← 044/046 · MS 440/460/461

Stihl 1128 · Section G · 7 of 16 · 23 parts

Wiring harness

Fits 046.

Parts diagrams →

Historical fitment & changes (5) — includes parts and conditions not shown on this drawing.

Position —

Go to table row → Where else is this used →
1101111111212131313141415151616161616171717171819220212122222222233445556666777788889
Tap a numbered callout to view that part. Use +/− or pinch to zoom. Scroll to browse.

Parts (23)

PosPart numberDescriptionQty
1 1128 440 3002 Wiring harness 1
2 1128 440 3003 Wiring harness 1
3 1128 440 3013 Wiring harness Fitment / change note → 1
4 0000 989 0814 Grommet 1
5 0751 030 8969 Terminal socket A5-1.5 no longer available from factory 1
6 0751 030 8957 Terminal socket 4.8-1/0.8 no longer available from factory 1
7 0751 030 8955 Terminal socket 4.8-1/0.4 no longer available from factory 1
8 0751 030 8407 Terminal socket 2.8-1/0.4 no longer available from factory 1
9 1118 431 6600 NLA Terminal pin no longer available from factory 1
10 1118 431 6700 NLA Terminal socket no longer available from factory 1
11 0751 030 8963 Terminal socket 12-1 no longer available from factory 1
12 0000 989 0812 Grommet 1
13 1118 431 6600 NLA Terminal pin no longer available from factory 3
14 1118 431 6700 NLA Terminal socket no longer available from factory 2
15 1121 442 0402 NLA Insulating hose 35 mm / 1.4'' Fitment / change note → 2
16 1121 442 0402 NLA Insulating hose 35 mm / 1.4'' Fitment / change note → 5
17 1125 084 8900 Grommet 1
18 1128 440 3012 Wiring harness Fitment / change note → 1
19 0751 030 8968 NLA Terminal socket 5-2.5 no longer available from factory 1
20 not sold separately Terminal socket not available as a separate item 1
21 1118 431 6600 NLA Terminal pin no longer available from factory 2
22 1121 442 0402 NLA Insulating hose 35 mm / 1.4'' Fitment / change note → 4
23 1118 431 6700 NLA Terminal socket no longer available from factory 1

Parts are not interchangeable across engine series — check yours before ordering. NLA = withdrawn by STIHL before 2012.

Historical fitment & changes

Source-reviewed service notes supplement this IPL. These are not extra drawing positions or a complete revision history. Availability statements belong to the bulletin’s date.

Conditional replacement · 046

046 arctic: thermostat moved to the heater

The arctic configuration changed to the standard HD-8 A carburetor together with a new heating element carrying the thermostat and an additional gasket.

Later reviewed guidance: 046 arctic: 8 Ohm heater and retained replacement element

X 37 180 486 — Introduction of the combined carburetor/heater arrangement for the specified arctic variant.

  • Applies to 046 arctic, not a blanket carburetor substitution for all 046s.
  • New heating element 1128 430 6000 and gasket 1128 129 1100 accompany the new carburetor arrangement. The gasket is fitted between carburetor and heating element.
  • The older 1128 434 5101 heater and 1128 430 0501 thermostat remained available for older machines in this TI; the new thermostat is not listed as a separate service item.
  • X 37 180 486 is the introduction of this combined arctic configuration, not a model-identification range or permission for an unmatched retrofit.
  • The thermostatic switch moves from the carburetor end cover to the heating element; the respective standard carburetor is then used with the new element. Gasket 1128 129 1100 fits between carburetor and element to improve heat distribution according to the source, not a reproduced temperature measurement.
  • The original carburetor 1128 120 0613 includes the thermostatic switch; new heating element 1128 430 6000 includes the new switch. The new-switch table entry is not an orderable number: it is unavailable separately. Original carburetor 1128 120 0613 is no longer factory-supplied; standard carburetor 1128 120 0610 is already in inventory. Retention of older heater/switch spares is not permission for an unmatched retrofit or a current-stock claim.

Source: TI 9/1997, p. 3 · TI 9/1997, p. 4 — Complete section3:model-specific arctic carburetor/heater rows,gasket drawing,serial and all supply remarks.

