.

X 31 067 595 — Modified HD filter introduction on explicitly named 064/066 only; not a cylinder changeover or universal model-identification range.

  • The modified HD filter replaces the original metal version with an integrally molded rubber cover and TWO peripheral elastomer sealing lips. The TI states improved sealing between base and cover and filtration in fine dust; these are historical design claims, not measured filtration performance.
  • Before installing the new filter element, REMOVE original gasket 1124 129 0900 from the filter base. Its deletion from the new assembly is NOT universal spare unavailability: remark 4 explicitly retains it as a spare. This TI does not state a reverse-conversion procedure or extend the rule to later HD2 filters.
  • Illustration 132BB001: impregnate the filter element with STIHL HD filter oil BEFORE first installation.132BB002: fit the foam insert IN the HD filter.132BB003: fit felt prefilter 0000 141 0300 OVER the filter, with TOP pointing OUTWARD, then check seating. The felt is designed to sit firmly on the element. No oil quantity, oil order number or cleaning interval is given.
  • Follow the fitting and maintenance instructions supplied in the separate detailed HD-kit information sheet. That exact insert was not identified in the reviewed collection; this note retains the TI instructions but is NOT a complete substitute for the insert. No successor kit instructions are silently substituted.
  • The later 064/066 IPL sheets list HD2 filter 0000 140 4402 and optional air filter 0000 120 1655. These differ from complete HD filter 0000 120 1650 here; no equivalence, supersession or inheritance of the oiling procedure is inferred. The later 066 sheet still lists gasket 1124 129 0900; that does not override the modified-filter removal condition.
  • Historical TI guidance for the explicitly named models only; exact-model IPL links are navigation, not proof of unrestricted interchange. No hardware operation was performed.

Source: TI 10/1995, p. 1 · TI 10/1995, p. 2 — Sections 1–2: complete two pages, illustrations 132BB001–003 and 137TI002, full summary and remarks.

Part numbers (4)
  • 1124 129 0900 — Original filter-base gasket / sealing ringremove for modified filter; remains spare · 064; 066; stated TI conditions
  • 0000 120 1650 — Complete HD filternew historical complete assembly · 064; 066; stated TI conditions
  • 0000 124 0800 — Foam filter insertinside HD filter · 064; 066; stated TI conditions
  • 0000 141 0300 — Felt prefilteroutside HD filter; TOP outward · 064; 066; stated TI conditions

Conditional replacement · 064 / 066

064 / 066: unchanged HD-kit number, revised contents

Kit 1122 007 1031 keeps its number; only its modified version is supplied. New bare elements are not separately available.

X 31 067 595 — Modified HD filter introduction on explicitly named 064/066 only; not a cylinder changeover or universal model-identification range.

  • Complete HD filter 0000 120 1650 (MOQ 1) includes keys 1–3: element, foam insert and felt prefilter. Original element 1124 120 1620 is replaced by a new element marked -*-; remark 1 says the NEW element is not available separately. No standalone new-element number or old-element availability is invented.
  • Keys 2/10: insert 1124 124 0804 becomes 0000 124 0800 (MOQ 10). Keys 3/11: prefilter 1124 141 0301 becomes 0000 141 0300 (MOQ 1). Originals are supplied ONLY until stocks are exhausted (remark 2); MOQ 10 is an ordering minimum, not ten installed inserts.
  • Key 4: HD air filter kit 1122 007 1031 keeps the SAME number in both columns; remark 3 means only its modified version is supplied. The table labels kit contents keys 5–12, while key 8 sealing ring 1124 129 0900 is explicitly deleted on the NEW side. The original key range does NOT reintroduce that ring into the modified kit.
  • Key 5 gasket 1122 129 1100 unchanged; key 6 filter base 1122 120 3410 becomes 1122 120 3411 (MOQ 1, old stock exhausted under remark 2), including key 7 stud 9121 319 0960, unchanged. Keys 9–11 repeat the element/insert/prefilter changes above; key 12 cover 1122 140 1000 unchanged. All other parts as before. Blank MOQ/remark cells do not imply zero or an unstated supply rule.
  • The table calls the unchanged stud M5 x 12 x 10; both later exact-model IPLs call the SAME 9121 319 0960 number M5x12x9. This dimensional-description conflict is preserved, not corrected by assumption. Later 064 gasket 1128 129 1100, covers 1122 140 1001(064)/1002(066), and 066 base 1122 120 3402 also differ; no equivalence or supersession follows from this TI.
  • Both introduction statements print X 31 067 595 for the HD change only. Last TI 51.94 is bibliographic. Footer: Waiblingen, March 06, 1995; ©1995 Andreas Stihl; D1/MTK-al, Technical Documentation. Issue 10.95 is not an October production date.
  • Historical TI guidance for the explicitly named models only; exact-model IPL links are navigation, not proof of unrestricted interchange. No hardware operation was performed.

Source: TI 10/1995, p. 1 · TI 10/1995, p. 2 — Sections 1–2: complete two pages, illustrations 132BB001–003 and 137TI002, full summary and remarks.

