Stihl 1128 · Section F · 6 of 16 · 20 parts
Ignition system
Fits 046.
Historical fitment & changes (11) — includes parts and conditions not shown on this drawing.
Parts (20)
| Pos | Part number | Description | Qty |
|---|---|---|---|
| 1 | 1128 400 1211 | Flywheel Fitment / change note → | 1 |
| 2 | 1128 400 1212 | Flywheel Fitment / change note → → replaced by 1128 400 1203 TI 28/1999 | 1 |
| 3 | 1128 400 1203 | Flywheel Fitment / change note → | 1 |
| 4 | 0000 955 0802 | Collar nut M8x1 | 1 |
| 5 | 1128 404 3501 | Generator Fitment / change note → → replaced by 1128 404 3502 TI 37/1999 | 1 |
| 6 | 1128 404 3502 | Generator Fitment / change note → | 1 |
| 7 | 1118 431 6600 NLA | Terminal pin no longer available from factory | 1 |
| 8 | 1118 431 6700 NLA | Terminal socket no longer available from factory | 1 |
| 9 | 9022 313 0660 | Spline screw IS-M4x12 | 3 |
| 10 | 1122 400 1314 | Ignition module Fitment / change note → | 1 |
| 11 | not sold separately | Ignition lead 150 mm not available as a separate item | 1 |
| 12 | 0000 448 1250 | Lead retainer | 1 |
| 13 | 0000 989 1010 | Grommet | 1 |
| 14 | 1122 442 0400 | Insulating hose 100 mm / 4'' | 1 |
| 15 | 9022 341 1019 | Spline screw IS-M5x20 | 3 |
| 20 | 9291 021 0120 | Washer 5.3 | 3 |
| 21 | 1128 404 3501 | Generator Fitment / change note → → replaced by 1128 404 3502 TI 37/1999 | 1 |
| 22 | 1128 400 1212 | Flywheel Fitment / change note → → replaced by 1128 400 1203 TI 28/1999 | 1 |
| Not numbered on the diagram — assemblies, kits and options | |||
| — | 0000 405 0600 NLA | Ignition lead 1 m not illustratedoption | 1 |
| — | 0000 930 2251 | Ignition lead 10 m not illustratedoption | 1 |
Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.
Historical fitment & changes
Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.
Historical fitment · 046
046: ignition module revision
Historical TI 47/1997 recommendation only: later TI 22/1998 splits the universal-module rule by model. Read the linked later guidance.
Later reviewed guidance: 046: later ignition guidance replaces the universal-module rule
- Later TI 22/1998 revises this recommendation. Do not use this 1997 record alone to select a replacement module.
- 046: 0000 400 1303 → 0000 400 1305.
- The new module has a two-arm yoke without timing adjustment. Do not carry the old 046 three-arm timing-adjustment feature over to it.
- The word universal in this bulletin is not proof of compatibility with unlisted models. Introduction was in progress; no numeric cutoff is supplied.
- The 046 original three-arm module has timing adjustment; the replacement has two arms and no timing adjustment. Drawing132TI021 identifies original (1) and new (2).
- Original module remains factory-supplied only while stocks last. The cover expressly excludes section5.2 from the modifications described as achieving EPA compliance; replacement alone is not an EPA-conversion claim. Later TI22/1998 guidance remains attached and takes precedence for selection.
Source: TI 47/1997, p. 1 · TI 47/1997, p. 9 — Sections 5.2–5.3: ignition module and summary; full section, drawing and summary context reviewed in batch26.
Part numbers (2)
- 0000 400 1303 — Ignition moduleOriginal version · 046
- 0000 400 1305 — Two-arm ignition moduleNew version · 046; no timing adjustment
Conditional replacement · 046
046: later ignition guidance replaces the universal-module rule
TI 22/1998 splits the former 1305 replacement by model after field reliability problems; this is later guidance than TI 47/1997.
- The later reviewed replacement for 046 is 1122 400 1314. Do not automatically cross-reference 0000 400 1305 to one number for every model.
- Existing stocks of 0000 400 1305 may still be used in the 046; new orders in this bulletin use 1122 400 1314.
- The separate 064 and 066 previous-module/serial restrictions are not 044 or 046 cutoffs. This record does not approve those other models.
- Introduction is in progress; no numeric 044/046 cutoff is stated. This is dated historical service guidance, not proof of the latest available module.
