← 034 · 036 · MS 340/360

Stihl 1125 · Section H · 8 of 17 · 28 parts

Tank housing

Fits 036.

Parts diagrams →

Historical fitment & changes (6) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110111213141415151617181922021222425262728293456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (28)

PosPart numberDescriptionQty
1 1125 350 0818 Tank housing 1
2 4116 122 6600 Collar screw Fitment / change note → 2
3 1125 122 6600 Collar screw Fitment / change note → 2
4 0000 967 3662 Warning pictogram MS 1
5 0000 350 0525 Filler cap 1
6 9645 948 7734 O-ring 25x3.5 1
7 0000 350 0520 Filler cap → replaced by 1127 350 0500 TI 48/1995 1
8 0000 359 1220 Sealing ring 1
9 0000 350 0900 Rope 1
10 0000 353 0600 Hook 1
11 0000 350 5800 Tank vent → replaced by 0000 350 5804 TI 41/2003 1
12 not sold separately O-ring not available as a separate item 1
13 1121 350 5802 Tank vent → replaced by 0000 350 5800, 0000 350 5800 TI 31/2001 1
14 1120 358 8105 Vent insert Fitment / change note → 1
15 9099 021 2770 Self-tapping screw 3.9x13 Fitment / change note → 1
16 1110 353 1600 Valve Fitment / change note → 1
17 1122 358 1800 Filter 1
18 1121 358 1800 Filter Fitment / change note → → replaced by 1122 358 1800 TI 31/2000 1
19 1121 358 2500 Cap Fitment / change note → 1
20 1125 358 1000 Clip 1
21 1121 350 5800 Tank vent Fitment / change note → 1
22 4114 353 1600 Valve Fitment / change note → → replaced by 1128 353 1600 TI 25/1996 1
24 1119 358 7701 Hose 1
25 0000 350 3504 Pickup body 1
26 1121 791 0600 Handle molding 1
27 9074 478 3076 Pan head self-tapping screw IS-P4x19 1
28 0000 967 3500 NLA Instruction label (4) 1
29 0000 967 3685 Instruction label (6) 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 034 / 036

034 / 036 new tank vent requires modified housing

Same-number tank housing; two printed changeover assignments conflict.

X 32 185 626 / X 31 813 248 (conflicting assignments) — Tank-vent and filler-cap prose contradict the section-number assignments in the page 2 summary; unresolved, not a definitive cutoff.

  • New valve 4114 353 1600, sintered filter 1121 358 1800 and cap 1121 358 2500 replace the production tank vent 1121 350 5800 with vent insert 1120 358 8105 and B3.9 x 13 screw 9099 021 2770. Those three ORIGINAL parts REMAIN AVAILABLE FOR OLDER MACHINES; deletion from production is not deletion from service supply.
  • New vent parts fit ONLY THE MODIFIED TANK HOUSING. Tank housing 1125 350 0803 retains the SAME NUMBER; only the modified version is factory available, supplied together with new vent items 1–3 to ensure interchangeability. A number match alone does not distinguish old and modified housings; no permission to put the new vent into an old housing is given.
  • Housing redesign also replaces switch shaft 1121 182 0900 with 1125 182 0900. Original shaft remains available for STIHL 024; this is a supply exception, not an extension of the new 034/036 housing to 024. All other parts as before.
  • UNRESOLVED PRINTED CONFLICT: section 1.1 prose on page 1 assigns the tank vent to X 32 185 626; section 1.2 prose on page 2 assigns the filler-cap retainer to X 31 813 248. The page 2 summary instead assigns 1.1 to X 31 813 248 and 1.2 to X 32 185 626. Both original scans confirm the reversal. Neither is selected as the authoritative changeover; serial alone cannot settle this TI applicability.
  • Later 034 J and 036 H sheets list tank housing 1125 350 0818 and multiple vent designs; later 034 L and 036 K list switch shaft 1125 182 0901. These do not establish a 0803-to 0818 or 0900-to 0901 supersession chain, nor resolve the conflicting TI serials.
  • Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 28/1995, p. 1 · TI 28/1995, p. 2 — Sections 1/1.1 and page 2 summary/remarks.

