← 044/046 · MS 440/460/461

Stihl 1128 · Section E · 5 of 16 · 38 parts

Chain brake, Chain sprocket cover

Fits 046.

Parts diagrams →

Historical fitment & changes (7) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
110101112131415161718181819220212223242526272933031323334353644056789
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (38)

PosPart numberDescriptionQty
1 1128 790 9152 Hand guard Fitment / change note → 1
2 1124 084 8300 Reflector foil 1
3 1124 792 5500 Bushing Fitment / change note → 1
4 1124 792 5505 Bushing Fitment / change note → 1
5 9022 341 1080 Spline screw IS-M5x35 Fitment / change note → 1
6 1128 790 9153 Hand guard 1
7 1128 084 8304 Reflector foil 1
8 1128 792 0900 Reflector foil 1
9 1128 160 5000 Lever 1
10 9460 624 0400 E-clip 4 2
11 1121 162 5010 Lever 1
12 0000 997 0628 Spring 1
13 1128 160 5400 Brake band 1
14 1128 160 5501 Tension spring 1
15 1128 162 8000 Hose 1
16 1128 021 1101 Cover 1
17 1128 021 1105 Cover 1
18 9022 313 0660 Spline screw IS-M4x12 4
19 1125 640 1701 Chain sprocket cover → replaced by 1122 640 1702, 1128 640 1706 TI 36/2000 1
20 1125 656 1501 Guard 1
21 1121 648 6610 Bumper strip 2
22 1122 648 0403 Chain sprocket cover Fitment / change note → 1
23 1122 656 1510 Guard 1
24 1128 664 0501 Bumper spike 1
25 9008 319 0960 Hexagon head screw M5x12 2
26 9214 320 0700 Lock nut M5 3
27 1122 650 7700 Chain catcher 1
29 1128 664 0500 Bumper spike 1
30 9022 341 0960 Spline screw IS-M5x12 → replaced by 9022 341 0980 TI 3/2006 1
31 1122 656 7700 Chain catcher 1
32 9022 341 1019 Spline screw IS-M5x20 1
33 0000 955 0801 Hexagon nut M8 2
34 9214 320 0700 Lock nut M5 1
35 0000 967 3714 Instruction label ARCTIC 1
36 0000 967 3612 Instruction label 1
40 0000 790 6103 Screw assy. M5 Fitment / change note → 1
Not numbered on the diagram — assemblies, kits and options
— 1128 640 1707 Chain sprocket cover Fitment / change note → 1
— 1128 640 1708 Chain sprocket cover Fitment / change note → 1

Parts are not interchangeable across engine series — check yours before ordering.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · 046

046: hand-guard replacement needs both bushings and screw

Interchangeability applies to the complete new hand guard, with its brass bushing, rubber bushing and M5×35 screw.

  • For 046, replace 1128 790 9102 with complete hand guard 1128 790 9152; the 044 and 046 guards have different numbers.
  • Fit both bushings (1124 792 5500 and 1124 792 5505) and screw 9022 341 1080. The brass-bushing flange points inward.
  • Do not infer bare-guard interchange using the old mounting hardware. Introduction was in progress; no numeric serial is supplied.
  • The new guard is supported in a rubber bushing on the fan side. Before installation, push brass bushing (2) into rubber bushing (3), then fit both into guard (1), brass flange inward, and secure with M5 × 35 screw (4). The source calls original and complete new assemblies fully interchangeable within the stated model; it does not permit bare-guard substitution.
  • The table includes bushings and screw with each new guard. Original guards remain factory-supplied only while stocks last. Old screw-and-washer assembly 0000 790 6103 remains available as a spare for other models, not as the new guard fastener; those other models are not identified.

Source: TI 47/1997, p. 9 · TI 47/1997, p. 10 — Section 6: front hand guard and summary; full section, drawing and summary context reviewed in batch26.

Part numbers (6)
  • 1128 790 9102 — Hand guardOriginal equipment · 046
  • 1128 790 9152 — Hand guardConditional replacement · 046 complete with both bushings and screw
  • 1124 792 5500 — Brass bushingRequired companion · 046 new guard, flange inward
  • 1124 792 5505 — Rubber bushingRequired companion · 046 new guard
  • 9022 341 1080 — IS M5×35 screwRequired companion · 046 new guard
  • 0000 790 6103 — Original screw and washer assemblyHistorical original mounting hardware · Retained for unnamed other models; not new guard installation

Conditional replacement · 046

046: spike/catcher cover replacement named in 2007 summary

TI 15/2007 summary explicitly names 046 alongside MS 460 for 1128 640 1701 → 1128 640 1707; the new version is listed as a spare for older machines.

  • TI 15/2007 summary explicitly names 046 alongside MS 460 for 1128 640 1701 → 1128 640 1707; the new version is listed as a spare for older machines.
  • Old covers without countersunk holes require old collar screws 0000 953 6605. New countersunk covers accept either screw type; old covers must not be combined with 1138 664 2400.
  • This record is the cover with bumper spike and chain catcher, not the wrap-handle or rescue cover.
  • This explicit 046 cover row does not establish 046 applicability for the bulletin’s MS 440 / MS 460 crankcases, MS 460 handle changes or clutch-side bearing.
  • When changing cover geometry, the source’s section 1.3 lug-free side-plate service condition remains relevant; this is not permission to retain an incompatible lugged plate.
  • Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.

