← 084 · 088 · MS 780/880/881

Stihl 1124 · Section L · 11 of 14 · 41 parts

Carburetor HT-12E

Fits 088.

Parts diagrams →

Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101112131415161718192202122222323242525262728330313233343536373839456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (41)

PosPart numberDescriptionQty
1 1110 122 9410 Plug 1
2 1124 121 5604 Fixed jet 1.04 1
3 1124 121 5405 Valve jet 1
4 1124 121 5000 Inlet control lever 1
5 1110 122 7800 Oval head screw 1
6 1110 121 9200 Spindle 1
7 1124 122 3001 Spring Fitment / change note → 1
8 1124 122 3000 Spring Fitment / change note → → replaced by 1124 122 3001 TI 34/1997 1
9 1110 121 5100 Inlet needle 1
10 1110 121 4700 Metering diaphragm 1
11 1110 129 0900 Gasket 1
12 1124 121 0803 End cover 1
13 1124 122 7102 Screw 4
14 4221 121 7800 Strainer 4
15 1124 121 4800 Pump diaphragm 1
16 1110 129 1110 Gasket 1
17 1124 121 0802 End cover Fitment / change note → 1
18 1110 122 7700 Oval head screw 4
19 1124 122 3200 Torsion spring 1
20 1124 120 7200 Choke shaft with lever 1
21 1124 121 2900 Choke shutter 1
22 1110 122 7400 Round head screw 2
23 1110 122 9005 E-clip 2
24 1124 121 8600 Washer 1
25 4221 122 9100 Bushing 2
26 1124 122 3202 Torsion spring 1
27 1124 120 7100 Throttle shaft with lever 1
28 1124 121 3301 Throttle shutter Fitment / change note → 1
30 1124 122 6200 Idle speed adjustment screw 1
31 1124 122 6803 Low speed adjustment screw 1
32 1124 122 6703 High speed adjustment screw 1
33 1110 122 3030 Spring 2
34 1124 121 2700 Cap 2
35 1124 123 7501 Grommet → replaced by 1124 123 7502 TI 9/2009 1
36 1124 121 5603 Fixed jet 1.00 option 1
37 1124 122 5400 Sleeve 2
38 1124 122 6802 Low speed adjustment screw 1
39 1124 122 6702 High speed adjustment screw 1
Not numbered on the diagram — assemblies, kits and options
— 1124 120 0609 Carburetor HT-12E 1
— 1124 007 1060 Set of carburetor parts Fitment / change note → 1
— not sold separately Carburetor HT-11D no longer available from factory 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 088

088: 084 comparison specifications

Keep maximum-power speed, permissible speed and mean idle speed distinct.

  • The comparison is printed in 084 / 088 order: engine speed at maximum power 9,300 / 8,500 rpm; maximum torque 7.5 Nm (5.5 lb.ft) / 8.0 Nm (5.9 lb.ft), both at 6,000 rpm.
  • Weight 9.4 kg (20.7 lb) / 9.9 kg (21.8 lb); power-to-weight ratio 1.5 / 1.6 kg/kW. This table does not specify a dry-weight or cutting-attachment convention; do not invent one or derive an exact power rating from rounded ratios.
  • Fuel capacity 1250 cm³ (2.64 US pt) / 1300 cm³ (2.75 US pt); oil capacity 630 cm³ (1.33 US pt) / 700 cm³ (1.48 US pt).
  • Maximum permissible speed with Rollomatic bar and chain is 12,500 / 12,000 rpm; mean idle speed is 2,000 / 2,500 rpm. Neither is the speed at maximum power, nor a general unloaded adjustment target.
  • The air-filter comparison is 084 oil-impregnated cotton HD versus 088 wire mesh (winter option) and dry element. It does not apply the 088 no-oil rule to the original 084 filter.
  • Sound pressure Lpeq to ISO 7182 is 102 / 101 dB(A); sound power Lweq to ISO 9207 is 111 / 112 dB(A). Superscript 1 is printed after both standards but no explanatory footnote appears on the retained page; test-condition detail is not invented.
  • These are dated comparison values, not new measurements, complete engine specifications or automatic applicability to later 084/088 revisions and MS successors.

Source: TI 35/1996, p. 6 — Section2 entire084/088 comparison table.

No additional parts-table entry added.

Historical fitment · 088

088: gasket and carburetor service aids

Launch servicing-aid numbers do not establish kit contents.

  • Gasket set 088 1124 007 1051, carburetor parts kit 1124 007 1060 and gasket panel 088 0457 281 2204 are listed as new servicing aids. Contents are not enumerated; no kit-to-every-later-carburetor assertion is inferred from the linked IPL assembly.
  • Other tools/aids and general tightening torques are referred to the separate 088 service manual. No unstated torque is filled in from 084 or a successor model.
  • The bulletin says all repair times are the same as 084, but gives no operation-by-operation times. It also announces a separate 088 illustrated parts list; neither statement proves another document was reviewed here.
  • If started during repairs or maintenance, the source requires compliance with local regulations and owner-manual safety precautions. This offline reference work does not start a machine.

Source: TI 35/1996, p. 7 · TI 35/1996, p. 8 — Sections4.2,5 repair preface,5.3–5.4 and6.

Part numbers (3)
  • 1124 007 1051 — 088 gasket setServicing aid · 088; contents unspecified
  • 1124 007 1060 — Carburetor parts kitServicing aid · 088; launch carburetor; contents unspecified
  • 0457 281 2204 — 088 gasket panelServicing aid · 088; not a torque table

Historical fitment · 088

088: leakage-test preparation and pressures

Replace the decompression valve with the specified plug before the test.

