← 034 · 036 · MS 340/360

Stihl 1125 · Section Q · 16 of 19 · 21 parts

Chain sprocket cover, Handlebar

Fits 034.

Parts diagrams →

Historical fitment & changes (1) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141516161718192203456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (21)

PosPart numberDescriptionQty
1 0000 953 6605 Collar screw M8 2
2 1125 640 1701 Chain sprocket cover Fitment / change note → → replaced by 1122 640 1702, 1128 640 1706 TI 36/2000 1
3 1121 648 6610 Bumper strip 2
4 1125 656 1501 Guard 1
5 0000 955 0801 Hexagon nut M8 2
6 1125 080 1620 Shroud → replaced by 1125 080 1622 TI 44/2002 1
7 1128 792 0900 Reflector foil 1
8 1125 080 8000 Shutter 1
9 9646 945 0590 O-ring 8x2 1
10 9099 021 3760 Self-tapping screw 4.8x13 1
11 1121 084 7000 Slotted nut 1
12 1121 084 6901 Insulator 1
13 1122 084 7100 Cap 1
14 1121 084 7100 Cap 1
15 1125 790 1750 Handlebar 1
16 9074 478 4475 Pan head self-tapping screw IS-P6x21.5 2
17 9074 478 4675 Pan head self-tapping screw IS-P6x32.5 2
18 1125 790 1751 Handlebar 1
19 not sold separately Handle hose 430 mm / 16 15/16'' not available as a separate item 1
20 9074 478 4435 Pan head self-tapping screw IS-P6x19 2
Not numbered on the diagram — assemblies, kits and options
— 0000 791 2009 Handle hose Ø 19 mm x 5 m / 3/4x197'' option 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · 024 / 026 / 034 / 036

024 / 026 / 034 / 036: sprung side plate requires the revised cover

Side plate 1122 664 1000 changes to 1122 664 1001; new plate installation requires the matching new cover. The general cover row changes 1125 640 1700 to 1125 640 1701.

  • When fitting the revised sprung-tab side plate during a repair, the new-version chain sprocket cover must also be fitted. The tabs hold the guide bar during chain assembly; this is not approval to use the new plate with the original cover.
  • Original side plates remain available for original covers/older machines in this bulletin. Original covers are supplied only while existing stocks last; these are historical availability statements.
  • The source identifies new covers by integrally cast numbers 1122 648 0401 and 1125 648 0404. These are identification marks, not the 640-group cover ordering numbers or established ordering aliases. The prose does not explicitly pair each cast number to a summary row.
  • The illustrated installation removes the M4x8 pan-head screw and old plate, pushes the new plate over the bar studs, then seats it using a combination wrench and one short blow with a plastic mallet.
  • For the FIRST installation of a new side plate, the source says to mount the guide bar and cover and tighten the M8 nuts to about 15–20 Nm (11–15 lbf.ft). This historical seating step is not a universal torque specification for later models or normal recurring bar adjustment.
  • Illustrated removal fits an M8 nut to the rear bar stud, twists the combination-wrench screwdriver end about 45° counterclockwise under the plate, raises the wrench end about 10–15 mm (1/2 in), then removes the nut and plate. Preserve the illustrated orientation; no hardware operation is verified here.
  • Pan-head screw 9041 216 0630 is omitted in the revised arrangement, not globally discontinued: the summary says it remains a spare for other models.
  • Introduction is in progress, dated May 17, 1994, without a numeric serial cutoff. The seven explicitly named models do not establish applicability to successors, 046, or unlisted variants. Prior-TI references are bibliography, not inherited compatibility.

Source: TI 12/1994, p. 1 · TI 12/1994, p. 2 · TI 12/1994, p. 3 · TI 12/1994, p. 4 — Cover/side-plate service note, assembly/disassembly and model-qualified summary.

Part numbers (7)
  • 1122 664 1000 — Original side platePrevious version · Retained for original cover
  • 1122 664 1001 — Sprung-tab side plateNew version · Requires new-version cover
  • 1125 640 1700 — Chain sprocket coverPrevious general cover · Historical while-stocks-last availability
  • 1125 640 1701 — Chain sprocket coverNew general cover · Named models in general summary row
  • 9041 216 0630 — Pan-head screw M4x8Removed from new arrangement · Still a spare for other models
  • 1122 648 0401 — Integrally cast cover numberIdentification only · Not an ordering alias or explicit row mapping
  • 1125 648 0404 — Integrally cast cover numberIdentification only · Not an ordering alias or explicit row mapping

Wrong number or missing part for the 034? Report a correction →