- The 046/066 branch originated with the lightweight polymer flywheel; the integrated-lead construction description belongs to the reactivated 1300 branch, not a stated 1314 dimension.
- TI22/1998 reports isolated reliability problems with the former universal module on aluminium-flywheel machines. Different timing requirements led to two optimized modules; this is historical manufacturer field-test guidance, not a project hardware test.
- Order only 0000 400 1300 or 1122 400 1314 according to the named model and restrictions. There is no automatic one-number replacement for 0000 400 1305.
- The 02.98 microfiche/CD-ROM issue documents the future part numbers. Both summary rows say the original 0000 400 1305 is no longer available from the factory; that does not revoke the expressly permitted use of existing stocks on eligible 046/066 machines.
- Introduction is in progress, without a new production cutoff. Factory availability is a 1998 statement, not current stock or proof of physical interchange.
Source: TI 22/1998, p. 1 · TI 22/1998, p. 2 — Sections 1–6: history, split, service note and ordering.
Part numbers (2)
- 0000 400 1305 — Former universal ignition moduleEarlier recommendation · 046; read later model-specific service guidance
- 1122 400 1314 — Model-specific ignition moduleLater reviewed replacement · 046 under TI 22/1998
Service note · 046
046: original engine dimensions and construction
The 1995 046 specification is 76.5 cm³, 52 mm bore and 36 mm stroke; it is not a 044 interchange claim.
- Compared with 044, the bulletin describes a wider big-end bearing, stronger crankcase, revised intake flange/baffle, cylinder cooling area increased by 10%, modified shroud/outlet plate and redesigned vibration buffers. No replacement numbers or retrofit permission are given.
- The composite flywheel uses a steel hub, polymer fan, high-power magnets and magnesium starter-pawl bushing. Claimed weight reduction is about 30%, with cooling-air flow increased by 30%; these are source comparisons, not measurements made by this project.
- The cylinder/crankcase uses 6 mm mounting screws and a sheet-steel gasket. The engine is a single-cylinder two-stroke with specially impregnated bore; compression ratio 9.6: 1. Three-part drop-forged crankshaft, two deep-groove main bearings, needle-cage big and small ends, 62 mm connecting rod and 12 mm piston pin are specified.
- Rated power is 4.4 kW (5.9 bhp) at 9,500 rpm; maximum torque is 4.8 Nm (3.54 lb.ft) at 6,500 rpm. Maximum permissible speed is 13,500 rpm WITH Rollomatic bar and chain, not an unloaded powerhead test limit. Mean idle is 2,500 rpm.
- The unlined centrifugal clutch is 76 mm diameter and engages at approximately 3,500 rpm. The ElastoStart rewind mechanism uses pawl engagement and 3.5 mm starter rope.
- Powerhead weight excluding cutting attachment is 6.5 kg (14.3 lb). The page separately prints power-to-weight ratio 2.55 lbs/bhp; this does not agree with the printed 14.3 lb and 5.9 bhp (about 2.42). Preserve the discrepancy, not a silently recalculated replacement.
- Specifications describe this historical 046 release; they do not identify all later 046/MS 460 variants or establish interchangeable engine, flywheel or AV parts.
Source: TI 46/1995, p. 1 · TI 46/1995, p. 3 · TI 46/1995, p. 5 · TI 46/1995, p. 6 · TI 46/1995, p. 7 — 1.3–1.5,1.8–1.9,1.11,2.1,2.4: original construction and specifications.
No additional parts-table entry added.
Service note · 046
046: historical carburetor and ignition specifications
The original fuel and ignition settings are release-specific reference data, not universal replacement-carburetor settings.
- The original all-position diaphragm carburetor has an integral fuel pump; standard H and L settings are each one turn open. No carburetor type or limiter configuration is specified, so these settings are not assigned to every carburetor listed on the linked later IPL sheets.
- Fuel capacity is 0.94 l (2 US pt). The 1995 source specifies minimum pump octane 89 unleaded, 50: 1 with STIHL 50: 1 two-stroke oil, and 25: 1 with other brand-name air-cooled two-stroke oils. This is historical formulation-dependent guidance, not a new recommendation for current oils.
- Breakerless electronic magneto ignition: module/flywheel air gap 0.15–0.30 mm (0.006–0.012 in), timing 2.0–3.0 mm (0.080–0.12 in) before top dead center.