Part numbers (13)
  • 0000 120 1650 — HD filter complete; includes 1–3new; MOQ 1 · 064; 066; stated TI conditions
  • 1124 120 1620 — Original HD filter element; keys 1/9new element not supplied separately · 064; 066; stated TI conditions
  • 1124 124 0804 — Original filter insert; keys 2/10available until stocks exhausted · 064; 066; stated TI conditions
  • 0000 124 0800 — New filter insert; keys 2/10MOQ 10 · 064; 066; stated TI conditions
  • 1124 141 0301 — Original felt prefilter; keys 3/11available until stocks exhausted · 064; 066; stated TI conditions
  • 0000 141 0300 — New felt prefilter; keys 3/11MOQ 1 · 064; 066; stated TI conditions
  • 1122 007 1031 — HD air filter kit; key 4unchanged number; modified version only · 064; 066; stated TI conditions
  • 1122 129 1100 — Gasket; key 5unchanged · 064; 066; stated TI conditions
  • 1122 120 3410 — Original filter base; key 6available until stocks exhausted · 064; 066; stated TI conditions
  • 1122 120 3411 — New filter base; key 6MOQ 1; includes stud 7 · 064; 066; stated TI conditions
  • 9121 319 0960 — Stud M5 x 12 x 10 as printed; key 7unchanged; later IPL says M5x12x9 · 064; 066; stated TI conditions
  • 1124 129 0900 — Sealing ring; key 8deleted from new assembly; remains spare · 064; 066; stated TI conditions
  • 1122 140 1000 — Filter cover; key 12unchanged · 064; 066; stated TI conditions

Service note · 064 / 066

064 / 066: dry fleece HD filter at X 36 262 047

Do not oil the new fleece; preserve the earlier-system inner-foam requirement.

Later reviewed guidance: 066 new filter system: winter mesh, dry HD and foam scope

X 36 262 047 — Dry-fleece HD filter change for 064/066; not later 066 flange/foam deletion.

  • From X 36 262 047, dry-fleece HD filter 0000 120 1652 replaces original HD filter 0000 120 1650, which needs oil impregnation. The new fleece is designed to filter WITHOUT OIL and MUST NOT be impregnated with oil. This no-oil rule is material-specific, not permission to leave the original oil-treated filter dry.
  • The explicit See also TI43/1996 dependency is already reviewed. That source requires inner foam 0000 124 0800 on 064/066 and describes cleaning felt prefilter0000 141 0300 and HD filter. Reuse its exact configuration-specific guidance; dry fleece does not mean omit inner foam.
  • Later TI01/1998 omits foam only for the revised 066 flange/baffle arrangement from X 39 176 186, as documented in the linked later note. That later exception does not apply automatically at this earlier filter cutoff or to 064. Unchanged filter number does not identify the surrounding filter system.
  • Historical TI08/1997 evidence for the stated 064/066 configurations only. Independent modification cutoffs are not whole-model identification ranges, current stock claims or blanket retrofit permission. No MS640/MS660 successor scope or tested physical interchange is inferred. No hardware operation was performed.

Source: TI 8/1997, p. 2 — 064 / 066: dry fleece HD filter at X 36 262 047.

Referenced bulletin evidence: TI 43/1996, p. 1 · TI 43/1996, p. 2 — Both complete pages: dry fleece identification, cleaning, service life, installation and supply summary.

Part numbers (4)
  • 0000 120 1650 — Original oil-impregnated HD filterOriginal · 064 / 066; only the described configuration
  • 0000 120 1652 — New dry-fleece HD filterReplacement; do not oil · 064 / 066; only the described configuration
  • 0000 124 0800 — Inner foam for earlier 064/066 systemRequired companion from referenced TI43/1996 · 064 / 066; only the described configuration
  • 0000 141 0300 — Felt prefilterCleaning subject from referenced TI43/1996 · 064 / 066; only the described configuration

Service note · 064

064: plastic nameplate requires countersunk shroud holes

Original aluminium nameplates and two rivets remain replacements for older shrouds.

X 33 459 523 — Nameplate and prepared-shroud change only.

  • From X 33 459 523, riveted aluminium 064 nameplate1122 967 1502 changes to clip-in plastic1122 967 1503. New plate pushes into the carburetor-box cover and is retained by TWO LUGS; the shroud has two COUNTERSUNK holes.
  • Plastic plates CANNOT be fitted to the original shroud because its mounting holes are not countersunk. Original aluminium plates and round-head rivets remain available for older machines. This is not an instruction to countersink or modify the old shroud.
  • Each original nameplate listing includes TWO round-head rivets3x6,0000 974 1000. New rivet column is a dash because plastic retention uses lugs; no replacement rivet number or universal plate interchange is invented.
  • Historical TI08/1997 evidence for the stated 064/066 configurations only. Independent modification cutoffs are not whole-model identification ranges, current stock claims or blanket retrofit permission. No MS640/MS660 successor scope or tested physical interchange is inferred. No hardware operation was performed.

Source: TI 8/1997, p. 3 — 064: plastic nameplate requires countersunk shroud holes.

Part numbers (3)
  • 1122 967 1502 — 064 aluminium nameplateOriginal; retained for older machines · 064; only the described configuration
  • 1122 967 1503 — 064 plastic nameplateNew; requires countersunk shroud · 064; only the described configuration
  • 0000 974 1000 — Round-head rivet3x6, two per original plateOriginal retention; new column dash · 064; only the described configuration

Wrong number or missing part for the 064? Report a correction →