Part numbers (9)
  • 1121 350 5800 — Original tank ventretained for older machines · 034 / 036; Sections 1/1.1 and page 2 summary/remarks
  • 1120 358 8105 — Vent insertretained for older machines · 034 / 036; Sections 1/1.1 and page 2 summary/remarks
  • 9099 021 2770 — Self-tapping screw B3.9 x 13retained for older machines · 034 / 036; Sections 1/1.1 and page 2 summary/remarks
  • 1125 350 0803 — Tank housingsame-number revision; supplied with items 1–3 · 034 / 036; Sections 1/1.1 and page 2 summary/remarks
  • 4114 353 1600 — Valvenew item 1 · 034 / 036; Sections 1/1.1 and page 2 summary/remarks
  • 1121 358 1800 — Sintered filternew item 2 · 034 / 036; Sections 1/1.1 and page 2 summary/remarks
  • 1121 358 2500 — Vent capnew item 3 · 034 / 036; Sections 1/1.1 and page 2 summary/remarks
  • 1121 182 0900 — Original switch shaftretained for 024 · 034 / 036; Sections 1/1.1 and page 2 summary/remarks
  • 1125 182 0900 — Switch shaftreplacement · 034 / 036; Sections 1/1.1 and page 2 summary/remarks

Service note · 034 / 036

034 / 036 modified tank vent: inlet and outlet pressures

Air inlet at 5–50 mbar vacuum; outlet at 200–300 mbar above atmosphere.

X 32 185 626 / X 31 813 248 (conflicting assignments) — Tank-vent and filler-cap prose contradict the section-number assignments in the page 2 summary; unresolved, not a definitive cutoff.

  • For the MODIFIED valve/filter/cap system, air enters at approximately 5–50 mbar VACUUM (printed negative 0.07–0.72 psi) and leaves at about 200–300 mbar ABOVE ATMOSPHERIC PRESSURE (2.9–4.35 psi). These are different directional operating ranges, not one bidirectional relief threshold. Nominal printed conversions retained.
  • Pressure equalizes through cap(3), controlled by sintered filter(2) and valve(1). The cap protects the filter against icing and locates inlet/outlet in a low-dust zone of the carburetor box; the filter helps prevent dirt entering the valve. The arrow is an airflow location, not a drilling or fitting direction.
  • These approximate operating values are not a complete leak-test procedure, calibrated acceptance tolerance or authority to pressurize a connected saw. No test duration or pump method is supplied. New vent parts require the modified housing; old vent behavior is not specified here.
  • UNRESOLVED PRINTED CONFLICT: section 1.1 prose on page 1 assigns the tank vent to X 32 185 626; section 1.2 prose on page 2 assigns the filler-cap retainer to X 31 813 248. The page 2 summary instead assigns 1.1 to X 31 813 248 and 1.2 to X 32 185 626. Both original scans confirm the reversal. Neither is selected as the authoritative changeover; serial alone cannot settle this TI applicability.
  • Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 28/1995, p. 1 · TI 28/1995, p. 2 — Section 1.1 operation and figures 138TI 002 KN/133TI 002.

Part numbers (3)
  • 4114 353 1600 — Valvepressure-control item 1 · 034 / 036; Section 1.1 operation and figures 138TI 002 KN/133TI 002
  • 1121 358 1800 — Sintered filteritem 2 · 034 / 036; Section 1.1 operation and figures 138TI 002 KN/133TI 002
  • 1121 358 2500 — Vent capitem 3 · 034 / 036; Section 1.1 operation and figures 138TI 002 KN/133TI 002

Service note · 034 / 036

034 / 036 filler-cap cord: direct tank lug attachment

Replacement caps still include the hook; serial assignments conflict.

X 32 185 626 / X 31 813 248 (conflicting assignments) — Tank-vent and filler-cap prose contradict the section-number assignments in the page 2 summary; unresolved, not a definitive cutoff.

  • Cord(A) attaches directly to an eye in the tank housing; suitable lugs are provided on BOTH chain-oil and fuel tanks. Hook(B) is discontinued on the production line but REMAINS AVAILABLE AS A SPARE PART. The filler-cap part number remains unchanged, but this TI prints no filler-cap or hook ordering number.
  • Replacement filler caps are supplied WITH HOOK. The hook MAY BE REMOVED before fitting a cap to a TANK WITH LUGS. This is conditional on physical lug provision, not an instruction to discard hooks on older tanks or create a new eye.
  • UNRESOLVED PRINTED CONFLICT: section 1.1 prose on page 1 assigns the tank vent to X 32 185 626; section 1.2 prose on page 2 assigns the filler-cap retainer to X 31 813 248. The page 2 summary instead assigns 1.1 to X 31 813 248 and 1.2 to X 32 185 626. Both original scans confirm the reversal. Neither is selected as the authoritative changeover; serial alone cannot settle this TI applicability.
  • Later 034 J/036 H sheets list filler caps 0525/0520, rope 0900 and hook 0600. Their presence does not identify which cap version the unnumbered TI means or prove a serial assignment. No unprinted ordering number has been assigned to this note.
  • Historical TI guidance for the named models and stated versions only. Shared IPL sheets or series do not extend applicability to other variants or successor models. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 28/1995, p. 2 — Section 1.2 filler cap, figure and summary cutoff.