Part numbers (6)
  • 1128 120 0613 — HD-9 A carburetorOriginal arctic configuration · 046 arctic with thermostat on carburetor
  • 1128 120 0610 — HD-8 A carburetorNew arctic configuration · 046 arctic only with matched new heating arrangement
  • 1128 434 5101 — Heating elementOriginal equipment · 046 older arctic heating arrangement
  • 1128 430 0501 — Thermostatic switchOriginal service part · 046 older arctic arrangement; not the new integrated thermostat
  • 1128 430 6000 — Heating element with thermostatRequired companion · 046 revised arctic heating arrangement
  • 1128 129 1100 — GasketRequired companion · Between carburetor and new heating element

Historical fitment · 044 / 046

Generator connector: insulating tube replaces housings

TI 09/1997 replaces the generator connector pin and socket housings with insulating tube 1121 442 0402.

  • Applies at the wiring-harness/generator plug connection on the heating-equipped configurations; not to every connector on either saw.
  • The tube is the replacement insulation, not a replacement electrical contact. The TI gives no numeric introduction cutoff.
  • The summary specifies tube dimensions 3.3 × 0.9 × 35 for 1121 442 0402 without an explicit unit or axis convention on this page; do not invent either from the three values alone. Both original pin housing 1128 431 8400 and socket housing 1128 431 8700 remain factory-supplied only while stocks last.
  • This connection change is in progress; the preceding arctic-heater serialX 37 180 486 is not its cutoff. The footer identifies last TIs 044:38/1996 and 046:05/1997. The 09/1997 issue bears a 1996 copyright imprint; the imprint is not silently changed or treated as the modification date.

Source: TI 9/1997, p. 4 — Complete section4:connection prose,all three table rows,dimensions,introduction/supply remarks and footer.

Part numbers (3)
  • 1128 431 8400 — Pin housingOriginal insulation · 044 / 046 generator plug connection
  • 1128 431 8700 — Socket housingOriginal insulation · 044 / 046 generator plug connection
  • 1121 442 0402 — Insulating tubeReplacement insulation · 044 / 046 wiring-harness/generator connection

Service note · 046

046 arctic: keep generator, harness and flywheel versions matched

From 1 44 336 695, separate generator windings supply handle and carburetor heating; do not mix old and new system parts.

1 44 336 695 — Production introduction of the modified 046 arctic heating system; not a universal retrofit or individual-machine configuration determination.

  • The handle heating system is uprated from serial 1 44 336 695; generator, flywheel, wiring harness and heating element are modified. Handle and carburetor heating now operate independently. The serial is the production introduction, not proof that an individual saw remains unmodified or a blanket retrofit instruction.
  • Generator 1128 404 3501 with one winding is replaced by 1128 404 3502 with two windings, one for handle heating and one for carburetor heating. The printed winding resistances are yellow 0.8 Ohm and red 0.6 Ohm. The table does not assign either wire color to a particular heating circuit or specify tolerance, temperature or a complete test procedure.
  • Flywheel 1128 400 1212 is replaced by 1128 400 1203. The source states that only magnet width differs: the previous version has 6 mm magnets, the new version 10.5 mm (printed 10,5 mm). Drawing 132TI000 KN assigns previous/new left/right; these are magnet widths, not air gaps or coil dimensions.
  • Wiring harness 1128 440 3012 is replaced by 1128 440 3013. The additional wire connects the second generator winding to the handle heating system. This functional description does not supply a red/yellow circuit assignment.
  • All three summary rows carry both remarks: the previous version remains a spare for older machines, and previous and new versions must not be mixed in the same machine. Keep generator, harness and flywheel versions matched; these are not unconditional one-part supersessions. Section 5 repeats the general no-mixing instruction and says terminal design ensures correct generator-wire connection.
  • The broader no-mixing wording must be retained alongside section 4, which separately says heating element 1128 430 6000 continues as a replacement for all 046 arctic versions. The summary lists only generator, harness and flywheel, not the heating element. Do not erase either statement or infer that the element statement permits mismatching the three system parts.
  • The last-TI reference 03.1999 is bibliography, not a supersession or an additional required repair procedure.
  • Applies only to 046 arctic, series 1128. The shared 046 catalog sheets are navigation anchors, not evidence that non-arctic 046, 044 or MS 460 machines use this configuration. Historical source instructions and nominal values are not hardware measurements or current spare-stock claims.

Source: TI 28/1999, p. 1 · TI 28/1999, p. 2 · TI 28/1999, p. 3 — Introduction and sections 1–3,5,7: serial, generator values, magnet widths, harness and all summary rows/remarks.

