← 034 · 036 · MS 340/360

Stihl 1125 · Section F · 2 of 8 · 26 parts

Clutch, Chain brake

Fits 036 QS.

Parts diagrams →

Historical fitment & changes (24) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
11011121314151617181922021222324253456789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (26)

PosPart numberDescriptionQty
1 1125 160 2006 Clutch 1
2 1125 162 3202 Carrier 1
3 1128 162 3000 Retainer 3
4 1128 162 0807 Clutch shoe 3
5 0000 997 5815 Tension spring 3
6 1128 162 1001 Cover washer 58 mm / 2 5/16'' 1
7 1128 162 1000 Cover washer 43 mm / 1 3/4'' → replaced by 1128 162 1001, 1128 162 1001 TI 37/2001 1
8 9512 933 2380 Needle cage 10x16x12 → replaced by 9512 933 2382, 1122 967 1503 TI 53/2002 1
9 1125 160 5451 Brake band 1
10 not sold separately Clutch drum not available as a separate item 1
11 0000 642 1223 Rim sprocket 3/8" 7T 1
12 0000 958 1022 Washer Ø 27 mm 1
13 9460 624 0801 E-clip 8x1.3 1
14 1125 162 9300 Screw 1
15 1125 160 5001 Lever 1
16 1125 160 5501 Tension spring 1
17 1125 162 8001 Hose 32 mm / 1 3/16'' 1
18 1125 162 7905 Tension spring 1
19 1121 162 5010 Lever 1
20 0000 997 0628 Spring 1
21 9460 624 0400 E-clip 4 1
22 1125 792 9100 Hand guard 1
23 1125 021 1104 Cover 1
24 9022 313 0660 Spline screw IS-M4x12 3
25 0000 967 3630 Instruction label 1
Not numbered on the diagram — assemblies, kits and options
— 1125 160 2052 Clutch 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Service note · 036 QS

036 QS Quickstop Super: three activation paths and rear-handle reset

Rear-handle release adds a QS braking path; manual and inertia activation remain.

  • TI 45/1995 introduces the 036 QS, series 1125. Its cover photograph and introductory claims describe this variant, not a standard 036 conversion kit. The claimed world-first status and enhanced safety are historical manufacturer statements, not independently reproduced findings.
  • The throttle-trigger interlock lever also activates the QS system. Pressing it while the engine runs releases the brake band from the clutch drum so the chain CAN rotate; releasing BOTH interlock lever and throttle trigger tightens the band and stops the chain within the source’s qualitative “fractions of a second”. No numerical stopping-time limit is stated.
  • Three activation paths remain distinct: front-hand-guard inertia in CERTAIN kickback situations; the user’s hand contacting that guard; and release of the rear-handle interlock lever AND trigger. The two page 2 figures show downward interlock motion to disengage and upward release to engage. They do not promise protection in every kickback.
  • After INERTIA OR MANUAL activation, the rear handle (throttle trigger and interlock lever) must be released to RESET the braking system. No additional control is introduced. The source’s “almost all situations” wording for ergonomic activation is not an unconditional guarantee.
  • Historical TI evidence, not current supply, verified physical interchange or a complete repair procedure. No hardware operation was performed. Exact-model IPL links identify components only; their later edition is not backdated to 1995.

Source: TI 45/1995, p. 1 · TI 45/1995, p. 2 — 036 QS Quickstop Super: three activation paths and rear-handle reset.

No additional parts-table entry added.

Service note · 036 QS

036 QS modular brake and oil pump: changed hardware, separate IPL

6.0 kg versus 5.7 kg for 036; brake-band position controls oil pump.

  • Page 3 says specifications match the 036 except weight rises from 5.7 kg (12.6 lb) to 6.0 kg (13.2 lb). No weighing configuration is given here; do not invent dry/wet or bar-and-chain inclusion. No other standard-036 numerical specification is supplied by this TI.
  • The six listed changes are: oil-pump housing supports braking-system parts in modular construction; bigger chain-sprocket bearing; improved dust seal; ceramic-coated brake band; oil pump controlled by brake-band position; and a crankshaft-mounted cam engaging the chain brake. No bearing dimensions, coating specification or retrofit compatibility are established.
  • Page 6 says a SEPARATE illustrated parts list exists for 036 QS. The retained 2012 catalog has exact 036 QS sheets for oil pump, clutch/chain brake and throttle control; this establishes navigation, not that every 2012 revision was present in 1995. Use original replacement parts per the latest parts list, as page 4 directs. The “Last Technical Information on model 036” field on page 6 is BLANK; no prior issue number is reconstructed.
  • Historical TI evidence, not current supply, verified physical interchange or a complete repair procedure. No hardware operation was performed. Exact-model IPL links identify components only; their later edition is not backdated to 1995.

Source: TI 45/1995, p. 3 · TI 45/1995, p. 4 · TI 45/1995, p. 6 — 036 QS modular brake and oil pump: changed hardware, separate IPL.

No additional parts-table entry added.

Service note · 036 QS

036 QS historical brake check: cutting attachment and manual dependency

Bar and chain must be fitted; qualitative stopping criterion is not a measured test result.

  • Page 3 restricts inspection, servicing and repair to properly trained and authorized personnel. If startup is necessary during maintenance, it requires local/national safety rules AND the owner’s-manual precautions.
  • The stated historical check is WITH BAR AND CHAIN FITTED: open throttle wide, release rear-handle interlock lever and throttle trigger, and require the chain to stop within fractions of a second. The TI gives no numerical timeout, test repetitions or operating-area setup. This records the source, not a complete startup or safe bench-test procedure.
  • A bounded inventory found a service manual whose actual cover is STIHL 034, 036, 036 QS, edition 1999-10 (despite a filename naming MS successors). It is a later SERVICE manual, not the owner’s manual required here. Exact owner-manual safety instructions remain an external source gap; no saw was started or brake performance measured.
  • Historical TI evidence, not current supply, verified physical interchange or a complete repair procedure. No hardware operation was performed. Exact-model IPL links identify components only; their later edition is not backdated to 1995.