- Suppressed Bosch WSR 6 F spark plug: 0.5 mm (0.020 in) electrode gap, M14 × 1.25 thread, 9.5 mm (0.37 in) thread length and printed heat range 200. No alternative plug or STIHL part number is inferred.
Source: TI 46/1995, p. 6 · TI 46/1995, p. 7 — 2.2–2.3: fuel, ignition and spark-plug specification.
No additional parts-table entry added.
Historical fitment · 046
046: original servicing aids and adhesive distinctions
Lubricants have separate stated applications; Loctite 242,270 and 649 are not presented as interchangeable.
- Lubricating grease 0781 120 1111 is listed for oil seals, oil-pump drive and sprocket bearing. The same application column also prints “Cleaning crankshaft stub” without a separately named cleaner. Preserve that anomalous row; do not infer grease is a cleaning solvent.
- Special lubricant 0781 417 1315 is for the rope-rotor bearing bore and starter-cover rewind spring. Multipurpose grease 0781 120 1109 is for the ignition module high-voltage output.
- The electrician’s repair kit has no contents/application detail on this page. Gasket panel 0457 281 1704 is labeled 044/046, not a claim that their cylinder gaskets interchange.
- The source lists medium-strength Loctite 242 and high-strength 270/649. Component-specific page 11 remarks determine which is called for; later formulation equivalents are not established.
Source: TI 46/1995, p. 9 · TI 46/1995, p. 11 — 4.2 and5.3 remarks: servicing aids and adhesive assignments.
Part numbers (5)
- 0781 120 1111 — Lubricating greaseHistorical servicing aid · 046 roster; no current substitute inferred
- 0781 417 1315 — STIHL special lubricantHistorical servicing aid · 046 roster; no current substitute inferred
- 0000 007 1013 — Electrician’s repair kitHistorical servicing aid · 046 roster; no current substitute inferred
- 0781 120 1109 — STIHL multipurpose greaseHistorical servicing aid · 046 roster; no current substitute inferred
- 0457 281 1704 — Gasket panel 044/046Historical servicing aid · 046 roster; no current substitute inferred
Service note · 046
046: engine fasteners and catalytic-muffler torque branches
Cylinder, crankcase, flywheel, clutch and muffler values retain thread and variant distinctions.
- These are historical TI 46/1995 page 11 fastener-specific values, not universal torque by thread diameter. No fastener part number is supplied. Printed lbf.ft equivalents are retained alongside Nm.
- Cylinder/crankcase IS-M6×25: 15 Nm (11 lbf.ft); crankcase IS-M5×20: 11.5 Nm (8.5 lbf.ft); shroud/crankcase IS-M5×16: 7 Nm (5.2 lbf.ft).
- Standard muffler top IS-M5×6: 6.5 Nm (4.8 lbf.ft), Loctite 242; muffler/cylinder IS-M5×16: 11.5 Nm (8.5 lbf.ft), Loctite 242.
- Kat/catalytic muffler top IS-M5×30: 6.5 Nm (4.8 lbf.ft), Loctite 242; Kat muffler/cylinder IS-M6×18: 15 Nm (11 lbf.ft), Loctite 242. Separate muffler/crankcase IS-M6×18 row: 15 Nm (11 lbf.ft), with no adhesive remark printed.
- Flywheel M8×1 nut: 32.5 Nm (24 lbf.ft); clutch M12×1 L carrier: 50 Nm (37 lbf.ft), with left-hand thread explicitly marked L.
- Cylinder decompression valve M10×1: 14 Nm (10.3 lbf.ft), not the leakage-test plug; spark plug M14×1.25: 25 Nm (18.5 lbf.ft).
Source: TI 46/1995, p. 11 — 5.3: engine, exhaust and rotating assembly rows.
No additional parts-table entry added.
Service note · 046
046: small-fastener torques, adhesives and ignition washer
The ignition-module screws require both Loctite 242 and a washer; nearby screws have different requirements.
- These are historical TI 46/1995 page 11 fastener-specific values, not universal torque by thread diameter. No fastener part number is supplied. Printed lbf.ft equivalents are retained alongside Nm.
- Generator IS-M4×12: 3.5 Nm (2.6 lbf.ft), Loctite 649. Chain-tensioner cover plate IS-M4×8: 3 Nm (2.2 lbf.ft).
- IS-M4×12 oil-pump cover at sprocket side: 3 Nm (2.2 lbf.ft); brake-band/crankcase: 3 Nm (2.2 lbf.ft), Loctite 242; oil pump: 3.5 Nm (2.6 lbf.ft).