Source: TI 15/2007, p. 1 · TI 15/2007, p. 2 · TI 15/2007, p. 3 · TI 15/2007, p. 4 · TI 15/2007, p. 8 — Sections 1.2–1.3 and summary row 5; explicit 046 scope.

Part numbers (4)
  • 1128 640 1701 — Sprocket cover with spike/catcherPrevious version · Previous cover configuration
  • 1128 640 1707 — Sprocket cover with spike/catcherRevised version · 046 spike/catcher configuration
  • 0000 953 6605 — Collar screwPrevious version · Old or new countersunk cover
  • 1138 664 2400 — Collar screwNew version · Countersunk cover only

Conditional replacement · 046

046: wrap-handle cover replacement named in 2007 summary

TI 15/2007 summary explicitly names 046 alongside MS 460 for 1128 640 1700 → 1128 640 1708; the new version is listed as a spare for older machines.

  • TI 15/2007 summary explicitly names 046 alongside MS 460 for 1128 640 1700 → 1128 640 1708; the new version is listed as a spare for older machines.
  • Old covers without countersunk holes require old collar screws 0000 953 6605. New countersunk covers accept either screw type; old covers must not be combined with 1138 664 2400.
  • Wrap handles require the outward-projecting extended lower section. New assembly 1128 640 1708 includes item 6, cover 1122 648 0403; do not substitute a standard cover.
  • This explicit 046 cover row does not establish 046 applicability for the bulletin’s MS 440 / MS 460 crankcases, MS 460 handle changes or clutch-side bearing.
  • When changing cover geometry, the source’s section 1.3 lug-free side-plate service condition remains relevant; this is not permission to retain an incompatible lugged plate.
  • Retained edition: English USA. Introduction is continuous, with no numeric serial cutoff. Historical availability is not current stock or universal regional applicability.

Source: TI 15/2007, p. 1 · TI 15/2007, p. 2 · TI 15/2007, p. 3 · TI 15/2007, p. 4 · TI 15/2007, p. 8 — Sections 1.2–1.3 and summary rows 6–7; explicit 046 scope.

Part numbers (6)
  • 1128 640 1700 — Sprocket cover for wrap handlePrevious version · Previous cover configuration
  • 1128 640 1708 — Sprocket cover for wrap handleRevised version · 046 wrap-handle configuration
  • 1122 648 0401 — Sprocket cover for wrap handlePrevious version · Previous cover configuration
  • 1122 648 0403 — Sprocket cover for wrap handleRevised version · 046 wrap-handle configuration
  • 0000 953 6605 — Collar screwPrevious version · Old or new countersunk cover
  • 1138 664 2400 — Collar screwNew version · Countersunk cover only

Historical fitment · 046

046: Plastoform refitting and workshop-tool limits

Re-engage the existing polymer thread and tighten with a torque wrench; the T-handle is release-only on Plastoform screws.

  • For refitting a Plastoform screw, rotate counterclockwise until it drops into the existing thread, then tighten clockwise to the specified torque. This avoids forming a second thread; no new-hole torque is supplied here.
  • The QI-T27x 150 T-handle is for releasing only on Plastoform screws. The roster calls for a torque wrench when tightening them. Optical/acoustic signalling is specifically noted for wrench 0302 and 0312.
  • The lower wrench range is printed as 0.5–18 Nm (0.325–13.5 lbf.ft), the higher as 6–80 Nm (4.5–60 lbf.ft). Preserve printed units/rounding; these ranges are not component torque values.
  • Hot air is described as an aid to releasing adhesive-secured screws, with explicit care around polymer components. No temperature or heating duration is specified.
  • The assembly tube 1117 890 0900 appears twice, once for brake springs and once for clutch springs. The stand/clamping-bar pairing is historical 046 guidance, not resolution of the later support-kit screw conflict.

Source: TI 46/1995, p. 8 · TI 46/1995, p. 12 — 4.1 remarks and5.3 continuation: general tools and existing threads.

Part numbers (17)
  • 1117 890 0900 — Assembly tube, brake and clutch springsListed tool application · 046
  • 5910 893 0501 — M8 bar-stud pullerListed tool application · 046
  • 1111 890 6400 — Ignition air-gap gaugeListed tool application · 046
  • 1116 893 4800 — Rewind-spring assembly toolListed tool application · 046
  • 5910 893 8800 — Fuel-pickup assembly hookListed tool application · 046
  • 5910 890 3100 — Assembly standListed tool application · 046
  • 5910 890 2005 — Clamping bar for mounting sawListed tool application · 046
  • 5910 890 0301 — Torque wrench, lower rangeListed tool application · 046
  • 5910 890 0302 — Torque wrench, lower range with signalListed tool application · 046
  • 5910 890 0311 — Torque wrench, higher rangeListed tool application · 046
  • 5910 890 0312 — Torque wrench, higher range with signalListed tool application · 046
  • 5910 890 2400 — QI-T27x 150 T-handleListed tool application · 046
  • 5910 890 8210 — Electrical connector crimping toolListed tool application · 046
  • 1110 893 4500 — Flywheel pullerListed tool application · 046
  • 5910 893 5608 — 13 mm flywheel-nut socketListed tool application · 046
  • 5910 893 5613 — 19 mm clutch socketListed tool application · 046
  • 0812 542 2104 — T27x 125 IS screwdriverListed tool application · 046

