Stihl 1122 · Section A · 1 of 19 · 28 parts
Crankcase
Fits MS 660.
Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.
Parts (28)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1122 020 2116 | Crankcase | 1 |
| 2 | 1122 020 2113 | Crankcase → replaced by 1122 020 2116 TI 10/2007 | 1 |
| 3 | 0000 988 5211 | Connector | 1 |
| 4 | 9371 470 2610 | Cylindrical pin 5x18 | 2 |
| 5 | 0000 974 1200 | Notched pin 2.6x8 | 1 |
| 6 | 1120 162 5200 | Pin | 1 |
| 7 | 1121 162 5205 | Pin | 1 |
| 8 | 1121 162 5200 | Pin | 2 |
| 9 | 1128 640 9100 | Valve | 1 |
| 10 | 9503 003 6676 | Grooved ball bearing 6203 | 1 |
| 11 | 9523 003 4555 | Grooved ball bearing 17x40x14 | 1 |
| 12 | 9022 371 1020 | Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 | 6 |
| 13 | 1128 084 8302 | Reflector foil | 1 |
| 14 | 1138 664 2400 | Collar screw | 2 |
| 15 | 0000 953 6605 | Collar screw M8 | 2 |
| 16 | 9640 003 1850 | Oil seal 17x32.9x3.6 | 1 |
| 17 | 9640 003 1560 | Oil seal 15x22x4 | 1 |
| 18 | 1122 029 0507 | Gasket | 1 |
| 19 | 1122 030 0408 | Crankshaft | 1 |
| 20 | 1120 036 8500 | Woodruff key 2x3.7 | 1 |
| 21 | 1122 647 9400 | Hose | 1 |
| 22 | 1117 640 3800 | Pickup body | 1 |
| 23 | 0000 350 0520 | Filler cap → replaced by 1127 350 0500 TI 48/1995 | 1 |
| 24 | 0000 359 1220 | Sealing ring | 1 |
| 25 | 0000 350 0900 | Rope | 1 |
| 26 | 0000 353 0600 | Hook | 1 |
| 27 | 1125 084 8900 | Grommet | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 1122 007 1053 | Set of gaskets | 1 |
Parts are not interchangeable across engine series — check yours before ordering.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Service note · MS 361 / MS 362 / MS 440 / MS 441 / MS 460 / MS 650 / MS 660 / MS 880
MS 361, MS 362, MS 440, MS 441, MS 460, MS 650, MS 660, MS 880: magnesium stud adhesive changes to Loctite 270
Metric-thread crankcase studs: Loctite 243 (USA 242) → Loctite 270; not polymer housings.
- Exact listed magnesium-crankcase models: MS 361, MS 362, MS 440, MS 441, MS 460, MS 650, MS 660, MS 880. Their metric-thread studs change from Loctite 243 (USA: Loctite 242) to Loctite 270. No stud part number, serial changeover, cure time or torque is specified here.
- Before stud reassembly, clean BOTH threads: insert the tap into the internal thread BY HAND, then blow out the threaded hole; brush off the external stud thread. Coat the cleaned stud with Loctite 270. This thread-cleaning instruction is not permission to enlarge the polymer repair-stud hole.
- Loctite is NOT used for studs in polymer engine housings. The magnesium adhesive change does not override the separate polymer repair restrictions or give these models permission to use the oversized polymer repair studs.
- The repeated words engine housings at the end of page3 are present in the original scan; they add no second instruction and are not silently corrected in the retained source.
- Historical English TI29/2011. Only the printed model and material scope is admitted; no unlisted variants or predecessor models are inferred. No physical interchange test was performed.
Source: TI 29/2011, p. 3 — MS 361, MS 362, MS 440, MS 441, MS 460, MS 650, MS 660, MS 880: magnesium stud adhesive changes to Loctite 270.
No additional parts-table entry added.
Wrong number or missing part for the MS 660? Report a correction →