Source: TI 45/1995, p. 3 — 036 QS historical brake check: cutting attachment and manual dependency.

No additional parts-table entry added.

Service note · 036 QS

036 QS brake cleaning: grease arrows differ from clutch-drum oil arrow

Mobilplex 0781 120 1111 at filled arrows; chain oil on clutch-drum outside diameter.

  • For improper brake operation, page 4 treats the illustrated sliding/bearing points by contamination level. LIGHT contamination: clean all parts with brush and white spirit. HEAVY contamination or resin clogging: remove affected parts, clean with white spirit or resin solvent, replace worn/damaged parts, and clean machine recesses/seats before reinstallation. No solvent soak duration or substitute chemical is specified.
  • In BOTH cases, the FILLED BLACK arrows in figures 148TI003 KN (rear-handle linkage) and 148TI004 KN (brake mechanism) denote Mobilplex 0781 120 1111 grease. The OUTLINED arrow denotes chain lubricant on the OUTSIDE DIAMETER OF THE CLUTCH DRUM. These distinct symbols do not instruct greasing the entire drum or oiling all pivots. The figures are the exact location reference; no unlabelled point is assigned an invented part number.
  • Pages 2 and 4 require quality chain lubricant and recommend STIHL Bioplus as the ONLY biological chain oil. The wording does not prohibit all non-biological quality oils. It applies also to sliding/pivot lubrication; unsuitable lubricants may cause resin buildup and premature brake failure. Do not replace the explicit Mobilplex grease arrows with a blanket Bioplus instruction.
  • Historical TI evidence, not current supply, verified physical interchange or a complete repair procedure. No hardware operation was performed. Exact-model IPL links identify components only; their later edition is not backdated to 1995.

Source: TI 45/1995, p. 2 · TI 45/1995, p. 4 — 036 QS brake cleaning: grease arrows differ from clutch-drum oil arrow.

Part numbers (1)
  • 0781 120 1111 — Mobilplex grease; filled-arrow locationsspecified · 036 QS brake and rear-handle linkage; not clutch-drum oil coating

Service note · 036 QS

036 QS four torque rows: Loctite 648 and printed Loctite 242 labels

Row-specific Nm/lbf.ft values; same adhesive number has a conflicting name in TI43.

  • Page 5 gives four rows: spline screw IS-DG 4×12, oil pump/crankcase — 3.5 Nm (2.6 lbf.ft), NO adhesive footnote; spline screw IS-DG 5×30, printed “Handschutzhebel/hand guard” — 7.0 Nm (5.2 lbf.ft), remark 1; hex-head screw M6×20, hand guard/crankcase — 6.5 Nm (4.8 lbf.ft), remark 2; pin M7×0.75, pin/oil pump — 7.0 Nm (5.2 lbf.ft), remark 2. Preserve the printed mixed-language joint label without inventing a different attachment.
  • Remark 1 requires adhesive 0786 111 1117, LOCTITE 648, on the IS-DG 5×30 joint. Remark 2 requires 0786 111 1101, printed LOCTITE 242, on BOTH the M6×20 joint and M7×0.75 pin. The pin inherits remark 2 despite the remark’s generic “screw” wording. No adhesive requirement is attached to IS-DG 4×12.
  • CONFLICT RETAINED: TI 45/1995 calls 0786 111 1101 Loctite 242, while TI 43/1995 pages 11–12 call the same number Loctite 243. No equivalence, reformulation or correction has been established; neither source label is silently changed and this is not a substitute-product approval.
  • “All other parts as 036” is a cross-reference, not permission to transfer these four torques to all joints. The available 1999-10 service manual is later than this 1995 TI; no later torque values are imported or backdated here.
  • Historical TI evidence, not current supply, verified physical interchange or a complete repair procedure. No hardware operation was performed. Exact-model IPL links identify components only; their later edition is not backdated to 1995.

Source: TI 45/1995, p. 5 — 036 QS four torque rows: Loctite 648 and printed Loctite 242 labels.

Part numbers (2)
  • 0786 111 1117 — Loctite 648 adhesivespecified · 036 QS IS-DG5×30 hand-guard joint; remark 1
  • 0786 111 1101 — Printed Loctite 242 adhesive; conflicting TI43 label retainedspecified · 036 QS M6×20 hand-guard/crankcase and M7×0.75 pin/oil-pump joints; remark 2

Service note · 036 QS

036 QS DG thread preservation and adhesive heating caution

Find the existing thread counterclockwise before tightening clockwise with a torque wrench.

  • DG screws form a permanent thread in polymer on first insertion. The source’s repeated-removal claim is conditional on observing the SPECIFIED TORQUE with a TORQUE WRENCH, not proof a damaged thread can be reused.
  • For an existing DG thread: place screw in the hole, rotate COUNTERCLOCKWISE until it drops slightly, then tighten CLOCKWISE to the specified torque. This engages the existing thread instead of cutting a new one and weakening the assembly.
  • Adhesive-secured screws are easier to release after heating the adhesive with a hot-air blower (hair dryer). The explicit caution is NOT TO OVERHEAT POLYMER COMPONENTS. No temperature, exposure duration or open-flame method is specified.
  • Historical TI evidence, not current supply, verified physical interchange or a complete repair procedure. No hardware operation was performed. Exact-model IPL links identify components only; their later edition is not backdated to 1995.

Source: TI 45/1995, p. 5 — 036 QS DG thread preservation and adhesive heating caution.

No additional parts-table entry added.

