← 084 · 088 · MS 780/880/881

Stihl 1124 · Section M · 12 of 14 · 21 parts

Handlebar, Shroud

Fits 088.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11010111112131415161718192203456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (21)

PosPart numberDescriptionQty
1 1124 790 1721 Handlebar with hose 1
2 not sold separately Handle hose 450 mm / 17 13/16'' not available as a separate item 1
3 1124 791 5105 Stiffener 1
4 1124 790 3620 Wrap around handlebar with hose 1
5 not sold separately Handle hose 325 mm / 12 13/16'' not available as a separate item 1
6 not sold separately Handle hose 415 mm / 16 3/8'' not available as a separate item 1
7 1124 791 5500 Elbow connector 1
8 9291 021 0140 Washer 6.4 1
9 9022 341 1300 Spline screw IS-M6x20 1
10 9074 478 4475 Pan head self-tapping screw IS-P6x21.5 2
11 9074 478 4675 Pan head self-tapping screw IS-P6x32.5 2
12 1124 080 1610 Shroud → replaced by 1124 080 1602 TI 56/2003 1
13 0000 963 0808 Bushing 2
14 1124 967 1505 Model plate 088 → replaced by 1124 967 1501 TI 56/2003 1
15 1121 084 7000 Slotted nut 1
16 1121 084 6901 Insulator 1
17 1124 084 3000 Shim 1
18 0000 967 1593 Model plate Magnum 1
19 9022 371 1020 Spline screw IS-M5x20 → replaced by 9022 371 1050 TI 30/2004 2
20 1118 145 9000 NLA Plug option 1
Not numbered on the diagram — assemblies, kits and options
— 0000 791 2005 Handle hose Ø 23 mm x 5m / 1x197'' option 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Historical fitment · 088

088: decompression valve and protective cover

Cover 1122 084 1405 sits between cylinder and shroud.

  • The complete valve screws into the cylinder. Its axial plunger has a conical lower end, retained in upper or lower position by three spring-loaded balls offset 120 degrees. Diagram labels are body (1), plunger (2), balls (3), not separate orderable part numbers.
  • Pushing the plunger down opens the bore before starting. During cranking, part of the cylinder pressure escapes through that bore; remaining compression stays below closing pressure. After ignition, pressure lifts the plunger and the cone closes the bore. No numeric opening or closing pressure is given.
  • The shroud opening has a raised surround to protect against accidental valve contact. Cover 1122 084 1405 is installed between cylinder and shroud to help exclude dust and dirt. This cover is not the complete shroud or valve.
  • The stated benefit is reduced starter-rope effort. Construction description is not authorization to operate hardware or evidence of a valve rebuild procedure.

Source: TI 35/1996, p. 1 · TI 35/1996, p. 4 — Cover and section1.6 complete construction/function, drawings137TI006/007 and171TI003.

Part numbers (1)
  • 1122 084 1405 — Decompression-area coverRequired cover · 088; between cylinder and shroud

Wrong number or missing part for the 088? Report a correction →