Part numbers (6)
  • 1128 404 3501 — Single-winding generatorPrevious; older-machine spare · 046 arctic configuration specified in TI28/1999 only
  • 1128 404 3502 — Two-winding generatorNew matched system · 046 arctic configuration specified in TI28/1999 only
  • 1128 400 1212 — Flywheel with 6 mm magnetsPrevious; older-machine spare · 046 arctic configuration specified in TI28/1999 only
  • 1128 400 1203 — Flywheel with 10.5 mm magnetsNew matched system · 046 arctic configuration specified in TI28/1999 only
  • 1128 440 3012 — Wiring harnessPrevious; older-machine spare · 046 arctic configuration specified in TI28/1999 only
  • 1128 440 3013 — Wiring harness with additional wireNew matched system · 046 arctic configuration specified in TI28/1999 only

Service note · 046

046 arctic: 8 Ohm heater and retained replacement element

The revised element changes shape and thermostat orientation; 1128 430 6000 remains a stated replacement for all 046 arctic versions.

  • Section 4 says the previous heating element 1128 430 6000 is replaced in production by a new version. Its shape is optimized for use in several models, its thermostat is turned and its wiring routed accordingly; drawing 132TI030 KN preserves the installation orientation. No rotation angle or list of those other models is specified.
  • Both heating-element versions have the same stated resistance, 8 Ohm. This is not either generator-winding resistance (0.8 or 0.6 Ohm), nor a temperature/tolerance-qualified pass/fail test.
  • The same section explicitly says heating element 1128 430 6000 will continue to be supplied as a replacement for all versions of the 046 arctic. Preserve that historical service statement alongside section 5’s general ban on mixing old and new parts; do not broaden it to mixed generator/harness/flywheel sets or other models.
  • The bulletin does not give a distinct order number for the new production heating element. No number is inferred from later catalog entries or from the shared part prefix. The existing exact-046 carburetor/wiring anchors are navigation only; no new drawing position, universal carburetor fitment or unidentified heater order number is created.
  • Applies only to 046 arctic, series 1128. The shared 046 catalog sheets are navigation anchors, not evidence that non-arctic 046, 044 or MS 460 machines use this configuration. Historical source instructions and nominal values are not hardware measurements or current spare-stock claims.

Source: TI 28/1999, p. 1 · TI 28/1999, p. 2 · TI 28/1999, p. 3 — Section 4 heater shape, thermostat and 8 Ohm value; section 5 and summary no-mixing scope.

Part numbers (1)
  • 1128 430 6000 — Heating elementPrevious production element; retained replacement for all 046 arctic versions · 046 arctic configuration specified in TI28/1999 only

Service note · 046

046 arctic: route and insulate the heating-system wiring

Keep the harness under the ignition lead and the generator wires in the housing recesses; preserve connector orientation.

  • Center the insulating tubes on the connectors. Drawing 132TI028 KN shows their placement; position the generator wires in the recesses and between the housing wall and rib.
  • Place the wiring harness under the ignition lead. Push the short-circuit wire into the retainer on the ignition module. Note the installed position of the spade terminal and cable lug as illustrated in 132TI029 KN; fit insulating tubes between the ribs on the housing wall.
  • Terminal design ensures correct generator-wire connection according to section 5. It does not remove the matched-version requirement or authorize a guessed wiring pinout. Figures 132TI026 KN (harness) and 132TI028/029 KN (routing) are installation evidence, not numbered replacement parts.
  • This TI supplies no additional connector, insulating-tube or wire order numbers, wire colors for the two heating circuits, terminal torque, or electrical test sequence. Preserve the illustrated orientation instead of inventing those details.
  • Applies only to 046 arctic, series 1128. The shared 046 catalog sheets are navigation anchors, not evidence that non-arctic 046, 044 or MS 460 machines use this configuration. Historical source instructions and nominal values are not hardware measurements or current spare-stock claims.

Source: TI 28/1999, p. 2 · TI 28/1999, p. 3 — Sections 3,5–7: complete routing bullets, connector/retainer figures and matched-version constraint.

Part numbers (1)
  • 1128 440 3013 — Revised wiring harnessInstall with matched revised heating-system parts · 046 arctic configuration specified in TI28/1999 only

Wrong number or missing part for the 046? Report a correction →