Service note · 036 QS

036 QS historical repair times: two dashes and six loaded-test marks

Twenty task rows in minutes; missing times are not zero; handle tasks are each 40 minutes.

  • Page 6 lists MINUTES for trained personnel in a properly equipped service workshop. Its dotted cut-out is for page 3 of the contemporary repair-times table. These are historical shop allowances, not measured owner durations, pressure-hold times or present billing promises.
  • Rows 1–7: (1) crankcase, engine pan, pressure test* 140; (2) engine housing —; (3) crankshaft, bearings, pressure test* 130; (4) sealing rings, pressure test* 70; (5) crankcase leakage test, test run 25; (6) cylinder, piston, pressure test* 45; (7) ignition system, contact* 25.
  • Rows 8–14: (8) fuel supply, tank vent, test run 15; (9) manifold or flange, pressure test 20; (10) carburetor, check* 25; (11) tank housing with test run 40; (12) oil supply —; (13) oil pump, test run 30; (14) handle frame, front handle, handle housing, shroud, EACH with test run 40. Row 14 is not a combined four-item job.
  • Rows 15–20: (15) rewind starter with test run 20; (16) clutch, test run 20; (17) chain brake, test run, check operation WITH CUTTING ATTACHMENT 35; (18) muffler 10; (19) air filter 5; (20) stop switch 10. Dashes in rows 2 and 12 are UNSPECIFIED, not zero or evidence that repair is impossible.
  • The asterisk means TEST RUN UNDER LOAD, on exactly rows 1, 3, 4, 6, 7 and 10. Other explicit test-run wording remains distinct. No test load or run duration is given. The closing imprint is November 16, 1995; it does not establish a production-serial cutoff.
  • Historical TI evidence, not current supply, verified physical interchange or a complete repair procedure. No hardware operation was performed. Exact-model IPL links identify components only; their later edition is not backdated to 1995.

Source: TI 45/1995, p. 6 — 036 QS historical repair times: two dashes and six loaded-test marks.

No additional parts-table entry added.

Service note · 036 QS

036 QS brake checks: interlock release and hand guard are separate tests

With bar and chain fitted, both checks require standstill within fractions of a second.

  • Section 1 explicitly says WITH BAR AND CHAIN. In 1.1 the historical check opens the throttle wide, then releases the REAR HANDLE to activate the interlock-linked brake. In 1.2 it separately opens the throttle wide and activates the HAND GUARD. Each requires the chain to come to a standstill within fractions of a second; no numerical stopping-time limit is supplied.
  • The printed fault labels are A: brake cannot be activated; B: brake cannot be activated by interlock lever; C: brake cannot be activated by hand guard; D: brake cannot be activated by interlock lever OR hand guard. A and D are retained separately as printed, not silently merged or turned into inferred causes. The extracted body corrupts these letters; the scan is authoritative.
  • These are historical test descriptions for trained, authorized personnel, not authorization to run a saw or an unattended full-throttle test. Fault causes and repairs are in later sections, not established by this page alone.
  • Historical TI evidence for 036 QS (Quickstop Super), series 1125 ONLY; not ordinary 036, 034, MS 360 or MS 360 C compatibility. Inspection, maintenance and repair are restricted by the source to properly trained and authorized personnel. This is a source-linked service reference, not a complete repair or operating procedure; all assembly, maintenance and troubleshooting sections must be read together with the original figures. No hardware operation was performed. Exact-model IPL links identify components, not proof that a 2012 part revision existed in 1996.

Source: TI 1/1996, p. 1 — 036 QS brake checks: interlock release and hand guard are separate tests.

No additional parts-table entry added.

Service note · 036 QS

036 QS chain-brake access: spring tool and band support stay explicit

Disconnect the brake spring with an assembly tube before removing drum and band.

  • Section 2.2 and figures 7–11: remove chain sprocket cover and side plate, E-clip (1), washer (2) and chain sprocket (3). Then remove the separate washer (4) and unscrew cover (5). The two washers are not silently combined.
  • Use assembly tube (9) to disconnect brake spring (8). The source names the tool but gives no tool number or dimensions on this page. Remove clutch drum (6) and needle cage (7); remove clip (10), then brake band (11) TOGETHER WITH support plate (12).
  • Numbers 1–12 in this section are local figure callouts, not the interlock-section callouts or IPL positions. This access sequence is not a complete repair, nor permission to release a loaded spring without the applicable training and complete source procedure.
  • Historical TI evidence for 036 QS (Quickstop Super), series 1125 ONLY; not ordinary 036, 034, MS 360 or MS 360 C compatibility. Inspection, maintenance and repair are restricted by the source to properly trained and authorized personnel. This is a source-linked service reference, not a complete repair or operating procedure; all assembly, maintenance and troubleshooting sections must be read together with the original figures. No hardware operation was performed. Exact-model IPL links identify components, not proof that a 2012 part revision existed in 1996.

Source: TI 1/1996, p. 2 — 036 QS chain-brake access: spring tool and band support stay explicit.

No additional parts-table entry added.

Service note · 036 QS

036 QS brake linkage: preserve washers, cam, rod and spring order

Figures 12–18 continue beyond drum removal; no clutch torque or thread direction is supplied here.