- IS-M4×12 segment/fan housing: 2.5 Nm (1.8 lbf.ft); sprocket-side crankcase cover: 3 Nm (2.2 lbf.ft).
- M5 SK6 collar nut for carburetor/filter base/flange: 6 Nm (4.4 lbf.ft), remark 3/Loctite 270. The table calls the fastener a collar nut although its remark generically says screw; neither label is silently changed.
- Fan housing IS-M5×20: 7 Nm (5.2 lbf.ft). Ignition module/crankcase IS-M5×20: 7 Nm (5.2 lbf.ft), Loctite 242 AND a washer under the screw head. Do not transfer this washer requirement to every M5 screw.
Source: TI 46/1995, p. 11 — 5.3: M4 rows, intake collar nut, fan housing and ignition.
No additional parts-table entry added.
Historical fitment · 046
046: shared ignition module and higher-output generator
TI02/1996 also names 046 for the universal module and higher-output generator, not for the 066 crankshaft or flywheel.
Later reviewed guidance: 046: later ignition guidance replaces the universal-module rule
- The 066 bulletin explicitly says a universal ignition module and higher-output generator will also be installed in 046. Sections 2.2 and 2.3 identify the new versions as 0000 400 1303 and 1128 404 3501.
- This shared-component statement does not extend 066 flywheel numbers, crankshaft dimensions, crankcase compatibility, heater retrofit or X 33 917 066 changeover to 046.
- No 046-specific introduction serial, old module/generator number or all-variant coverage is given here. The 066 old/new flywheel prohibition is not a complete 046 conversion procedure.
Source: TI 2/1996, p. 2 — 2.1–2.3: explicit 046 inclusion for module and generator.
Part numbers (2)
- 0000 400 1303 — Universal ignition moduleExplicit shared-component statement · 046; variant and serial not supplied here
- 1128 404 3501 — Higher-output generatorExplicit shared-component statement · 046; variant and serial not supplied here
Historical fitment · 046
046: series 1128 replacement ignition assignment
1122 400 1314 and the listed flywheel pairings for series 1128; 150 mm ignition lead.
- Standard: 1122 400 1314 with flywheel 1128 400 1211.
- Heating: 1122 400 1314 with flywheel 1128 400 1212.
- Printed ignition-lead length: 150 mm (6 in). Preserve the printed metric and inch values; no rounding correction is inferred.
- TI01/1999 lists replacement combinations for the then-current machines, not every earlier configuration. Older machines are referred to Spare Parts for Previous Models in their own illustrated parts lists; no serial cutoff is supplied here.
- Use only the listed ignition-module/flywheel combinations. The source warns that incorrect combinations can cause excessive RPM or running in reverse; sharing a module number does not make all flywheels interchangeable.
- Universal replacement modules may differ from production modules in maker, shape and part number. The source describes installation/function compatibility within its assignments, not universal compatibility or a project hardware test.
- Some replacement modules require shortening the ignition lead and/or short-circuit wire and crimping a different short-circuit connector. The table gives ignition-lead lengths only; it supplies neither a short-circuit-wire length nor a connector part number. Do not infer that every row needs modification.
- Only the named models and printed series are covered. A shared IPL sheet does not extend this assignment to unnamed models or modern MS equivalents. This 1999 USA bulletin is historical guidance, not current availability.
Source: TI 1/1999, p. 1 · TI 1/1999, p. 2 — 1.1 general restrictions and 1.2.1 chainsaw assignments.
Part numbers (3)
- 1122 400 1314 — Replacement ignition moduleAssigned replacement · 046, series 1128, only with the listed flywheel branch
- 1128 400 1211 — Standard flywheelRequired pairing · 046, series 1128; standard only
- 1128 400 1212 — Heating flywheelRequired pairing · 046, series 1128; heating only
Service note · 046
046 arctic: keep generator, harness and flywheel versions matched
From 1 44 336 695, separate generator windings supply handle and carburetor heating; do not mix old and new system parts.
1 44 336 695 — Production introduction of the modified 046 arctic heating system; not a universal retrofit or individual-machine configuration determination.
- The handle heating system is uprated from serial 1 44 336 695; generator, flywheel, wiring harness and heating element are modified. Handle and carburetor heating now operate independently. The serial is the production introduction, not proof that an individual saw remains unmodified or a blanket retrofit instruction.