No additional parts-table entry added.

Service note · 036

036 compensator retrofit: complete assembly and lower tank vent required

Retrofit threshold X 32 185 626 is not factory introduction X 32 622 640.

  • 036 retrofit restriction: ONLY from X 32 185 626, with the LOWER tank vent providing clearance, and ONLY AS A COMPLETE ASSEMBLY of air filter, metering end cover with compensator connector and carburetor box cover. Factory introduction X 32 622 640 is a DIFFERENT threshold. TI28/1995 reverses its tank-vent and cap-retainer serials between prose and summary; TI30 agrees with its vent prose but is not an explicit correction. Preserve that conflict; verify the actual housing/vent configuration, not serial alone.
  • New filter has a much larger area, felt fabric, inner-half opening for the compensator connector and retaining lugs for the carburetor box cover. Sleeve 1125 121 9100 connects the clean-air side to the connector on the modified metering end cover, exposing the OUTSIDE of the metering diaphragm to clean-air pressure.
  • The TI describes this compensator as preventing mixture enrichment as the filter gets dirty, so the high-speed screw need not be readjusted merely for increasing filter contamination. This is a historical functional claim, not a guarantee for damaged filters or a deletion of maintenance. No numeric filtration efficiency, service interval or carburetor setting is supplied.
  • Page 6 explicitly separates ORIGINAL upper diagram from NEW lower diagram. Their item numbers resolve against page 7, not later IPL positions. The complete-system restriction is not permission to mix individual new and old filter/cover components.
  • Historical TI guidance for the named models and stated versions only. Shared series and later IPL sheets do not extend applicability to other variants or successors. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 30/1995, p. 1 · TI 30/1995, p. 4 · TI 30/1995, p. 5 · TI 30/1995, p. 6 · TI 30/1995, p. 7 — Section 1.2 features, 1.2.2 restrictions and assembly figures.

Part numbers (3)
  • 1125 121 9100 — Compensator sleeveclean-air connection · 036; Section 1.2 features, 1.2.2 restrictions and assembly figures
  • 1125 121 0804 — Metering end cover with connectorcomplete-system component · 036; Section 1.2 features, 1.2.2 restrictions and assembly figures
  • 1125 140 1903 — Carburetor box covercomplete-system component · 036; Section 1.2 features, 1.2.2 restrictions and assembly figures

Service note · 036

036 tank housing: longer collar screw for modified air filter

0803 becomes 0813 with screw 4116 122 6600 from X 32 622 640.

  • Tank housing 1125 350 0803 is replaced by 1125 350 0813, INCLUDING longer collar screw 4116 122 6600 in place of 1125 122 6600. This change is connected to the modified air filter in section1.2. Introduction FROM X 32 622 640.
  • Original housing supplied only while factory stocks last; original collar screw REMAINS A SPARE FOR OLDER MACHINES. Longer is qualitative here: no length, mounting torque or independent permission to put the longer screw in any old housing is printed.
  • This housing revision is separate from TI28 same-number 0803 vent revision and TI30 retrofit eligibility X 32 185 626. Later 036 H lists housing 1125 350 0818 and both collar screws; that does not establish an 0813-to 0818 supersession.
  • Historical TI guidance for the named models and stated versions only. Shared series and later IPL sheets do not extend applicability to other variants or successors. Supply statements are historical, not present stock guarantees or verified physical interchange. No hardware operation was performed.

Source: TI 30/1995, p. 8 — Section 2 complete housing summary and supply remarks.

Part numbers (4)
  • 1125 350 0803 — Original tank housingstocks-only original · 036; Section 2 complete housing summary and supply remarks
  • 1125 350 0813 — New tank housingincludes longer collar screw · 036; Section 2 complete housing summary and supply remarks
  • 1125 122 6600 — Original collar screwolder-machine spare · 036; Section 2 complete housing summary and supply remarks
  • 4116 122 6600 — Longer collar screwincluded in new housing · 036; Section 2 complete housing summary and supply remarks

Conditional replacement · 034 / 036 / 036 QS

034 / 036: revised tank vent and S-shaped fuel hose

Same-number tank housings; standard 036 cutoff, deferred heated/QS rollout and temporary hose inclusion remain distinct.

X 39 108 850 — Page 2 specifies standard 036; page 1 says all versions, while heated/QS production is deferred. Conflict retained; no universal serial selector or restriction on stated replacement use.

