← 064/066 · MS 660 · MS 650/640

Stihl 1122 · Section N · 13 of 17 · 45 parts

Handlebar (Heating)

Fits 066.

Parts diagrams →

Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111212131415161718192202223242526272829333330313233343536363738394444404142434456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (45)

PosPart numberDescriptionQty
1 1122 790 1752 Handlebar 1
2 1124 442 0400 NLA Insulating hose 160 mm / 6.3'' 1
3 1118 431 6700 NLA Terminal socket no longer available from factory 1
4 0000 442 7000 NLA Contact sleeve no longer available from factory 1
5 9074 478 4475 Pan head self-tapping screw IS-P6x21.5 2
6 9074 478 4435 Pan head self-tapping screw IS-P6x19 2
7 1122 790 1751 Handlebar 1
8 1124 791 5105 Stiffener 1
9 9074 478 4675 Pan head self-tapping screw IS-P6x32.5 2
10 1122 790 3610 Wrap around handlebar 1
11 1122 790 3604 Wrap around handlebar Fitment / change note → → replaced by 1122 790 3607 TI 2/1996 1
12 1121 442 0403 Insulating hose 130 mm / 5.1'' 1
13 9307 021 0120 Washer 5.3 1
14 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 1
15 1122 791 5501 Elbow connector 1
16 1122 791 5500 Elbow connector → replaced by 1122 790 3610, 1122 791 5501 TI 10/2008 1
17 9074 478 4435 Pan head self-tapping screw IS-P6x19 1
18 9074 478 4435 Pan head self-tapping screw IS-P6x19 2
19 9074 478 4475 Pan head self-tapping screw IS-P6x21.5 1
20 9074 478 4675 Pan head self-tapping screw IS-P6x32.5 1
22 9074 478 2970 Pan head self-tapping screw IS-P4x10 1
23 0000 989 0808 Grommet 1
24 0000 989 0813 NLA Grommet 1
25 1121 442 0406 NLA Insulating hose 40 mm / 1.6'' 1
26 1110 432 9200 Grommet 1
27 1110 430 0202 Stop switch 1
28 1122 431 2700 NLA Twin connector tag 1
29 0000 961 1406 NLA Ring 1
30 0000 958 1406 NLA Washer 1
31 1118 432 2200 NLA Hexagon nut M12 1
32 1122 440 2205 NLA Ground wire 1
33 0751 030 8953 NLA Terminal socket 4.8-1 no longer available from factory 2
34 1121 791 9000 NLA Clamp 1
35 1128 434 5000 NLA Heating element Fitment / change note → 1
36 1118 431 6600 NLA Terminal pin no longer available from factory 1
37 1125 434 5000 NLA Heating element Fitment / change note → 1
38 1121 442 0402 NLA Insulating hose 35 mm / 1.4'' Fitment / change note → 2
39 not sold separately Wrap around handlebar optionno longer available from factory 1
40 1121 442 0403 Insulating hose 130 mm / 5.1'' option 1
41 1122 791 4500 Spacer option 1
42 9074 478 4705 Pan head self-tapping screw IS-P6x40 option 2
43 9074 478 4435 Pan head self-tapping screw IS-P6x19 option 2
44 1124 890 3400 NLA Combination wrench option 1
Not numbered on the diagram — assemblies, kits and options
— 1122 790 3651 Wrap around handlebar 1
— 1122 007 1022 Set wrap around handlebar option 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · 066

066: generator revision supports combined heating

Generator 1128 404 3501 replaces 1122 404 3500 with the lightweight-flywheel modification.

X 33 917 066 — Introduction of this 066 wrap-handle modification; not a model-identification range or a cutoff for the standard flush-cut version.

  • The higher-output generator permits handle heating and carburetor heating together. The bulletin gives no numeric electrical output, connector interchange test or stand-alone retrofit permission.
  • Introduction belongs to the wrap-handle engine/ignition modification. The crankcase generator seat also changes; matching the complete configuration remains required.
  • Summary remark 1 keeps the original generator available historically as a spare for older machines. This is not current availability or permission to mix old and new assemblies.

Source: TI 2/1996, p. 2 · TI 2/1996, p. 4 — 2.3 and summary item 10 / remark 1.

Part numbers (2)
  • 1122 404 3500 — Original generatorOriginal version · Older 066 configuration
  • 1128 404 3501 — Higher-output generatorNew version · Revised 066 configuration with combined heating capability

Historical fitment · 066

066: keep the three heating-harness branches distinct

The combined-heating harness changes, while handle-heating-only harness 1122 440 3007 continues.

X 33 917 066 — Introduction of this 066 wrap-handle modification; not a model-identification range or a cutoff for the standard flush-cut version.

  • Wiring harness 1122 440 3009 replaces carburetor-heating version 1122 440 3008 and can serve machines with both handle and carburetor heating.
  • Original harness 1122 440 3008 remains available for machines up to X 33 917 065. That inclusive old-machine boundary is separate from the new modification beginning at X 33 917 066.
  • Handle-heating-only machines continue to use 1122 440 3007. Do not substitute the combined-heating harness solely because the model name is 066.
  • The drawing shows harness layout, but does not provide a complete wiring diagram, pinout or electrical test procedure.

Source: TI 2/1996, p. 3 · TI 2/1996, p. 4 — 3 and summary item 13 / remark 1.

Part numbers (3)
  • 1122 440 3008 — Original carburetor-heating harnessRetained older-machine spare · Up to X 33 917 065
  • 1122 440 3009 — Combined-heating harnessRevised version · Handle AND carburetor heating
  • 1122 440 3007 — Handle-heating-only harnessUnchanged branch · Handle heating only

Historical fitment · 066

066: identify revised heaters by resistance at 25°C

Higher-resistance front and rear heaters accompany the revision; the nonheated wrap handle is unchanged.