  • Figure 12 says remove clutch (13), with shroud and spark plug in parentheses. It does not specify a piston-locking method, clutch thread direction or torque. Figure 13 then removes cover washer (14) and cover (15); figure 14 removes spacer ring (16), worm gear (17) and cam (18). These are distinct items, not one generic washer.
  • Figure 15 removes hex-head screw (19) from crankcase and washer (20) from hand-guard lever (21), then the screw assembly from the fan housing and the hand guard. Figure 16 removes stop plate (22), E-clip (23), pulls off brake lever (25), and disconnects rod (24).
  • Figure 17 presses compression spring (26) DOWNWARDS while removing locating lever (27) AT THE SAME TIME. Figure 18 removes torsion spring (28). The directional/simultaneous relationship is retained, not rewritten as unrelated removals.
  • The source requires cleaning with STIHL universal cleaner and replacing damaged parts using original replacements according to the latest parts list. No production serial, replacement number or universal QS conversion is claimed.
  • Historical TI evidence for 036 QS (Quickstop Super), series 1125 ONLY; not ordinary 036, 034, MS 360 or MS 360 C compatibility. Inspection, maintenance and repair are restricted by the source to properly trained and authorized personnel. This is a source-linked service reference, not a complete repair or operating procedure; all assembly, maintenance and troubleshooting sections must be read together with the original figures. No hardware operation was performed. Exact-model IPL links identify components, not proof that a 2012 part revision existed in 1996.

Source: TI 1/1996, p. 3 — 036 QS brake linkage: preserve washers, cam, rod and spring order.

No additional parts-table entry added.

Service note · 036 QS

036 QS brake assembly: cam arrow points up and stop plate must seat

Preserve the printed linkage order and distinguish the rod wording from a component identification.

  • Section3.3 figure31 places torsion spring (28) in crankcase. On page6 figure17 hooks locating lever (27) onto the torsion spring, presses compression spring (26) DOWNWARDS and allows locating lever (27) to engage.
  • Figure19 attaches brake cable (31) to the brake lever, fits oil-pump housing (30), and secures it with spline screws (29). Its last instruction literally says PLACE ROD IN THE VALVE. The scan confirms this wording; the intended component is not silently renamed, and no oil-metering adjustment is inferred.
  • Figure32 attaches rod (24) to brake lever (25), fits E-clip (23) and pushes stop plate (22) into position. Figure15 fits hand-guard lever (21), washer (20) and hex-head screw (19) into the crankcase.
  • Figure14 fits worm gear (17), cam (18) with its ARROW POINTING UP, and spacer ring (16) on the crankshaft. Figure13 fits cover (15) and cover washer (14); figure12 installs clutch (13). No clutch torque or thread direction is specified here.
  • Figure11 fits brake band (11) WITH support plate (12) and secures clip (10); figure9 uses assembly tube (9) to attach brake spring (8). The printed sequence attaches the spring before page7 fits the clutch drum. This is retained as source order, not independently validated hardware sequencing.
  • Historical TI evidence for 036 QS (Quickstop Super), series 1125 ONLY; not ordinary 036, 034, MS 360 or MS 360 C compatibility. Inspection, maintenance and repair are restricted by the source to properly trained and authorized personnel. This is a source-linked service reference, not a complete repair or operating procedure; all assembly, maintenance and troubleshooting sections must be read together with the original figures. No hardware operation was performed. Exact-model IPL links identify components, not proof that a 2012 part revision existed in 1996.

Source: TI 1/1996, p. 5 · TI 1/1996, p. 6 — 036 QS brake assembly: cam arrow points up and stop plate must seat.

No additional parts-table entry added.

Service note · 036 QS

036 QS outer brake assembly: retain both washer positions

Needle cage and drum precede cover/washer and sprocket/washer/E-clip.

  • Page7 repeats figure10: fit needle cage (7) and clutch drum (6). Figure8 fits cover (5) and washer (4). Figure7 fits chain sprocket (3) and the SEPARATE washer (2), secured with E-clip (1), then side plate and chain sprocket cover.
  • These assembly-stage callouts are not ordering numbers or a new combination kit. The source does not give a cover torque or declare that assembly alone passes the two operational checks on page1.
  • Historical TI evidence for 036 QS (Quickstop Super), series 1125 ONLY; not ordinary 036, 034, MS 360 or MS 360 C compatibility. Inspection, maintenance and repair are restricted by the source to properly trained and authorized personnel. This is a source-linked service reference, not a complete repair or operating procedure; all assembly, maintenance and troubleshooting sections must be read together with the original figures. No hardware operation was performed. Exact-model IPL links identify components, not proof that a 2012 part revision existed in 1996.

Source: TI 1/1996, p. 7 — 036 QS outer brake assembly: retain both washer positions.

No additional parts-table entry added.

Service note · 036 QS

036 QS lubrication: solid grease arrows and hollow chain-oil arrows differ

Mobilplex 0781 120 1111 at marked joints; chain oil on the outside diameter of the clutch drum.

  • Section4 figure33 shows the exposed chain-brake linkage and two DIFFERENT arrow styles. SOLID arrows mean grease with Mobilplex 0781 120 1111 at the depicted moving contact/pivot points; HOLLOW arrows mean lubricate with CHAIN OIL on the OUTSIDE DIAMETER OF THE CLUTCH DRUM. The original figure locates the individual points; do not blanket-coat every surface or substitute grease for the specified chain oil.
  • Figure34 separately shows the rear-handle/interlock pivots and contacts with SOLID arrows, also specifying Mobilplex 0781 120 1111. Section3 on page4 requires lubricating all moving parts and explicitly directs the reader to these maintenance arrows.
  • The page7 footnote says owners wishing to run BIOLOGICAL chain oil should use ONLY STIHL Bioplus. This historical restriction is retained; no current product equivalence, alternative lubricant approval, quantity or interval is inferred. The clutch drum OUTSIDE diameter instruction is printed source guidance for this historical QS mechanism, not general advice for other brakes.
  • Historical TI evidence for 036 QS (Quickstop Super), series 1125 ONLY; not ordinary 036, 034, MS 360 or MS 360 C compatibility. Inspection, maintenance and repair are restricted by the source to properly trained and authorized personnel. This is a source-linked service reference, not a complete repair or operating procedure; all assembly, maintenance and troubleshooting sections must be read together with the original figures. No hardware operation was performed. Exact-model IPL links identify components, not proof that a 2012 part revision existed in 1996.