  • Page 1 says the modified tank housing enters ALL VERSIONS from X 39 108 850, but the page 2 summary explicitly says STANDARD 036 and its Note defers HEATED HANDLE AND QS versions to a LATER DATE. This is a retained internal scope conflict, not a universal 034/036/QS serial range. No separate 034 production date or delayed-variant serial is supplied. The new tank housing MAY BE USED FOR REPLACEMENT PURPOSES on those deferred versions; production timing is not a repair prohibition.
  • Tank housing 1125 350 0813 and handle-heating housing 1125 350 0812 each keep the SAME ORDER NUMBER in original/new columns. Both include summary items 2–5. Remark 1 says ONLY MODIFIED VERSIONS are available from the factory; the order number alone cannot distinguish old and modified housings.
  • The original valve 4114 353 1600 permits air both INTO AND OUT OF the fuel tank. New mushroom valve 1110 353 1600 permits air IN ONLY. Drawings 145TI016 KN (original left, new right) and 145TI017 KN show the changed valve and inward airflow as fuel consumption lowers tank pressure and opens the mushroom valve to equalize with atmosphere. The printed phrase “two-valve valve” is retained as source wording, not a claim of two separate replaceable valves.
  • IMPORTANT source instruction: heat or sunlight can still produce POSITIVE PRESSURE in the fuel tank. ALWAYS OPEN THE FILLER CAP SLOWLY to release excess pressure gradually and avoid fuel spills. The new inlet-only valve is not a pressure-relief outlet. No drilling dimensions, vent test pressure or valve-only retrofit into an original housing is established.
  • S-shaped intake hose 1127 358 7705 replaces straight hose 1119 358 7700 and REQUIRES A LARGER OPENING in the tank housing. Replacement housings also have that opening. Page 2 says supplied with the new hose for ABOUT THE NEXT 2 YEARS; summary remark 2 specifies inclusion with item 1 UP TO THE END OF 1999. These are historical supply limits, not a present-day kit-content promise or permission to enlarge an old tank by an invented procedure.
  • Summary item 3 filter 1121 358 1800 and item 4 cap 1121 358 2500 are UNCHANGED inclusions; the cap is the listed vent component, not an invented replacement fuel filler cap. Item 5 valve changes to 1110 353 1600. Original valve 4114 353 1600 REMAINS AVAILABLE FOR OTHER MODELS (remark 3) AND OLDER MACHINES (remark 4); original straight hose 1119 358 7700 REMAINS AVAILABLE FOR OLDER MACHINES (remark 4). Dashes in the hose columns do not override these explicit supply remarks.
  • Exact 034/036 tank IPLs retain valve 1110 353 1600, filter 1121 358 1800 and cap 1121 358 2500; the QS tank sheet also retains housing 1125 350 0812. Later catalog tank 0818/0819 and hose 7701/7703 entries differ from this TI and do not establish a supersession chain for 0813 or 7705. The 036 IPL also retains original valve 4114 353 1600. All catalog rows and the conflicting rollout statements remain unchanged.
  • Historical TI 11/1998, models 034/036, series 1125; QS is included only where the tank section expressly names it. Shared parts do not extend these changes to MS 360 or other models. Factory supply statements are historical, not current availability. Source-stated replacement permission is not physical-fit verification. No hardware operation was performed.

Source: TI 11/1998, p. 1 · TI 11/1998, p. 2 — Section 1 complete pages 1–2: drawings 145TI016/017 KN, function and Important warning; hose/variant Note; seven summary rows and all four remarks.

Part numbers (8)
  • 1125 350 0813 — Tank housing; same order numberModified version only; includes items 2–5 · 034/036; exact variants and conditions in this note
  • 1125 350 0812 — Handle-heating tank housing; same order numberModified version only; deferred production, replacement permitted · 034/036; exact variants and conditions in this note
  • 1127 358 7705 — S-shaped fuel intake hoseLarger tank opening required; housing inclusion through end 1999 · 034/036; exact variants and conditions in this note
  • 1119 358 7700 — Original straight intake hoseRemains available for older machines · 034/036; exact variants and conditions in this note
  • 1121 358 1800 — FilterUnchanged housing inclusion item 3 · 034/036; exact variants and conditions in this note
  • 1121 358 2500 — CapUnchanged housing inclusion item 4 · 034/036; exact variants and conditions in this note
  • 4114 353 1600 — Original bidirectional valveRemains available for other models and older machines · 034/036; exact variants and conditions in this note
  • 1110 353 1600 — Inlet-only mushroom valveModified housing valve item 5 · 034/036; exact variants and conditions in this note

Wrong number or missing part for the 036? Report a correction →