X 33 917 066 — Introduction of this 066 wrap-handle modification; not a model-identification range or a cutoff for the standard flush-cut version.

  • Heated front handle 1122 790 1712 changes to 1122 790 1713. Wrap-around handle for handle AND carburetor heating changes from 1122 790 3604 to 1122 790 3607. Both new handle versions have higher-resistance heating elements.
  • Wrap-around handle 1122 790 3603 continues for machines with neither handle nor carburetor heating; it is not one of the heated replacement handles.
  • At +25°C (77°F), front-handle heating-element resistance is 1.44–1.76 Ω original and 6.3–7.7 Ω new. Rear-handle element resistance is 0.225–0.275 Ω original and 0.9–1.1 Ω new. These values are component- and temperature-specific, not whole-circuit limits.
  • Rear element 1128 434 5000 replaces 1125 434 5000. The new element has thinner printed conductors running in wavy lines; the diagram identifies original on the left and new on the right.
  • Original heated handles and rear element remain historical spares for older machines under remark 1, subject to the flywheel pairing restrictions. This 066 resistance table does not silently resolve the separate unit conflict in TI07/1995 for 044.

Source: TI 2/1996, p. 3 · TI 2/1996, p. 4 — 4.1–4.3 and summary items 14–16 / remark 1.

Part numbers (7)
  • 1122 790 1712 — Original heated front handleOriginal heater · 066 handle heating
  • 1122 790 1713 — Revised heated front handleHigher-resistance heater · 066 handle heating
  • 1122 790 3604 — Original heated wrap handleOriginal heater · 066 handle and carburetor heating
  • 1122 790 3607 — Revised heated wrap handleHigher-resistance heater · 066 handle and carburetor heating
  • 1122 790 3603 — Nonheated wrap handleUnchanged · Neither handle nor carburetor heating
  • 1125 434 5000 — Original rear heating elementOriginal heater · Old flywheel pairing only
  • 1128 434 5000 — Revised rear heating elementHigher-resistance heater · New heated-flywheel configuration

Historical fitment · 066

066: heated-flywheel retrofit requires both heater changes

Installing flywheel 1122 400 1218 on an older saw requires the new rear element and the revised front or wrap handle.

  • For a saw up to X 33 917 065 receiving flywheel 1122 400 1218, bond rear heating element 1128 434 5000 into the rear handle AND replace the original front/wrap handle with the new higher-resistance version. Identify front-handle versions by the +25°C resistance table.
  • This heating note does not waive the new-flywheel requirement for a matching new crankshaft and crankcase or matching ignition module. It is not permission to fit the new flywheel alone.
  • The source warns that new flywheel 1122 400 1218 combined with the original front/wrap handle or rear element 1125 434 5000 may burn out the heaters if run at full throttle for more than about four minutes at a time. Preserve this as a damage warning, not approval for a four-minute mismatched operating procedure.
  • The next service note expressly limits the original front/wrap handle and original rear element 1125 434 5000 to saws with flywheel 1122 400 1216. No adhesive product, bonding cure time or complete replacement procedure is specified here.

Source: TI 2/1996, p. 1 · TI 2/1996, p. 2 · TI 2/1996, p. 3 · TI 2/1996, p. 4 — Page 4 service notes, read with engine-set prerequisites in 1–2 and resistance table in 4.3.

Part numbers (4)
  • 1122 400 1218 — New VH flywheelConditional retrofit · Older 066 only with all engine/ignition/heater prerequisites
  • 1122 400 1216 — Original VH flywheelRequired original-heater pairing · Original front/wrap and rear heaters
  • 1125 434 5000 — Original rear heaterRestricted pairing · Flywheel 1122 400 1216 only
  • 1128 434 5000 — New rear heaterRequired retrofit companion · Bond into rear handle; replace front/wrap heater too

Service note · 064 / 066

064 / 066 heated handles: tube replaces two connector housings

Insulation change at harness/generator plug-and-socket connection; no terminal or wiring redesign inferred.

  • Only machines WITH HANDLE HEATING are described. Tube1121 442 0402, printed3.3x0.9x35, insulates the plug-and-socket connection between wiring harness and generator. It replaces BOTH pin housing1128 431 8400 and socket housing1128 431 8700.
  • Table deletes both housing entries and adds the tube; it does not delete the electrical pins/sockets or authorize cutting/splicing conductors. No tube material, shrink process, dimension interpretation, wiring colours or electrical test values are supplied.
  • Introduction is IN PROGRESS; no exact serial. Original housings remain factory supplied ONLY WHILE EXISTING STOCKS LAST. This differs from the old guard being no longer supplied; do not merge those supply remarks.
  • Historical TI08/1997 evidence for the stated 064/066 configurations only. Independent modification cutoffs are not whole-model identification ranges, current stock claims or blanket retrofit permission. No MS640/MS660 successor scope or tested physical interchange is inferred. No hardware operation was performed.

Source: TI 8/1997, p. 4 — 064 / 066 heated handles: tube replaces two connector housings.

Part numbers (3)
  • 1128 431 8400 — Pin housingOriginal; stocks only · 064 / 066; only the described configuration
  • 1128 431 8700 — Socket housingOriginal; stocks only · 064 / 066; only the described configuration
  • 1121 442 0402 — Insulating tube3.3x0.9x35New replacement for both housings · 064 / 066; only the described configuration

Wrong number or missing part for the 066? Report a correction →