Source: TI 1/1996, p. 4 · TI 1/1996, p. 7 — 036 QS lubrication: solid grease arrows and hollow chain-oil arrows differ.

Part numbers (1)
  • 0781 120 1111 — Mobilplex grease; historical specified productspecified · 036 QS; historical maintenance guidance only

Service note · 036 QS

036 QS fault A: cable travel, pitch contamination and tension-lever rivet play

Four distinct cause/remedy rows; greater than 0.5 mm play is not the cable-travel limit.

  • Fault A is printed BRAKE CANNOT BE ACTIVATED. Row1: free travel <6 mm (0.24 inches), cable stretched → REPLACE BRAKE CABLE. Printed disassembly figures: 1,2,5,7,8,9,10,11,12,13,19; assembly: 33,19,13,12,11,9,10,8,7,34,28,2. Figure33/34 are maintenance references, not unrelated part numbers.
  • Row2: all moving parts on oil-pump housing smeared with PITCH → disassemble, clean and service oil-pump housing (section4). Disassembly: 7–14,16,19,20,21,22,23,24; assembly: 33,24,23,29,30,20,19,32,14,13,12,11,9,10,8,7. Pitch here is contamination, not saw-chain pitch.
  • Row3: rivet on tension lever worn, PLAY >0.5 mm → FIT NEW TENSION LEVER. The inequality is strictly greater than, not greater than or equal to. Disassembly: 7–14,16,19,20; assembly: 33,20,19,14,32,13,12,11,9,10,8,7. No drilling, rivet repair or adjustment is prescribed.
  • Row4: pitch between INSIDE OF COVER AND CLUTCH DRUM → disassemble, clean and service cover and clutch drum (section4). Disassembly: 7–13; assembly: 33,13,12,11,9,10,8,7. Do not merge this contamination location with oil-pump linkage contamination or treat any one row as an exhaustive diagnosis.
  • Historical TI evidence for 036 QS (Quickstop Super), series 1125 ONLY; not ordinary 036, 034, MS 360 or MS 360 C compatibility. Inspection, maintenance and repair are restricted by the source to properly trained and authorized personnel. This is a source-linked service reference, not a complete repair or operating procedure; all assembly, maintenance and troubleshooting sections must be read together with the original figures. No hardware operation was performed. Exact-model IPL links identify components, not proof that a 2012 part revision existed in 1996.

Source: TI 1/1996, p. 1 · TI 1/1996, p. 7 · TI 1/1996, p. 8 — 036 QS fault A: cable travel, pitch contamination and tension-lever rivet play.

No additional parts-table entry added.

Service note · 036 QS

036 QS faults B and C: contamination, broken retaining lug and loose guard

6.5 Nm belongs to the crankcase hex-head screw; both marked screw instructions require Loctite 648.

  • Fault B: brake cannot be activated by INTERLOCK LEVER. Cause: all moving parts on oil-pump housing smeared with pitch. Remedy: disassemble, clean and service oil-pump housing (section4). Disassembly figures: 7–14,16,19,20,21,22,23,24; assembly: 33,24,23,29,30,20,19,32,14,13,12,11,9,10,8,7.
  • Fault C: brake cannot be activated by HAND GUARD. First cause: LUG ON RETAINING LEVER BROKEN → disassemble oil-pump housing and REPLACE RETAINING LEVER. It is not the worn tension-lever rivet in fault A. The same printed figure sequences as the preceding contamination row apply.
  • Second C cause: hand-guard mounting loose. Tighten HEX-HEAD SCREW (CRANKCASE) TO 6.5 Nm. Separately RETIGHTEN SPLINE SCREW IS-M5x30 (2x); the chart supplies NO SEPARATE NUMERICAL TORQUE for those two spline screws. Both instructions carry footnote1: SCREW MUST BE SECURED WITH LOCTITE 648 ADHESIVE. Do not transfer 6.5 Nm to every screw or drop the adhesive requirement.
  • Loose-guard disassembly figures: 7,8,9,15; assembly: 33,15,9,8,7. These are the printed cross-references, not a guarantee the extracted note is a standalone repair procedure.
  • Historical TI evidence for 036 QS (Quickstop Super), series 1125 ONLY; not ordinary 036, 034, MS 360 or MS 360 C compatibility. Inspection, maintenance and repair are restricted by the source to properly trained and authorized personnel. This is a source-linked service reference, not a complete repair or operating procedure; all assembly, maintenance and troubleshooting sections must be read together with the original figures. No hardware operation was performed. Exact-model IPL links identify components, not proof that a 2012 part revision existed in 1996.

Source: TI 1/1996, p. 7 · TI 1/1996, p. 8 — 036 QS faults B and C: contamination, broken retaining lug and loose guard.

No additional parts-table entry added.

Service note · 036 QS

036 QS fault D: broken brake band requires replacement and drum lubrication

Interlock OR hand-guard failure is the printed fault; retain the section4 lubrication reference.

  • Fault D: brake cannot be activated by interlock lever OR by hand guard. Cause: brake band BROKEN. Remedy: FIT NEW BRAKE BAND and LUBRICATE CLUTCH DRUM (see section4). The specified surface/lubricant is the outside diameter with chain oil in figure33, not unspecified grease on every drum surface.
  • Printed disassembly figures: 7–11; assembly: 33,11,9,10,8,7. No band repair, reuse or adjusted stopping-time allowance is supplied. Keep fault A and fault D labels distinct even though their descriptions overlap.
  • Closing imprint: copyright1996 Andreas Stihl; Andreas Stihl D1/MTK-al; Technical Documentation5774. These are source identity marks, not a production serial cutoff or a later revision date.
  • Historical TI evidence for 036 QS (Quickstop Super), series 1125 ONLY; not ordinary 036, 034, MS 360 or MS 360 C compatibility. Inspection, maintenance and repair are restricted by the source to properly trained and authorized personnel. This is a source-linked service reference, not a complete repair or operating procedure; all assembly, maintenance and troubleshooting sections must be read together with the original figures. No hardware operation was performed. Exact-model IPL links identify components, not proof that a 2012 part revision existed in 1996.