  • Flange 1124 850 4205 seals the muffler opening for leakage testing. Plug 1122 025 2200 must be installed instead of the decompression valve before the leakage test; the source refers to the service manual for the full procedure.
  • The decompression valve is removed/installed with a standard deep-well 13-mm socket. The adjacent tightening torque is 14 Nm (10.3 lbf.ft); do not apply it as a general cylinder, flange or carburetor torque.
  • Printed engine pressure test: 0.6 bar (8.7 psi); engine vacuum test: 0.6 bar (8.7 psi). The vacuum value is a magnitude in the vacuum-test row, not positive pressure or an absolute-pressure statement. Carburetor pressure test: 0.4 bar (5.8 psi).
  • No dwell time, permissible leak-down, complete port-sealing sequence or carburetor setup is printed. These values alone are not a complete executable test or a verified test result.

Source: TI 35/1996, p. 7 · TI 35/1996, p. 8 — Section4.1 flange and section 5.2.1 entire test data.

Part numbers (2)
  • 1124 850 4205 — Muffler-opening sealing flangeLeakage-test tool · 088; muffler opening
  • 1122 025 2200 — Decompression-port plugLeakage-test prerequisite · 088; replaces decompression valve

Service note · 088

088 carburetor: new throttle shutter and end cover

Carburetor 1124 120 0608 keeps its number, but only the new version is supplied.

  • Section 2 is 088 ONLY. Within carburetor 1124 120 0608, throttle shutter 1124 121 3301 replaces 1124 121 3300. End cover 1124 121 0802 replaces 1124 121 0810. Preserve the distinct 3301/3300 and 0802/0810 sequences; these are different components, not equivalent numbering styles.
  • Table item 1 retains carburetor number 1124 120 0608 in BOTH columns and explicitly includes ITEM 2, the throttle shutter. It does NOT explicitly list item 3, the end cover, in that inclusion statement; do not silently extend the printed included-items range. Remark 1 says ONLY the NEW VERSION of the carburetor is available from the factory. Its number alone cannot distinguish the old/new shutter configuration.
  • Remark 2 says original throttle shutter and original end cover are no longer available from the factory. Introduction is IN PROGRESS, no cutoff given. No required shutter/cover pairing, altered settings, geometry or measured performance is specified. The later IPL label HT-12E is a discovery link, not proof that TI17 identifies this carburetor suffix.
  • Historical TI17/1997 evidence for the named model and section only. No serial cutoff is supplied. Factory availability describes the bulletin date, not present stock. No MS880/MS881 scope, reciprocal component interchange or physical verification inferred. No hardware operation was performed.

Source: TI 17/1997, p. 2 — 088 carburetor: new throttle shutter and end cover.

Part numbers (5)
  • 1124 120 0608 — Carburetor, explicitly includes item 2Unchanged number; only new version supplied · 088; 088 carburetor: new throttle shutter and end cover
  • 1124 121 3300 — Original throttle shutterNo longer available from factory · 088; 088 carburetor: new throttle shutter and end cover
  • 1124 121 3301 — New throttle shutterReplacement · 088; 088 carburetor: new throttle shutter and end cover
  • 1124 121 0810 — Original end coverNo longer available from factory · 088; 088 carburetor: new throttle shutter and end cover
  • 1124 121 0802 — New end coverReplacement · 088; 088 carburetor: new throttle shutter and end cover

Service note · 088

088: same-number HT-11B to HT-11C carburetor revision

Second throttle-shutter notch, higher-preload spring and 0.45 mm part-load fixed jet.

  • Carburetor1124 120 0608 changes designation from HT-11B to HT-11C to improve transition from full throttle to idle, for example after chain-brake activation at full throttle. This is the source explanation, not an instruction to test the brake at full throttle.
  • Throttle shutter1124 121 3301 gains a SECOND NOTCH but keeps its number. Spring1124 122 3000 is replaced by1124 122 3001 with HIGHER PRELOAD. Part-load fixed jet diameter increases to0.45 mm (0.018 in.); no previous diameter stated. The unnumbered jet is NOT AVAILABLE AS A SEPARATE ITEM (remark3); no drill-out or jet-only conversion procedure supplied.
  • Both complete carburetors include table items1–3. Only modified carburetor and throttle shutter available from factory (remark1); original spring remains a spare (remark2). Introduction IN PROGRESS; no serial cutoff. Different availability for the spring must not be flattened into whole-assembly stock exhaustion.
  • The exact088 IPL sheet is later titled HT-12E, listing0609 and a reference to HT-11D, while retaining both spring numbers and shutter3301. This note binds the exact088 subsystem and those parts, NOT equivalence of HT-11C, HT-11D and HT-12E or0608/0609. No extension to084, MS880 or other shared-number models. Footer TI17.97 is bibliography; all prose, table rows, remarks and footer reviewed.
  • Historical source guidance and factory supply, not current availability or verified physical interchange. No hardware operation was performed.

Source: TI 34/1997, p. 1 — Complete carburetor revision, all three component rows, supply/introduction and footer.

Part numbers (4)
  • 1124 120 0608 — Carburetor HT-11B / HT-11CSame number; modified-only factory supply · Only the exact model/configuration and restrictions of 1997-34
  • 1124 121 3301 — Throttle shutterSame number; second notch; modified-only supply · Only the exact model/configuration and restrictions of 1997-34
  • 1124 122 3000 — Original springRemains spare · Only the exact model/configuration and restrictions of 1997-34
  • 1124 122 3001 — Higher-preload springNew version · Only the exact model/configuration and restrictions of 1997-34

Wrong number or missing part for the 088? Report a correction →