- Generator 1128 404 3501 with one winding is replaced by 1128 404 3502 with two windings, one for handle heating and one for carburetor heating. The printed winding resistances are yellow 0.8 Ohm and red 0.6 Ohm. The table does not assign either wire color to a particular heating circuit or specify tolerance, temperature or a complete test procedure.
- Flywheel 1128 400 1212 is replaced by 1128 400 1203. The source states that only magnet width differs: the previous version has 6 mm magnets, the new version 10.5 mm (printed 10,5 mm). Drawing 132TI000 KN assigns previous/new left/right; these are magnet widths, not air gaps or coil dimensions.
- Wiring harness 1128 440 3012 is replaced by 1128 440 3013. The additional wire connects the second generator winding to the handle heating system. This functional description does not supply a red/yellow circuit assignment.
- All three summary rows carry both remarks: the previous version remains a spare for older machines, and previous and new versions must not be mixed in the same machine. Keep generator, harness and flywheel versions matched; these are not unconditional one-part supersessions. Section 5 repeats the general no-mixing instruction and says terminal design ensures correct generator-wire connection.
- The broader no-mixing wording must be retained alongside section 4, which separately says heating element 1128 430 6000 continues as a replacement for all 046 arctic versions. The summary lists only generator, harness and flywheel, not the heating element. Do not erase either statement or infer that the element statement permits mismatching the three system parts.
- The last-TI reference 03.1999 is bibliography, not a supersession or an additional required repair procedure.
- Applies only to 046 arctic, series 1128. The shared 046 catalog sheets are navigation anchors, not evidence that non-arctic 046, 044 or MS 460 machines use this configuration. Historical source instructions and nominal values are not hardware measurements or current spare-stock claims.
Source: TI 28/1999, p. 1 · TI 28/1999, p. 2 · TI 28/1999, p. 3 — Introduction and sections 1–3,5,7: serial, generator values, magnet widths, harness and all summary rows/remarks.
Part numbers (6)
- 1128 404 3501 — Single-winding generatorPrevious; older-machine spare · 046 arctic configuration specified in TI28/1999 only
- 1128 404 3502 — Two-winding generatorNew matched system · 046 arctic configuration specified in TI28/1999 only
- 1128 400 1212 — Flywheel with 6 mm magnetsPrevious; older-machine spare · 046 arctic configuration specified in TI28/1999 only
- 1128 400 1203 — Flywheel with 10.5 mm magnetsNew matched system · 046 arctic configuration specified in TI28/1999 only
- 1128 440 3012 — Wiring harnessPrevious; older-machine spare · 046 arctic configuration specified in TI28/1999 only
- 1128 440 3013 — Wiring harness with additional wireNew matched system · 046 arctic configuration specified in TI28/1999 only
Service note · 046
046 arctic: route and insulate the heating-system wiring
Keep the harness under the ignition lead and the generator wires in the housing recesses; preserve connector orientation.
- Center the insulating tubes on the connectors. Drawing 132TI028 KN shows their placement; position the generator wires in the recesses and between the housing wall and rib.
- Place the wiring harness under the ignition lead. Push the short-circuit wire into the retainer on the ignition module. Note the installed position of the spade terminal and cable lug as illustrated in 132TI029 KN; fit insulating tubes between the ribs on the housing wall.
- Terminal design ensures correct generator-wire connection according to section 5. It does not remove the matched-version requirement or authorize a guessed wiring pinout. Figures 132TI026 KN (harness) and 132TI028/029 KN (routing) are installation evidence, not numbered replacement parts.
- This TI supplies no additional connector, insulating-tube or wire order numbers, wire colors for the two heating circuits, terminal torque, or electrical test sequence. Preserve the illustrated orientation instead of inventing those details.
- Applies only to 046 arctic, series 1128. The shared 046 catalog sheets are navigation anchors, not evidence that non-arctic 046, 044 or MS 460 machines use this configuration. Historical source instructions and nominal values are not hardware measurements or current spare-stock claims.
Source: TI 28/1999, p. 2 · TI 28/1999, p. 3 — Sections 3,5–7: complete routing bullets, connector/retainer figures and matched-version constraint.
Part numbers (1)
- 1128 440 3013 — Revised wiring harnessInstall with matched revised heating-system parts · 046 arctic configuration specified in TI28/1999 only
Wrong number or missing part for the 046? Report a correction →