Source: TI 1/1996, p. 7 · TI 1/1996, p. 8 — 036 QS fault D: broken brake band requires replacement and drum lubrication.

No additional parts-table entry added.

Service note · 036 QS

036 QS: separate rear-handle brake and three activation paths

Releasing the rear handle stops the chain in less than one second; Quickstop remains distinct.

  • The additional REAR HANDLE BRAKE is described as a SEPARATE SYSTEM. Its activation mechanism is integrated in the throttle-trigger interlock: release of the rear handle automatically locks the chain; pressing the interlock releases it so the throttle can be operated. The two page2 figures explicitly assume QUICKSTOP DISENGAGED. Pressing the interlock is not presented as releasing an engaged front-hand-guard brake.
  • Three braking paths: front-hand-guard inertia in certain sufficiently severe kickback situations; manually pushing the front hand guard toward the bar nose; and manual release of the rear handle. Quickstop stopping is described as within a fraction of a second; the rear-handle brake limit is LESS THAN ONE SECOND. Do not combine these timings, infer protection in every kickback or backdate the numeric limit to earlier QS TIs.
  • Before first operation, the source requires familiarity with this system, especially the owner manual chapters Chain Brake and Starting. Exact 036 QS owner-manual chapters remain a documented source gap. The available 1999-10 034/036/036 QS SERVICE manual is not that owner manual. No starting sequence is invented here.
  • Historical TI 05/1999 USA, 036 QS series 1125 only; not standard 036, 034 or MS 360 retrofit approval. Exact-model 2012 IPL links identify the named subsystem, not proof that its revisions match this 1999 separate rear-handle brake. No serial changeover, complete operating procedure, physical interchange or measured brake performance is established. No hardware operation was performed.

Source: TI 5/1999, p. 1 · TI 5/1999, p. 2 — Complete section 1.1 and operation figures 148TI000/006 KN,including warning.

No additional parts-table entry added.

Service note · 036 QS

036 QS: 5.8 kg specification and two component changes

TI05 lists a strengthened sprocket bearing and ceramic-coated brake band; earlier QS data remains separately dated.

  • TI05 gives standard 036 weight 5.7 kg (12.6 lb) and 036 QS 5.8 kg (12.8 lb), with other specifications described as exactly the same as standard 036. No weighing configuration is stated; do not invent dry/wet or cutting-attachment inclusion, or import unstated numerical standard-036 specifications.
  • Only two main component changes are listed here: strengthened chain sprocket bearing and ceramic-coated brake band. No bearing dimension, band order number, coating specification or retrofit permission is supplied. Omission of other earlier features is not proof that each was removed.
  • CONFLICT / REVISION DIFFERENCE RETAINED: TI45/1995 gives 036 QS 6.0 kg (13.2 lb), not this 5.8 kg (12.8 lb), and lists six architectural changes. No serial boundary, weighing explanation or universal QS configuration reconciles them. The older specification remains unchanged and source-linked.
  • A separate illustrated parts list is specified for 036 QS. Retained SCS 01-2012 exact QS clutch/chain-brake and throttle sheets are navigation only, not the original 1999 separate IPL. Their numbered parts are not assigned to unnumbered TI features; this note does not turn the standard 036 into a QS.
  • Historical TI 05/1999 USA, 036 QS series 1125 only; not standard 036, 034 or MS 360 retrofit approval. Exact-model 2012 IPL links identify the named subsystem, not proof that its revisions match this 1999 separate rear-handle brake. No serial changeover, complete operating procedure, physical interchange or measured brake performance is established. No hardware operation was performed.

Source: TI 5/1999, p. 2 · TI 5/1999, p. 5 — Complete section 1.2 and1.4 separate-IPL statement.

Referenced bulletin evidence: TI 45/1995, p. 3 · TI 45/1995, p. 4 · TI 45/1995, p. 6 — 036 QS modular brake and oil pump: changed hardware, separate IPL.

No additional parts-table entry added.

Service note · 036 QS

036 QS: rear-handle brake check requires under one second

The historical full-throttle check expressly requires bar and chain fitted and trained personnel.

  • Inspections, maintenance and repairs are restricted to properly trained and authorized personnel. If startup is needed during repairs or maintenance, the source requires all local safety regulations AND owner-manual safety precautions. That exact owner manual remains an identified source gap; the service manual is not a substitute.
  • WITH BAR AND CHAIN FITTED, the printed check is: activate throttle to wide open, then LET GO OF THE REAR HANDLE; the chain must come to a standstill in LESS THAN ONE SECOND. This is a historical source description, not a complete startup/bench procedure or authorization to run an unattended test. No repetitions, instrument, timing tolerance or operating-area setup are specified.
  • If the brake fails this check, the source directs servicing the illustrated sliding and pivot points by contamination level, with the separate grease/chain-oil legend preserved in the linked source page. The functional claim has not been measured on hardware.
  • Historical TI 05/1999 USA, 036 QS series 1125 only; not standard 036, 034 or MS 360 retrofit approval. Exact-model 2012 IPL links identify the named subsystem, not proof that its revisions match this 1999 separate rear-handle brake. No serial changeover, complete operating procedure, physical interchange or measured brake performance is established. No hardware operation was performed.

Source: TI 5/1999, p. 3 — Section1.3 and1.3.1 opening safety restrictions and complete functional check.

No additional parts-table entry added.