Service note · 046

046: small-fastener torques, adhesives and ignition washer

The ignition-module screws require both Loctite 242 and a washer; nearby screws have different requirements.

  • These are historical TI 46/1995 page 11 fastener-specific values, not universal torque by thread diameter. No fastener part number is supplied. Printed lbf.ft equivalents are retained alongside Nm.
  • Generator IS-M4×12: 3.5 Nm (2.6 lbf.ft), Loctite 649. Chain-tensioner cover plate IS-M4×8: 3 Nm (2.2 lbf.ft).
  • IS-M4×12 oil-pump cover at sprocket side: 3 Nm (2.2 lbf.ft); brake-band/crankcase: 3 Nm (2.2 lbf.ft), Loctite 242; oil pump: 3.5 Nm (2.6 lbf.ft).
  • IS-M4×12 segment/fan housing: 2.5 Nm (1.8 lbf.ft); sprocket-side crankcase cover: 3 Nm (2.2 lbf.ft).
  • M5 SK6 collar nut for carburetor/filter base/flange: 6 Nm (4.4 lbf.ft), remark 3/Loctite 270. The table calls the fastener a collar nut although its remark generically says screw; neither label is silently changed.
  • Fan housing IS-M5×20: 7 Nm (5.2 lbf.ft). Ignition module/crankcase IS-M5×20: 7 Nm (5.2 lbf.ft), Loctite 242 AND a washer under the screw head. Do not transfer this washer requirement to every M5 screw.

Source: TI 46/1995, p. 11 — 5.3: M4 rows, intake collar nut, fan housing and ignition.

No additional parts-table entry added.

Service note · 046

046: handle, buffer and cutting-attachment fastener torques

Handle, AV-buffer, bumper and chain-catcher rows keep distinct torques even when thread sizes match.

  • These are historical TI 46/1995 page 11 fastener-specific values, not universal torque by thread diameter. No fastener part number is supplied. Printed lbf.ft equivalents are retained alongside Nm.
  • Switch housing B2.9×9.5: 1 Nm (0.75 lbf.ft); handle molding B3.9×19: 1.6 Nm (1.2 lbf.ft). Buffer/crankcase IS-M4×16: 5 Nm (3.7 lbf.ft), Loctite 242.
  • Spiked bumper top with nut IS-M5×12: 7.5 Nm (5.5 lbf.ft); bottom bumper/chain catcher IS-M5×16: 7.5 Nm (5.5 lbf.ft).
  • Wrap-around handle with bracket IS-M5×20: 7 Nm (5.2 lbf.ft); left hand guard IS-M5×30: 7 Nm (5.2 lbf.ft).
  • Front handle top/bottom IS-P6×19: 8 Nm (5.9 lbf.ft), Loctite 649. Front and rear buffer/tank-housing IS-P6×19: 5.5 Nm (4 lbf.ft); rear-left buffer/tank-housing IS-P6×32.5: 5.5 Nm (4 lbf.ft). Reuse the existing Plastoform thread as page 12 directs.
  • Self-locking M5 nut for spiked bumper: 7.5 Nm (5.5 lbf.ft); self-locking M5 nut for chain catcher/spiked bumper: 6 Nm (4.4 lbf.ft). These are separate rows, not interchangeable tightening values.
  • The guide-bar collar-nut row prints M8×21.5,23 Nm (17 lbf.ft), remark 2/Loctite 242. That unusual adhesive assignment is retained as printed, not generalized to all bar nuts or silently removed; verify the exact repair context before applying it.

Source: TI 46/1995, p. 11 · TI 46/1995, p. 12 — 5.3: handles, buffers, bumper, guard and guide-bar rows.

No additional parts-table entry added.

Service note · 046

046: limited 044 assembly inheritance, not blanket interchange

The release carries over clutch, rewind starter and chain brake from 044; other parts are described as revised.

  • The source says 044 repair times also apply to 046, but gives no numeric times. Those allowances cannot be reconstructed from this page.
  • Only clutch, rewind starter and chain brake are named as taken from 044. All other parts are described as revised/new and the reader is directed to the IPL. This is a release-level assembly statement, not proof that every internal part or later revision interchanges.
  • The document is dated September 5,1995. That evidence date is not a serial changeover, production start for every market, or the 2026 review date.

Source: TI 46/1995, p. 12 — 5.4 and6: repair times and spare-parts scope.

No additional parts-table entry added.

Wrong number or missing part for the 046? Report a correction →