Service note · 036 QS

036 QS: solid grease arrows differ from hollow chain-oil arrows

Mobilplex 0781 120 1111 goes on marked joints; chain lubricant coats the clutch-drum circumference.

  • If brake function is improper: SLIGHT contamination calls for a suitable brush and mineral spirit to clean all parts. HEAVY contamination or resin clogging calls for disassembling the parts, cleaning with mineral spirit or resin solvent, replacing worn/damaged parts, and cleaning housing recesses before reinstallation. No chemical substitution, soaking time or unsourced disassembly sequence is given.
  • In BOTH cleaning cases, SOLID black arrows in figures 148TI007 KN (rear handle) and 148TI008 KN (brake mechanism) mean Mobilplex 0781 120 1111 grease. HOLLOW arrows mean CHAIN LUBRICANT on the CIRCUMFERENCE OF THE CLUTCH DRUM. Original figures locate the points; no arrow is assigned an invented component number. Do not grease the whole drum, replace grease with oil at every pivot, or generalize this historical QS instruction to other chain brakes.
  • Quality chain lubricant is required. If a biological lubricant is preferred, TI05 RECOMMENDS STIHL Bioplus; the recommendation also applies to the moving-system maintenance. Unsuitable oils can produce resin buildup and premature brake failure. The footnote requires original STIHL replacement parts from the current parts list.
  • Wording difference retained: TI01/1996 says use ONLY STIHL Bioplus for biological oil, while TI05/1999 says RECOMMEND. This note preserves each dated statement without inventing a current substitute approval or silently rewriting the earlier restriction.
  • Historical TI 05/1999 USA, 036 QS series 1125 only; not standard 036, 034 or MS 360 retrofit approval. Exact-model 2012 IPL links identify the named subsystem, not proof that its revisions match this 1999 separate rear-handle brake. No serial changeover, complete operating procedure, physical interchange or measured brake performance is established. No hardware operation was performed.

Source: TI 5/1999, p. 2 · TI 5/1999, p. 3 — Chain Lubrication and complete service cleaning branches,figures 148TI007/008 KN,legend and starred footnote.

Referenced bulletin evidence: TI 1/1996, p. 4 · TI 1/1996, p. 7 — 036 QS lubrication: solid grease arrows and hollow chain-oil arrows differ.

Part numbers (1)
  • 0781 120 1111 — Mobilplex grease; solid-arrow jointsHistorical specified material; no substitute inferred · 036 QS; exact TI05/1999 locations only

Service note · 036 QS

036 QS: M8×22 brake-band mounting torque and adhesive

The single listed joint requires 10 Nm (7.5 lbf.ft) with 0786 111 2101, printed LOCTITE 242.

  • The only table row is TORX M8 x 22, BRAKE BAND MOUNTING/CRANKCASE, 10 Nm (7.5 lbf.ft), remark 1. Remark1 requires adhesive 0786 111 2101 (LOCTITE 242). Preserve both printed torque units; this row is not an M8 general torque table.
  • The source supplies NO screw order number. In particular, the later exact-model IPL screw 1125 162 9300 is not dimensioned here; no identity or torque transfer to that part is inferred. ALL OTHER PARTS AS BEFORE is retained as a cross-reference, not an instruction to apply 10 Nm or this adhesive to all fasteners.
  • TI45/1995 lists four DIFFERENT joints and labels adhesive 0786 111 1101 LOCTITE242 (itself conflicting with TI43/1995 Loctite243). TI05 here prints 0786 111 2101 LOCTITE242. These are distinct printed numbers/joints; no equivalence, supersession or resolution of the older label conflict is inferred.
  • Historical TI 05/1999 USA, 036 QS series 1125 only; not standard 036, 034 or MS 360 retrofit approval. Exact-model 2012 IPL links identify the named subsystem, not proof that its revisions match this 1999 separate rear-handle brake. No serial changeover, complete operating procedure, physical interchange or measured brake performance is established. No hardware operation was performed.

Source: TI 5/1999, p. 4 — Section1.3.2 torque table,all-other-parts line and remark 1.

Referenced bulletin evidence: TI 45/1995, p. 5 — 036 QS four torque rows: Loctite 648 and printed Loctite 242 labels.

Part numbers (1)
  • 0786 111 2101 — Adhesive; printed LOCTITE 242 for M8×22 jointHistorical specified material; no substitute inferred · 036 QS; exact TI05/1999 locations only

Service note · 036 QS

036 QS: preserve existing DG threads and avoid polymer overheating

Re-engage the existing thread before tightening; the M8 table value is not a blanket DG torque.

  • Self-tapping DG screws form a permanent thread in polymer on first installation. Repeated removal/reinstallation without loss of assembly strength is conditional on observing the specified tightening torque with a TORQUE WRENCH; it is not proof that damaged threads can be reused.
  • For an existing DG thread, position the screw, turn COUNTERCLOCKWISE until it drops slightly, then tighten CLOCKWISE to the specified torque. This engages the original thread instead of cutting another and weakening the assembly. The separate M8 x22 brake-band row does not supply a universal DG torque.
  • Adhesive-secured screws are easier to release after warming the area with a hot-air blower (hair dryer). The source explicitly warns NOT TO OVERHEAT POLYMER COMPONENTS. No temperature, duration or open-flame method is specified.
  • Historical TI 05/1999 USA, 036 QS series 1125 only; not standard 036, 034 or MS 360 retrofit approval. Exact-model 2012 IPL links identify the named subsystem, not proof that its revisions match this 1999 separate rear-handle brake. No serial changeover, complete operating procedure, physical interchange or measured brake performance is established. No hardware operation was performed.

Source: TI 5/1999, p. 4 — Section1.3.2 DG-screw paragraphs,three-step sequence and hot-air note.

No additional parts-table entry added.

Service note · 036 QS

036 QS: 1999 repair allowances are tenths of an hour

The 19 printed rows use hours; code 19 is absent, and code 10 retains its repair-attempt exception.

  • These historical allowances assume trained personnel in a properly equipped service workshop, in TENTHS OF AN HOUR (0.1 = 6 minutes). The cut-out or hand-transcription note supplements the contemporary repair-times table. These are not measured owner durations, present billing commitments or brake test hold times.
  • Codes 1–6: (1) crankcase, crankshaft, crank bearings, crankcase gasket 2.3 h; (2) cylinder shroud 0.3 h; (3) anti-vibration buffers 0.7 h; (4) crankshaft seals 1.0 h; (5) cylinder and/or piston 1.3 h; (6) ignition module 0.5 h.
  • Codes 7–12: (7) fuel hose 0.5 h (source prints Fule Hose); (8) carb flange or connector 0.7 h; (9) repair/rebuild carburetor 0.8 h; (10) replace carburetor or carburetor jet 0.4 h, BUT IF TRIED TO REPAIR USE CODE 9; (11) oil pump or oil line 0.7 h; (12) recoil starter 0.5 h. The code 10 exception is not permission to add 0.4 h and 0.8 h.
  • Codes 13–18 and20: (13) clutch 0.5 h; (14) chain brake 0.9 h; (15) muffler 0.4 h; (16) air filter, filter cover, tank cap, tank vent, fuel filter, oil filter, spark plug, deco valve, cutting attachment or miscellaneous minor repairs 0.3 h; (17) stop switch or control lever 0.5 h; (18) fuel tank/handle assembly 0.8 h; (20) all other repairs 0.5 h. CODE 19 IS NOT PRINTED; it is not a zero allowance or an invented repair category.
  • TI45/1995 uses a DIFFERENT 20-code MINUTES table (chain brake code 17, 35 minutes); this 1999 table uses chain brake code 14, 0.9 h. Do not merge by code or treat the later number as a conversion of the older allowance. No loaded-test asterisks or additional test-run requirements are printed in the TI05 table.
  • Historical TI 05/1999 USA, 036 QS series 1125 only; not standard 036, 034 or MS 360 retrofit approval. Exact-model 2012 IPL links identify the named subsystem, not proof that its revisions match this 1999 separate rear-handle brake. No serial changeover, complete operating procedure, physical interchange or measured brake performance is established. No hardware operation was performed.

Source: TI 5/1999, p. 5 — Complete section 1.3.3 table,conditions,cut-out note and footer context.

Referenced bulletin evidence: TI 45/1995, p. 6 — 036 QS historical repair times: two dashes and six loaded-test marks.

No additional parts-table entry added.

Service note · 036 QS

036 QS: brake-interlock free-travel check and adjustment

The QS check requires a slack brake cable, a snug band at points A and interlock travel within marked range B. Clockwise adjustment reduces free travel; counterclockwise increases it.

  • TI31/1999 explicitly covers model 036 QS, series 1125. The exact QS clutch/chain-brake and pickup-body/air-filter assemblies are linked for this service context only; ordinary 036/034, later MS variants and replacement-part interchange are not inferred. No part numbers or production changeover are specified.
  • Section 1 preparations: pull the hand guard toward the front handle to release the chain brake; release/remove the hexagon nuts and chain sprocket cover; remove the bar and chain. Remove screw(1), side plate(2), spline socket head screws(3) and cover(4), following drawing 148TI012 KN. Illustration numbers are local callouts, not catalog part numbers or IPL positions.
  • With the brake off, the brake cable(5) must hang loosely in the crankcase, with no tension (148TI013 KN). Press interlock lever(6) down all the way and hold it there (148TI014 KN). In that condition, brake band(7) must locate snugly, with no play, against the crankcase points marked A in 148TI015 KN. Do not replace these separate cable/band requirements with a generic cable-tension adjustment.
  • Release interlock lever(6), then press it down slowly to check free travel. Travel must be within range B marked on the front end of the lever in 148TI016 KN; the brake band’s brake lever must not move during that free travel. The source supplies a graphical/marked range, not a millimeter or angle value. Do not measure the scan to invent a clearance. Adjust as necessary using section 2.
  • Section 2 access: release twist lock(1) and remove carburetor box cover(2) (148TI017 KN); release/remove slotted nuts(3) and air filter(4) (148TI018 KN). The section 2 callouts restart independently: they are not the section 1 side-plate screw, cover or interlock lever.
  • Loosen clamp screw(5), then use a 6 mm open-end wrench on adjusting nut(6), as shown in 148TI019 KN. Turn the nut clockwise (right) to reduce free travel or counterclockwise (left) to increase it. The 6 mm value is wrench size, not the amount of free travel or a thread dimension. Section 2 nut(6) is not section 1 interlock lever(6).
  • Lock the adjusting nut in position with clamp screw(5). Reassemble all parts in the reverse sequence. The bulletin supplies no numeric clamp-screw torque, turn count, braking-time acceptance value or complete post-repair safety test; none is fabricated from the illustration or transferred from another model.
  • The final line identifies TI05/1999 as the previous Technical Information on 036 QS; it is a chronology pointer, not an instruction to replace this adjustment with an earlier procedure. Its already-recorded source gaps/conflicts remain unchanged. No additional delegated procedure is required by TI31’s text. This note records historical source instructions only: no brake adjustment, machine operation or repair acceptance was performed.

Source: TI 31/1999, p. 1 · TI 31/1999, p. 2 · TI 31/1999, p. 3 — Complete sections 1–2 across pages 1–3: preparations, cable slack, band points A, marked free-travel range B, adjustment and reassembly; drawings 148TI012–019 KN.

No additional parts-table entry added.

Wrong number or missing part for the 036 QS? Report a correction →